Search Documents

By Knijnikov M, Cameron D

Coal Quality management and the control of the flow of coal through complex mining preparation and transport phases of standard mining operations has assumed greater importance over recent years.

Jan 1, 1998

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Steven Putt

The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

Feb 1, 2020

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

By M. Balamurali, K. M. Seiler

Modelling stockpiles is a key factor of a project’s economics and operation in mining, because not all the mined ores are not able to mill for many reasons. Furthermore, the financial value of the ore in the stockpile needs to be reflected on the balance sheet. Therefore, automatically tracking the boundaries of the stockpile facilitates the mine scheduling engineers to calculate the tonnage of the ore remaining in the stockpile. This paper suggests how the dynamic of stockpile shape changes caused by dumping and reclaiming operations can be inferred using polygon models. The paper also demonstrates how the geometry of stockpiles can be inferred in the absence of reclaimed bucket information, in which case the reclaim polygons are established using the digger’s global positioning system (GPS) positional data at the time of truck loading. This work further compares two polygon models for creating 2D shapes.

Sep 1, 2021

The Porgera mine and treatment plant are located in the Enga Province of Papua New Guinea. Gold in the Porgera deposit is found free and in association with the primary sulphide mineral pyrite. The refractory nature of the gold in the pyrite r

Jan 1, 1997

By Jeffery S. Thompson, Harry Hinds

Recent advances in the development and application of the DuPont Activator Technology are discussed. Activators are catalysts of gold dissolution in cyanide solution. Plant testing of this technology in the vat leach circuit of the Homestake mine in Lead, South Dakota, showed increased gold recoveries ofup to 5%. Homestake has licensed the technology for this application and is in the process of full commercialization. Results from testing additional ores on a laboratory scale are also presented. These results indicate this technology will also increase leaching at much lower cyanide concentrations while achieving the same gold recovery.

Jan 1, 1997

By R. C. A. Minnitt, A. Akpabio

This study presents a rigorous comparison between ordinary kriging and commonly used machine learning algorithms, those being, linear regression, support vector regression, decision trees, random forests (RF), and k-nearest neighbours for spatial interpolation of platinum grade estimates in a complex ore body within the Bushveld Igneous Complex. Using only X and Y coordinates as predictors, both ordinary kriging and machine learning models were evaluated at point and block supports under traditional and spatial block cross validation frameworks. While naive validation results suggested superior performance for k-nearest neighbour and random forest (R² = 0.92 and 0.86, respectively), these were revealed to be overly optimistic under spatial dependence. Spatial block cross validation results demonstrated substantial declines in model performance, with R² often falling below zero, particularly for decision trees and k-nearest neighbour, indicating strong overfitting and limited generalisability. Ordinary kriging exhibited more stable, albeit modest, performance under spatial validation, reflecting its strength in geostatistical interpolation when contextual geological variables are unavailable. The study underscores the critical importance of spatially aware validation in resource estimation and highlights that machine learning models constrained to spatial coordinates behave as interpolators rather than true learners of geological variability. Recommendations are provided for future work incorporating geological information to enhance predictive robustness.

Mar 30, 2026

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By X. (Mike) Yao

Rock mechanics engineers must provide ground support designs that ensure a safe underground working environment. Unexpected falls of ground are unacceptable while ground support systems must be adequate. Ground support must be economic for the area supported and the time frame the opening is in use. While numerical modeling can be used for ground support design, empirical models are still the common useful design tools. Empirical models are best developed and improved from local experiences although some models, such as Stability Graph (Potvin et al, 1992), are in extensive use by the Canadian mining industry. To determine the adequacy of ground support practices at HBMS, a database of 50 fall of ground case histories between 1985 and 2001 was compiled. For each failure, the recorded data included: location, rock type, rock mass conditions, opening and failure geometry, installed ground support and failure mechanism. An analysis of the database was done to obtain an understanding of failure frequency association with rock types, stope geometry and installed ground support, and to assess what support design changes were necessary. The paper describes changes made to ground support and mining practices during the last five years, and the formation of new ground support standards and practices which have been successful in reducing ground falls while providing improved, efficient and economical ground support.

May 1, 2002

By Levent Ozdemir, Russell Miller, Fun-Den Wang

The full utilization of tunnel boring machines for excavation in medium hard and hard rock has been limited by insufficient knowledge of rock behavior under the action of mechanical cutters. An understanding of factors affecting the rock removal process will permit: (1) the more efficient design of tunneling machines, (2) the prediction of boring performance from geologic data and cores taken from the proposed tunnel alignment, and (3) an improved excavation rate, thus a lower tunneling cost.. The Colorado School of Mines, under the sponsorship of the National Science Foundation, is studying the effects of a number of parameters in regard to tunnel boring using both full and small scale laboratory tests, analyzing field boring performance and comparing the laboratory and field data. Results indicate: (1) the field boring performance can be reproduced in the laboratory, (2) the optimum spacing of cutters or optimum spacing to penetration ratios may be found in laboratory testing, (3) it is promising to use small core samples and laboratory testing to predict field machine performance and (4) effect of joints on boring rate is significant and should be included in predicting tunnel boreability.

Jan 1, 1974

By R Engle, R P. McMahan, D A. Bowman, S Schafrik, W Thabet

Preventing injuries and fatalities related to conveyor system use in the mining industry is important and increases uptime while decreasing lost time. The research presented here is funded by the National Institute for Occupational Safety and Health (NIOSH), and intended to accomplish this prevention by the use virtual environments (VEs) to improve training and help miners better understand the hazards of working around conveyor systems. Two conveyor system VEs designed to teach miners about hazards and to safely complete tasks around conveyor systems were developed for this project. The first conveyor system VE, called the instructional tour, gives the miner a semi-automated tour of a conveyor system and teaches the miner about possible hazards (eg, missing guarding) and how to safely fix conveyor problems (eg, a stuck idler) using lock-out, tag-out procedures. The second, called the virtual shift, allows the miner to freely navigate around a conveyor system to detect and avoid hazards. The miner is presented with equipment failures that need to be safely repaired during the virtual shift. If the miner fails to identify and avoid a hazard or fix a failure in a safe manner, an animation of the consequences is shown to the miner, who must start the virtual shift over. The models for the conveyor system VEs were created using 3DS Max. Desktop versions of the VEs were then created using Deep CreatorÖ, an authoring application for creating interactive 3D environments. Later, more realistic versions of the VEs were created for CAVEÖ, a room-sized visualisation system, using DIVERSE, an application programming interface. In initial evaluations of the conveyor system VEs, mining colleagues have indicated great interest in such training tools. According to their feedback, these and similar VEs would provide excellent alternatives to normal classroom training and serve as positive precursors to hands-on experience. These VEs provide new miners a chance to experience hazards associated with working around conveyor systems without being in possible danger.

Jan 1, 2008

By Stephen Hardcastle

Personnel Heat Exposure Issues In Canada?s Deep Mechanized Mines ?Project developed in 2004 ?Base/precious metal industry identified heat stress/management as a major challenge affecting productivity and operating costs ?Project started in 2005 ?Current research nearing completion ?Guidelines, further data analysis and ?Communicating the Science? will continue into 2011 Managing Heat Exposure Control?. The cost implications ?Controlling the environment ?Ventilation already a major expenses/energy user ?Large Canadian mines are currently delivering massive volumes of air 15-20 tons of air/ton ore ?Large investments in ventilation upgrades, mechanical cooling

May 1, 2010

By A. E. Stewart

Slope design in an open pit mine includes determining bench height, bench face angle and berm width. Case histories are presented of two highwall slopes (160 and 220 m or 525 and 720 ft high) excavated in dipping strata in an op¬erating coal mine. These examples illustrate the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in approximately the same lithologic and structural environment. The main differences between the slopes were the angle at which the bench faces were excavated and the excavating methods that were used. Relevent aspects are also described of the engineering geology, slope design and excavation procedures.

Jan 1, 1998

By Deni Lessard, Roger Demers, Noël R. Billette

"The Quebec Mining Association has for many years been supportive of the activities of the Centre de recherches minérales which were initiated to ensure regular production hoist and cable inspections to maintain safety and productivity standards in underground mines in Quebec. CRM and CANMET have agreed to fund a Quebec Mineral Development Agreement contract to capture this accumulated knowledge. Using VP-EXPERT to process the information and subdirectories to store regulations, the prototype access D-BASE III records on hoist information and LOTUS 123for simulating working conditions that meet local regulations and expert rules of thumb criteria. Objectives are to improve safety in emergency operating procedures, maximize hoist productivity and safety, and promote knowledge transfer to operators."

Jan 1, 1992

By I. Perus, M. Fazarinc, G. Kugler, M. Tercelj

"Ledeburitic tool steels are highly alloyed steels used for specific highly loaded applications but are characterized by low and variable hot workability. In this contribution the importance of selecting the right choice of some essential process parameters, i.e. casting temperature, solidification rate and soaking temperature, needed for improving the intrinsic hot deformability of ledeburitic tool steels, is studied. An inappropriate selection of casting temperature and cooling rate results in precipitation of unusual eutectic carbides that decreases the hot workability, whereas with the selection of appropriate soaking temperature the temperature range of safe hot working can be broadened. For each initial as-cast microstructure individually determined soaking temperature should be selected.IntroductionThe surface cracking during hot deformation of ledeburitic tool steels reduces mechanical properties and their industrial yield. These tool steels have high hardness, wear resistance and high tempering resistance on one hand, and high flow stresses and low hot deformability on the other. Decreased hot deformability of the tool steels is attributed to the type, size, shape, distribution, fraction of eutectic carbides and/or other phases, grain growth, etc. at upper limit while precipitation of secondary carbides and decreased recrystallization rate at lower limit of the safe hot deformation temperature range, [1-6].The occurrence of cracks on most exposed areas of workpiece are related to the areas where similar conditions related to upper and/or lower limit of temperature working range prevail, i.e. areas with accelerated cooling, areas with higher value of accumulated strains where also decreased recrystallization rate with simultaneously presence of higher tensile stresses takes place, furthermore areas of workpiece which are due to combustion conditions in furnace heated to higher temperatures, etc. Thus the areas, where combination of previously mentioned conditions prevails, are more exposed to cracking. This additionally requires that hot deformability of ledeburitic tool steel should be considered as a complex problem. Publications in the literature with regards to hot deformability of tool steels are predominately of a partial nature thus all reasons for unexpected occurrence of cracks are not sufficiently explained in available literature so far. Furthermore modern practice proves that previous processing parameters significantly influence the hot deformability and thus this cannot be considered as a constant value. During heating, soaking and hot deformation various processes take place: decay (decomposition) of carbides, formation of new carbides, dissolution of carbides and of alloying elements, etc. Thus depending on variation of process parameters and chemical composition, that consequently influences the processes related to carbides, shifting of decreased deformability at both limits of temperature working range to higher and/or to lower temperatures can occur, [1-14]."

Jan 1, 2012

By B. Zhu, W. E. Lee, N. Li

Al powder is used extensively as an antioxidant in carbon-containing bricks, but it cannot be used directly in water-based carbon-containing castables due to its hydration tendency. To overcome this problem, in this work, SiO2-PVA (polyvinyl alcohol) inorganic-organic hybrid coatings have been prepared via sol-gel processing, and used to coat Al powder. The hydration behaviour of uncoated and coated Al powders has been investigated in water at 60 or 100°C for 36h by examining phase and microstructural changes. While significant hydration is detected in uncoated Al powder, no obvious hydration is detected in coated Al powder, indicating that its hydration resistance has been greatly improved. Oxidation resistance of graphite coexisting with uncoated or coated Al powder was also investigated in air at 1250°C for 1.5h. The oxidation ratio of graphite coexisting with coated Al powder was similar to that of graphite coexisting with uncoated Al powder, indicating that both powders showed similar antioxidising behaviour. This, along with the much improved hydration resistance, makes the coated Al powder a potential antioxidant in carbon-containing castables systems.

Jan 1, 2004

Now you know why there is concern about mine illumination. You have some idea about how the human eye works and about the problems of glare, peripheral vision, and accommodation. And you know that lighting in a mine presents special problems because of the dark surroundings and low reflectance. This chapter describes what can be done to improve conditions. This chapter begins with a short discussion about Federal Standards on mine lighting -- what they are and what is being done to carry them out. The chapter then describes different types of lamps that can be used for mine lighting, and discusses their advantages and disadvantages. Finally, the chapter lists some things that you can do personally to improve lighting, or can point out to others so that improvements can be made. The Federal Government is doing its part to improve mine lighting by establishing regulations. Lamp manufacturers are constantly studying new lamps to provide better equipment. And your company will do its part to comply with regulations. Better lights may not be here yet, but they will be soon. But in the end, you are the one who will be using the lights, and you are in the best position to see the improvements. You are also in the best position to see and tell others where further improve¬ments can be made.

Jan 1, 1976

A novel, low-pressure adaptation of Praxair?s coherent jet technology utilizing CoJet lances was developed for application at Inco&apos;s Copper Cliff Smelter where oxygen is available in large tonnage quantities but only at relatively low supply pressures (< 193 kPa header pressure). The project objectives were to evaluate the effect of coherent jet technology on controlling oxygen lance accretion (?horn?) formation and to increase oxygen efficiency in the Inco Oxygen Top-Blowing Nitrogen Bottom Stirring (TBBS) MK Reactor used for converting nickel- contaminated chalcocite to semi-blister copper. This paper describes the development and subsequent implementation and testing of two CoJet lances in this application.

Jan 1, 2005