Search Documents

By Barry K. McMahon

The fundamental problem in rock mechanics is accounting for the discontinuous and anisotropic nature of the jointed rock mass. It is this problem that makes rock mechanics distinct from the mechanics of steel, glass, or concrete. Existing mathematical models explain much of the behavior of rock cores in the laboratory but, in civil engineering at least, the rocks that matter are the ones that are already broken. On the other hand, the basically descriptive methods now used in engineering geology do not lend themselves easily to mathematical analysis. A set of indices of geological properties related to the strength and deformation characteristics of jointed rock is needed. Like the index properties used in soil mechanics these will probably not have precise mathematical meaning, but once correlations are established with large scale tests they can form a basis for the transfer of test results, obtained in one area under one set of conditions, to the prediction of rock behavior in another area under another set of conditions. Indices of rock properties are even more important in rock mechanics than in soil mechanics as the cost of testing is much higher. To be useful, these indices must be easily and quickly measured and give reproducible results when measurements are made by different people. In this paper the word "joint" means all naturally occurring rock fractures with less than 3 in. of clay or other soft coating material. EXISTING INDICES OF ROCK PROPERTIES A comprehensive review of indices of rock properties for intact rock is given by Deere and Miller.' They provide charts ". . . for estimating the strength or modulus properties for intact rock from the numerical indices obtained by either the Schmidt hammer, the Shore Scleroscope,

Jan 1, 1968

By H. F. Ghezzi

The indirect method of drying coal fines is applied to filter cakes which ordinarily contain 22 to 30% moisture and are not readily transportable. The "Thermal Dryer", which operates on the mass transfer principle, has found wide use in coal preparation plants. The thermal dryer is penalized in operation by the necessity of adding coarse coal to the wet fines before entering the dryer body in order to produce a permeable bed, and thus enable hot gases to uniformly contact the wet mass. The ratio of coarse coal to fines varies from 2:1 to as much as 4:1, depending on the average particle size, moisture, and ash content of the fines.

Jan 1, 1985

By Christian M. Sagedahl

The stringent environmental regulations for air pollution regarding emission control, along with the need of dry concentrates to feed autogenous smelting processes, are enhancing the development of cleaner technologies. Indirect drying of concentrates by a Kvaemer steam dryer is a technology with promising results, reducing dust entrainment to the exhaust gas stream and leading to smaller dust separation units. The Kvaemer dryers are designed for a very high availability, a high-energy efficiency, low amount and velocity of exhaust gases, no SO2, CO or CO, emissions combined with a wide range of satisfactory operating conditions and low total operational costs.

Jan 1, 1999

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

The equilibrium experiments between the FeO-SiO2-MnO-TiO2-V2O3-Cr2O3-MgO slag system and solid pure iron were performed to investigate the vanadium and chromium distribution ratio under Ar atmosphere. The influence of w(FeO), w(V2O3) and w(Cr2O3) in slag on vanadium and chromium distribution ratios were studied at 1653 K. The experimental results were compared with calculated distribution ratios based on molecule and ions coexistence theory. Both of them showed that higher FeO content in slag would improve the distribution ratios of V and Cr between slag and hot metal. The distribution ratio of Cr or V increased with the increase of Cr2O3 or V2O3 content, respectively. To optimize the oxidation of V and Cr from hot metal, a high oxidizing slag and suitable content of Cr2O3 and V2O3 in the slag were recommended. The results provided reference for the further study on the extraction of V and Cr in VTi magnetite.

Jan 1, 2016

By J. de Bakker

It hardly needs to be repeated that if coal is to continue as America’s premier source of cheap energy, it is absolutely necessary that the carbon dioxide from its combustion somehow be sequestered. A promising method proposed to accomplish this is the “indirect” carbonation of serpentine in a concentrated magnesium chloride brine. Indirect carbonation could be also applied to precipitate magnesium in lateritic nickel processing: this would not only solve magnesium-control problems in laterite hydrometallurgy, but also reduce its energy requirements and create CO2-sequestration credits. Fifty-five percent of the electricity generated in the United States comes from coal-fired power plants, and American coal reserves can last over 500 years at 1990-level consumption1. Coal is therefore both abundant and cheap: it could (and in fact probably will) continue to be an affordable source of energy, both for producing electricity and as a feedstock for liquid hydrocarbon production by Fischer-Tropsch reactions. As a result, it is important to find a workable method of permanently sequestering CO2.

Jan 1, 2007

By A. Dell’Era, E. Ciro, C. Lupi

The indium recovery via electrowinning from sulfate baths has recently gained significant attention as it does not present toxic emissions, hermetically sealed system requirements, human health, and environmental hazards. Following previous works related to the optimization process for AISI 316L and Ni cathode, it was observed significant importance of the metal supports on the input and output parameters of the indium electrowinning process from sulfate solutions. Thus, comparing input and output parameters in both cases seems very interesting. Particularly, regarding the input parameters, the attention has been focused on the electrolyte composition, current density, and temperature, while productivity, morphology, and structure have been considered regarding the output parameters. Considering the productivity as the optimal output, the findings for Ni cathode were better than that for AISI 316L in most of the selected conditions studied. In the case of morphology, indium grains appear rounded and dendritic on the AISI 316L, while those on the Ni cathode show stratified lamellar grains. Anyway, the indium deposit obtained on Ni cathode shows bigger grains independently from the used operative conditions with respect to that on AISI 316L. Regarding the structure, it is clearly tetragonal, but preferential orientation, crystallinity, and deformation of the structure strongly depend on the metal support.

Jun 14, 2023

By Jian Wang, Hongyang Cao, Binxiu Wu, Junhong Li, Jimin Wang

"The enrichment and separation of scattered metal indium component in the pressure leaching solution with sulfuric acid from vacuum furnace germanium slag were studied by iron substitute and P204 extraction, which is supplied by shaoguan smelter. The experimental results show that the extracting power of P204 for indium from pressure leach solution is powerful. The optimal technological condition were the ratio of P204 and sulphonating serosene 3:7, phase ratio 1:3, solution pH 1.2, and extracting 5 minute. The enrichment indium solution of 21.7 g/L In at 95.2% recovery ratio was obtained by three-stage counter flow extraction and four- stage counter flow stripping.IntroductionScattered metals, such as Indium and germanium, were inriched as intermediate product or by-product during the metallurgy process of other non-ferrous metals, such as lead, zinc, copper and tin. For example, the indium and germanium were inriched in vacuum furnace germanium slag, which is the by-product of zinc vacuum distillation operation from hard zinc. It is difficult to recovery the indium from the vacuum furnace germanium slag, because the indium content is low, and the chemical composition and phase compositon were complex.Recovery indium from bearing indium zinc slag was researched extensively, such as pressure acid leaching, high temperature evaporation, solvent extraction method[l-7], acid leaching method has the advantages of high leaching rate, which can be separated hydrochloric acid, sulfuric acid and silicon fluoride acid systems. Solvent extraction method has the advantages of low production cost, fast reaction speed, high enrichment ratio, and simple operation."

Jan 1, 2013

By Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"The LCDs are used in televisions, calculators, mobile phones, computers (laptops and tablets), video games and other electronic devices. The advancements in technology make obsolete these devices, causing excessive disposal of LCDs and therefore decreasing life span of landfills. In this context, the LCDs from LED LCD TVs arise as an additional source of waste electrical and electronic equipment (WEEE). Thus, it is essential to develop LCDs recycling methods, beginning with the LCD characterization followed by displays processing, aiming the materials separation and using some Ore Treatment Techniques, and finally, the recovery of indium using acid leaching. The analysis methods that will be used in this work are: Fourier Transform Infrared (FT-IR) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES).IntroductionLiquid Crystal Display (LCD) technology is applied in modem televisions, calculators, mobile phones, computers and a wide range of electronic devices. It has replaced Cathode Ray Tube (CRT) technology as the most advantageous display product, due to lower electrical power consumption, size and weight reduction, and no radiation emission [ 1]. The constant improving of LCD screen technology reflects on its growing contribution to the amount of waste electrical and electronic equipment (WEEE): an estimated 50 million tons of WEEE are produced every year [2]. Once the most common method of its disposal are landfills, the LCD technology therefore became an environment issue [3].LCD structure is composed by components made by different materials. In order to develop a LCD recycling methodology that gives the right destination to these materials, a previous characterization stage is required. This characterization includes a disassembly process and material identification analysis. One of the LCD components is the screen, which is composed by polymeric and glass layers. The liquid crystal glass was the starting material of this study. It contains indium in the form of indium tin oxide (ITO) film. This ITO film is deposited in the glass by a sputtering process and acts as the electrode material [4,5]. It has in its composition 90% ofln203 and 10% ofSn02 [6]."

Jan 1, 2014

By P. M. Rosário

The extraction performances exhibited by a phosphoric (D2EHPA), a phosphonic (Ionquest 801), a phosphinic (Cyanex 272) and a dithiophosphinic (Cyanex 301) acid derivative towards indium recovery from a diluted sulfuric solution are evaluated and compared. Equilibrium extraction isotherms were obtained. The chemical reactions involved and the approximate stoichiometry of the In(III) extracted species by the four ligands are presented and discussed. Stripping of In(III) from loaded D2EHPA and Ionquest 801 has been accomplished successfully, but has not been so effective from loaded Cyanex 301. Plots of %E vs. pH were established for D2EHPA, Ionquest 801 and Cyanex 301, denoting their behavior towards the extraction of similar mass concentrations of In(III), Fe(III), Fe(II) and Zn(II). Cyanex 301 is the least selective towards In(III), whereas D2EHPA and Ionquest 801, both for a pH = 0.5, do not extract Zn(II) at all.

Jan 1, 2003

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high hearing loads and elevated operating temperatures, the life of hearings made from tin-hale or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in hearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on hearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condition, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organizations of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements. Investigation, undertaken with this in view, indicated that the addition of fractional percentages of the metal indium to the cadmium bearing

Jan 1, 1938

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condi-tion, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organiza-tions of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements.

Jan 1, 1938

By Nick Chlumecky

INTRODUCTION Column-type supports are used to prevent roof falls in underground excavations. The first individual column supports were made from timber that was cut to fit the irregular heights of mine seams. Because the seam height of the material removed varied throughout the mine, timber posts generally could be used only once. During the I 920s, steel friction props began to appear in British and European mines, and, by the 1950s, thousands of these props were being used. However, the steel friction props were heavy, difficult to install, and difficult to recover. Furthermore, the friction props could not be preloaded, and their yielding behavior was rather erratic. In 1946, hydraulic props were introduced in En¬gland, and, within a few years, they replaced friction props throughout Europe. The first application of hy¬draulic props in the United States occurred in the 1950s, during early experiments with longwall mining. Modern technology and high-production mining procedures have combined to make the use of hydraulic props a very acceptable method of providing temporary heavy-duty support for production areas. In areas such as development headings, where only modest roof loads are expected, lighter-duty jackscrews, ratchet jacks, and light hydraulic props are used. ADVANTAGES OF HYDRAULIC SUPPORTS The acceptance of hydraulic supports has been wide¬spread during the past 25 years, proving their reliability and effectiveness in preventing roof falls. Some of the advantages provided by hydraulic supports are: 1) Individual hydraulic props can be installed within 30 sec, resulting in a minimum exposure of per¬sonnel and equipment to an unsupported roof. 2) Hydraulic props can be preloaded to more than 4.5 t (5.0 st), increasing the frictional resistance between the rock strata. Thus, the roof is kept tight, improving the behavior of the unsupported ground. 3) If gradual roof sagging or bottom heaving im¬poses an irresistible force, the hydraulic prop yields gradually and continues to support the ground. 4) The support capacities of the hydraulic props most widely used range between 10 and 20 t (11 and 22 st). Their support capacities are maintained during yielding to an irresistible force. 5) Hydraulic props can be recovered rapidly. Where no other supports are provided for the roof, as in pillar¬ing operations, the hydraulic props can be recovered by remote means. 6) The length of hydraulic props is readily adjust¬able allowing them to be reused in seams where roof height varies. 7) Studies of mining operations indicate that the use of hydraulic props increases both personnel safety and mine productivity. DESCRIPTION Figs. I and 2 illustrate typical hydraulic props used in mines in the United States. Fig. I illustrates a prop

Jan 1, 1982

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By Lawrence M. J

It must be stressed that the following comments are offered only to assist mineral industry professionals in understanding the issues involved in personal liability. The information and views expressed herein are not intended to be a comprehensive guide or definitive statement of the law and they should not be regarded as a substitute for specific advice for individual situations. Readers should consult their own legal and other professional advisers before applying the content of this paper to their own particular circumstances. It is hardly news that work in the mining industry is governed by a complex regulatory and legal system which is constantly changing, but few realise just how directly they can be affected and become personally liable for any breaches. These may result in civil or criminal proceedings and personal assets are at risk. Owners, company directors, managers and now employees are at risk, together with consultants, contractors and suppliers of equipment or consumables, as well as government inspectors. They are liable for their personal decisions to act (or failure to act) in managing operations or carrying out directions, as well as for the actions of others under their control. This paper identifies the areas where such individuals in the open pit mining industry in Australia face the risk of personal liability and measures which can be used to minimise the risk or which can be used to make out a defence to legal action which could arise. There have always been a myriad of Commonwealth, State and Local Government laws and regulations with which to comply, and now international protocols are being used as a basis to impose greater obligations on all people. Once, the `corporate veil' gave some protection to the individual, but today there is negligible protection from the full force of the law. Not only are there various types of law enforcement officers, but public interest groups, shareholders, customers, suppliers, creditors etc may litigate. This paper is not intended to be an exhaustive discussion of the provisions of all the legislation or case law where individuals can be held) personally liable. These areas would include environmental, pollution and heritage law (including Aboriginal sacred sites); occupational health and safety (including workers' compensation) law; trade practices and fair trading law; contract law; corporations law (including the requirements of the Australian Stock Exchange [ASX] and Australian Securities Commission [ASC]); industrial relations law; anti-discrimination and sexual harassment law; taxation (including superannuation trustee) law; and the Common Law. The focus is on the following areas of regulation, which are outside the usual experience of those in the open pit mining industry (the Mining Acts and Regulations are specifically not dealt with here): ò Environment Law; ò Trade Practices Law; ò Occupational Health and Safety Law; and ò Corporations Law.

Jan 1, 1994

By John V. Beall

Probably the only hotel in the world with near 100% occupancy at all times is the modern Hotel Indonesia in Djakarta. However, there is little gaiety among the scores of business men who occupy the hotel because they fret as days grow into weeks in seemingly interminable negotiations with government officials. As one man put it, "time is a dimension that they [Indonesians] have never grasped." But the visitors still come in droves to investigate business opportunities in this sprawling nation of tropical islands which is, with 120 million people, the fifth largest nation in the world. Approximately $300 million is being spent each year in Indonesia by foreign companies and governments. Aid grants from the latter are derived about one third from the United States, one third from Japan and the remainder from many nations. Djakarta is a far cry from pleasant colonial Batavia, as the city was called under the Dutch. The orderly colony of prewar days was managed as an agricultural and trading dependency of Holland. The Dutch did little about educating the people. The islands were controlled by the Japanese during World War II and afterwards there was a war for independence--which was attained in 1949. In the ensuing years, President Sukarno devastated the economy by squandering money on a gigantic scale. A Communist-attempted coup in 1965 resulted in a military takeover and the extermination of Communists. The new government under Suharto, which took over all power in March 1966, found itself in a situation where bare survival was the first consideration.

Jan 1, 1970

By J. Sulaiman Lubis

Indonesia is a developing country in Southeast Asia with a population of some 180 million people. It has a stable political environment and currently enjoys high rates of economic growth. Indonesia has abundant reserves of natural resources, ample for its own needs and for export. Energy resources include oil, gas and coal. The oil and gas industries are well established domestically and for export. In the last few years, though, coal industry development has been rapid. Coal resources from bituminous to lignite amount to more than 30 Gt (33 billion st). That is more than enough to meet domestic needs and provide significant amounts for export. Figure 1 shows coal basins in Indonesia. Coals in Indonesia are generally young steaming coals. They are very low ash and sulfur, high volatile, bituminous B and C. The Indonesian government's state coal company is called Perum Tambang Batubara. The company has actively promoted the development of its coal for domestic and export markets. In particular, the government has placed priority on non-oil exports of which coal is a major element. The government strives to honor all contractural commitments for the export of Indonesian coal from contractor, private and government mines. From 1987 through 1989, coal production has increased from about 3 Mt (3.3 million st) to 9 Mt (9.9 million st). Exports have grown from I Mt (1.1 million st) to 3 Mt (3.3 million st). These are significant increases for a small industry with limited infrastructure. But with growing investment and development, these production and export levels will increase substantially, and Indonesia will be a significant world supplier of coal in the 1990s.

Jan 1, 1990

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world's most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7'3 of Indonesia's people reside on Java, or on 70/0 of the country's land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By A. Motamedi

Indoor localization has gained importance as it has the potential to improve various processes related to the lifecycle management of facilities and to deliver personalized and location-based services. Radio Frequency Identification (RFID) based systems, on the other hand, have been widely used in different applications in construction and maintenance. This paper investigates the usage of RFID technology for indoor localization of RFID equipped movable assets during the operation phase of facilities. The location-related data on RFID tags attached to fixed assets are extracted from a Building Information Model (BIM) and can provide context-aware information inside the building which can improve Facilities Management (FM) processes. The paper proposes a new approach to use received signals from available reference tags in the building attached to fixed assets to locate movable assets. The approach uses signal pattern matching and clustering algorithms for localization. As a result, a user equipped with an RFID reader is able to estimate the location of target assets, without having access to any Real- Time Location System (RTLS) infrastructure. A case study is performed to demonstrate the feasibility of proposed methods.

Aug 1, 2013