Search Documents

By Cory J. E. Yacyshyn

Anchored steel pipe piles are being used more frequently in British Columbia for shoreline projects such as public ferries, cruise ship docks, containership terminals and locally in the expansion of the Vancouver waterfront convention center. While a 36? diameter driven pile may provide adequate compression loads it will not always achieve enough penetration to provide the required tension loading. That is why bundles of threaded anchors or strands are drilled through the center, past the pile tip, and anchored into the underlying strata. Drilling up to 250 feet deep through the piles in variable water bearing strata presents challenges. Southwest Contacting Ltd. (SWC) recently completed the three largest anchored pile projects in BC; Vancouver Port and Convention Center Expansion, Vanterm Container Terminal and the new Prince Rupert Cruise Ship Terminal. This paper will present the separate challenges encountered drilling the anchors. At Prince Rupert, the recently completed Northland Cruise Ship Dock ultimately required a cased system to drill and install triple thread bar anchors. When 200 foot long steel pipe piling was unable to penetrate the highly fractured gneiss/schist bedrock to obtain a seal and consolidation grouting was unsuccessful, a modified cased system was advanced deep enough into the rock to eventually seal. The 3-#20 bars were changed to 12-strands since the bars wouldn?t fit through the smaller cased hole. The options were limited because each dolphin only had enough room for a small hydraulic drill rig that wouldn?t have the power to fully case the holes. The Canada Place Pier Extension in Vancouver?s Harbor led to the development of an innovative tip design used later at Vanterm. The 36? diameter steel pipe piles were driven closed end but modified to permit drilling through a concrete plug at the base. The driving of the piles at Canada Place often knocked out the plug so we were faced with 50 feet of sand up inside the pile when the drilling started. This led to discussions on how to safely remove the sand, solidify the tip, and continue drilling to get past the tip without undermining the pile. Finally, Vanterm Berth Extension was completed with a unique drilling system because the pile tips stopped in hydraulic sands, as opposed to the native till. We were faced with advancing the casing to the till without undermining the base of the pile. With 100 psi water pressure at the pile base after we broke through the concrete plug, the trick was to prevent charging the sand with our 250 psi air which liquefies it and forced it up our drill casing. And of course, it has to happen just before Christmas holidays!

Jan 1, 2004

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

By George Brien, O&apos

The history of the lighting of mine workings dates back to the early part of the 18th century, when small candles known as tallow dips, were used. These were set or held in a lump of wet clay. When looking for gas the flame of. the candle was reduced to a mere glimmer by surrounding the wick below the flame with clay. The candle was then very cautiously raised from the floor toward the roof, the observer screening the brighter portion of the flame with his hand and watching for the first appearance of the pale blue cap above the flame, even at that time, known to indicate the presence of gas. When this appeared the candle was lowered quietly and its flame extinguished before attempting to drive out the gas. A very common and dangerous practice adopted at that time was to get rid of the gas by firing it. This was done by a person selected for his nerve rather than for his caution. Dressed in a? suit of dampened sackcloth or leather, this man well termed a "fireman", would lie prone on the floor of the roadway and light the gas above him by raising his candle fastened to the end of a long stick. If he survived, which was not always the case, he would withdraw promptly to fresh air after the flame had passed over him.

Jan 1, 1924

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

By M. Klapwijk

Ancient Metallurgy - In addition to the preceding three papers, the following three contributions were received for publication 1. An analysis of Bantu-made iron implements from the Letaba district M. KLAPWIJK INTRODUCTION It has often been stated that it is hardly possible in South Africa to classify Bantumade iron hoes according to their places of origin and manufacture. It is well known that these hoes were used for barter, and as currency in the purchase of livestock or the payment of lobolo, although reports of the value of the hoes differ widely. The difficulty in their classification has arisen from their distribution over a very wide area.

Jan 1, 1974

By G. M. Thain

Ancient Mining - The following three contributions were received for publication in addition to the preceding papers. 1. Ancient gold-mining sites in the Transvaal G. M. THAIN* Pre-European gold mining and working in South Africa is a tantalizing field for conjecture. Well over thousand sites have been identified in Rhodesia, but here we have had to reach double figures, judging by published accounts. Geologically, the Transvaal is less amenable primitive exploitation, but it difficult to reject the idea that the knowledge gained to the north did not have its influence south of the Limpopo.

Jan 1, 1974

By T. N. Huffman

Ancient mining and Zimbabwe T. N. HUFFMAN*. Ph.D. (Illinois) (Visitor) Ancient gold mining and Zimbabwe have been commonly associated for over a hundred years, either in terms of an exotic colony for gold export or as an African state based on the East Coast trade. The stratigraphy and radiocarbon dates from Zimbabwe and the known sequence for the Rhodesian Iron Age demonstrate that Zimbabwe was built after AD. 1000. A review of the evidence for ancient gold mining shows a similar antiquity, and a complementary rise in prosperity in Arab settlements on the East Coast indicates that gold was not extensively mined until the eleventh century. Large quantities of imported articles at Zimbabwe indicate the extent of trading during the fourteenth and fifteenth centuries, and the origins of Zimbabwe probably lay in an overflow of wealth from the gold trade during the twelfth and thirteenth centuries. Zimbabwe was abandoned by the sixteenth century because of environmental factors.

Jan 1, 1974

By F. E. Gregory

MINING methods and customs in many districts of England are to this day strangely bound about by the records and traditions of the past. In some mining fields this is more apparent than in others, yet it is everywhere in evidence, for Cornwall with her mines under the sea, Wales with her famous quartzites, and Derbyshire with her remarkable cavern deposits, are all tinctured with quaint customs that have come out of the almost forgotten past. Here, modernism has never replaced tradition, and many of the laws are woven of the woof and warp of ancient custom. Indeed, these things exist because they have come to be part and parcel of the civil laws. And these laws are observed with meticulous care and accorded all the reverence due their venerable age. All activities pertaining to the mining of metals are hedged around by curious and ofttimes clumsy laws, each minute and trivial detail being covered by the civil code, and each petty law enforced by an ofttimes pompous official.

Jan 1, 1933

By T. M. Evers, R. P. Van Den Berg

Ancient mining in Southern Africa, with reference to a copper mine in the Harmony Block, north-eastern Transvaal T. M. EVERS. B.A. (Birm.) (Visitor) and R. P. VAN DEN BERG. B.Sc. (Wits.) (Visitor) A recently discovered mine on the farms Harmony 24 and 25 in the Letaba district has been investigated archaeologically by T. M. Evers and geologically by R. P. van den Berg. The archaeological investigations shed light on the mining techniques and accompanying metallurgical techniques, while the geological investigations give information on the structure and mineralization of the mine. Comparisons with other investigated ancient workings show that mining was well understood in Iron Age times, before the African peoples had any contact with Europeans.

Jan 1, 1974

By I. R. Phimister

'Ancient' mining near Great Zimbabwe I. R. PHIMISTER. B.A. Hons. (Nottingham). B.A. Spec. Hons. (Rhodesia) (Visitor) In proposing reasons for the geographical location of Great Zimbabwe, the paper re-examines the popular assumption that Zimbabwe is comparatively remote from the known areas of 'ancient' goldmining. The lack of 'ancient' workings in the neighbourhood of Zimbabwe is pointed out, and it is suggested that the mining of placer deposits of gold may have played some part in the development of Zimbabwe on its particular site.

Jan 1, 1974

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Fengyan D

Removing the interference of latter events, the data of geophysical (such as gravity and aeromagnetic) anomalies may indicate whether the mobile belt exist and whether the adjacent terrains of the mobile belt originally belong to one single unit. The petrotectonic assemblage can provide informations about the tectonic setting where it was generated from. The structural style can exhibit the kinetic and kinematic processes. The form of ancient isogeotherm may reflect the ancient geothermal regime which is related to the tectonic mechanism. In general, the early Precambrian terrains suffered polymetamorphism and multiple structural deformation. The researches must be carried out for the distribution of paleogeotharm and m.tamo'phic facies and zones on the basis of recovering the early structural style with structural analysis method; then a relatively correct conclusion may be geined on the ancient geothermal regime. This method can be known as "Ancient Thermotectonic Analysis". Through the sythetical research, a real knowlege about the tectonic setting of early Precambrian mobile belt can be obtained.

Jan 1, 1990

By M I. Pownceby, S Hapugoda, H Han, V Nunna, L Lu

Charcoal produced from Syzygium Zeylanicum (local name: Yakada Maran = iron killer) trees were widely used in ancient Sri Lankan iron smelting practices. In this study, relict charcoal from Syzygium Zeylanicum tree trunks, branches and leaves were analysed for the first time. Unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOX) crystals were identified preserved in plant cell structures by optical mineralogy and SEM analysis. Thermogravimetric Analysis (TGA) of CaOX showed that it displayed three decomposition stages, releasing H2O at 177°C, CO at 493°C and CO2 at 750°C. Following the identification of CaOX in Sri Lankan charcoal, a series of reduction tests on a low-grade, high-P iron ore fine sample (high SiO2: 5 wt. per cent; Al2O3 4 wt. per cent; P: 0.135 wt. per cent) doped with CaOX were carried out at various temperatures. Samples were analysed by XRF, SEM and EPMA to determine the degree of reduction and the effect of reduction on the deportment of impurities, in particular P. Reduction tests at 800°C and 900°C with 5 wt. per cent CaOX showed that the reducibility increased to over 65 per cent. At temperatures above 900°C, P was located mainly within a fine, interstitial glass matrix suggesting that the CaOX flux enhanced removal of P from iron-rich pre-cursor phases to form glass. Preliminary magnetic separation tests to remove the P-rich interstitial glass were unsuccessful due to the fine grain size. Further complete reduction tests at temperatures above 1200°C with addition of coke to convert the iron oxides into Fem were conducted with samples doped with 10 wt. per cent CaOX, 10 wt. per cent CaCO3 and equivalent undoped samples. Results confirmed the preferential P-incorporation into a glassy matrix in the CaOX samples although some rare P incorporation into the metallic phase was noted. Experimental results, including comparisons with the CaCO3 fluxed and undoped samples, are discussed in view of the potential for CaOX flux for removing P (and potentially other impurities) from P-rich iron ores.

Nov 8, 2021

By Denghong Wang

Abstract- The Ashele Cu-Zn deposit is a recently discovered volcanogenic massive sulfide deposit in Xinjiang, China, hosted by Lower to Middle Devonian submarine bimodal volcanic rocks. The primary ores of this polygenetic deposit are represented by massive syn-depositional pyrite, chalcopyrite, and sphalerite, and were formed by submarine exhalation. Hydrothermal alteration consists of strong sericitization, chloritization, silicification, and carbonatization of the metavolcanic rocks beneath the massive orebodies. Depletion of Na2O is an obvious chemical change in the hydrothermal halo. Geological and geochemical evidence suggest that the Ashele Cu-Zn massive sulfide deposit was formed by submarine exhalation related to bimodal volcanic rocks, trapped in a rifting basin, then deformed by shearing, and thermally metamorphosed by the intrusion of dacitic porphyry. Sulfur and lead isotopic studies indicate that metals such as copper and zinc may have originated from spilites, but that volatile components, especially sulfur, were derived directly from submarine volcanic magmas.

Jan 1, 1999

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999

By Jian Deng, Haitian Sun, Zengqian Hou, Shuhe Song

"Abstract - Volcanogenic massive sulfide (VMS) deposits, an important base-metal deposit type in China, occur widely in submarine volcanic districts of variable magmatic affinities. These VMS deposits range in age from Archean to Mesozoic, but most are in Proterozoic and Paleozoic sequences. More than 60% of VMS deposits formed in the Paleozoic, the most important metallogenic eon. Three important Paleozoic VMS-metallogenic provinces include Northern Qilian, Sanjiang and Altai provinces. The Proterozoic constitutes the next important era, but with no VMS deposits in the middle Proterozoic. VMS deposits associated with the Proterozoic volcanic rocks occur around the Yangtze Platform and in the western Kunlun-Qinling. The Triassic is third in importance, with VMS deposits concentrated in the Sanjiang Tethys. The Archean has only one VMS deposit, on the northern margin of the Sino-Korea Platform.Five distinct compositional classes of Chinese VMS deposits have been distinguished: Cu, Cu- Zn (or Zn-Cu), Cu-Fe, Zn-Pb-Cu, and Pb-Zn (-Cu). The Cu, Cu-Co, and Cu-Zn types of deposits occur sporadically from the Archean to Paleozoic, and are closely associated with mafic and ultramafic volcanic sequences. The Zn-Pb-Cu and some Cu-Zn type deposits are restricted to the Paleozoic and Triassic, and are hosted by calc-alkaline felsic rocks in bimodal basalt-rhyolite sequences, whereas Cu-Fe and Pb-Zn type (except for the Laochang deposit) deposits are restricted to the Proterozoic and occur in calc-alkaline volcanic sequences. As large quantities of marine mafic volcanic rocks were deposited in western China, Cu and Cu-Zn deposits are major types of Chinese VMS deposits.Chinese VMS deposits formed in a wide range of paleo-tectonic settings and depositional environments, such as island-arcs, rifts, aulacogens, and ocean ridge hot spots. Among these, the rift and back-arc environments are the most important, containing about 60% of Chinese VMS deposits. Aulacogens are a subordinate environment where most of the Proterozoic VMS deposits formed. The oceanic ridge and hot-spot systems are common in the tectono-magmatic domains in China, but contain only a few small Cu and Cu-Zn type VMS deposits.The Chinese VMS deposits have usually been influenced by both deformation and metamorphism to various degrees, resulting in changes in the shape and metal distribution. Seven representative deposit styles have been recognized: sheets, sheet plus strata-bound stringer, cyclically zoned deposits, mounds, mound-like deposits, strata-bound stringer-disseminated, and stockwork-disseminated deposits. The formation of these various styles of deposits is controlled by several key factors, such as lithology and permeability of the host rocks, focused or unfocused discharge, temperature and chemical composition (e.g., salinity) of hydrothermal fluids, as well as depth of seawater."

Jan 1, 1999

By H. M. Thurgood, F. A. Godfrey, F. W. Gilbert

This is a detailed presentation of the ancillary facilities, including power production, water supply, shiploading facilities, fire-fighting equipment, housing and community services. Additional subjects discussed include construction problems, townsite philosophy and staff organization.

Jan 1, 1968

By R. P. Plasket, D. A. Ireland

Ancillary smelter operations and sulphuric acid manufacture at Impala Platinum Limited by R. P. PLASKET. Pr. Eng.. M.Sc. (Chem. Tech.). Natal (Fellow) and D. A. IRELAND. Pr. Eng.. B.Sc. (Chem. Tech.). Natal (Member) The de-watering, spray drying, and converter operations at Impala are described, aspects that may be new to the minerals industry in South Africa being elaborated. Air-pollution control necessitated the installation of a sulphuric acid plant to limit the emission of sulphur dioxide to the atmosphere. Closer control of the smelting and converting operations was required for successful operation of the acid plant on the inherently Iow and varied concentration of feed gas from converter blowing. Approximately 82 per cent of the sulphur entering the smelter is converted to sulphur dioxide, of which 67 per cent is fed into the sulphuric acid plant.

Jan 8, 1976

By Friedrich Brandstetter

Dentro del desarrollo técnico es importante desplazar las construcciones de infraestructura de forma frecuente hacia el subsuelo. Esto requiere el empleo de equipos especiales, métodos, así como de nuevos materiales de construcción con características especiales que faciliten la ejecución de estos proyectos. Así el acero fue reemplazado por resina sintética, generando resultados muy alentadores en la construcción segura en la naturaleza. En ese sentido, el presente texto señala el empleo de estas resinas y su optimización en la economía.

Mar 1, 1979