Search Documents

By Tacio Ferreira

A surface copper mine in the Western United States faced challenges in recovering rock and ore from final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall conditions. The operation had been using the same drill and blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at approximately 380,000 tons a year generated from an average of 60 final wall blasts performed annually. The mine engineering team and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. In this paper we present how we collected data, reviewed design standards, and found opportunities to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71% on the mine’s highwalls.

Jan 21, 2025

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By W. R. Reed, J. D. Potts

This study tests the ability of a new air nozzle system, located under the drill deck shroud, to improve the dust capture of the drill deck shroud. The system consists of three air nozzles supplied with regulated pressurized air and located midway down the shroud in the off-inlet corners of the shroud. Laboratory testing produced operating curves for the system that showed an optimum operating point of 207 kPa (30 psi) and generated respirable dust reductions of 48% to 52% from the drill deck shroud.

Jan 1, 2009

By Tácio Ferreira, Liz Diaz

Capstone Copper’s Pinto Valley Mine faced challenges in recovering rock and ore on final walls because of geotechnical constraints that require restrictions on methods for loading blastholes adjacent to the pit boundaries to preserve wall stability. The operation had been using the same drill-and-blast designs for years. With changing geology, such as harder rock, as mining progressed, material was being left unmined in final walls because of poor breakage. The amount of unrecovered, unprocessed ore was estimated at 345 kt/a (380,000 stpy) generated from an average of 60 final wall blasts performed annually. The engineering team from Capstone and Dyno Nobel engaged to minimize the amount of material left on the final pit walls. This article presents how data were collected and design standards reviewed, and the opportunities that were found to improve ore recovery from pit final walls without increasing drilling and blasting costs. The results collected from implementing the new design on two benches showed the potential for extra revenue of approximately $3.6 million generated annually from reducing final wall unrecoverable underbreak by nearly 71 percent on the mine’s highwalls.

Aug 1, 2025

By Phil Jones, Ben Johnson

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations:

Jan 1, 2019

By Phil Jones

"Dilution — planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a sixmonth period in fiscal year 2018 (FY18) that established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned versus actual toe data. These were rig alignment error, collar location change/ error and in-hole deviation.The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimizer system). The trials were undertaken in the same environment: the Cracow gold mine, an operating underground mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160 percent.The increased accuracy reduced stope dilution by reducing over-break of subgrade ore. The new technology was implemented at Cracow during the latter half of 2018. Despite utilizing the new technology for just six months of the year, the mine recorded a 5 percent overall reduction in dilution for the full year compared to the previous year (FY17); from 22 percent down to 17 percent (a net decrease of 22.7 percent). Mine management attribute a significant proportion of this reduction to the new technology, along with sequencing and planning improvements. This opinion is backed by detailed stope reconciliation data taken during the trial from 28 stopes — representing 20 percent of the total tonnes mined during FY18. The data identified that stopes drilled using the new technology recorded 62.6 percent less average dilution."

May 1, 2019

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By J. H. Russell

THE great number of wells being drilled in the Gulf Coast creates a great demand for and an opportunity to improve the methods of drilling wells and of producing oil from them. Some improvements have been made, but in the present strenuous drilling campaign at Spindletop, the quickest methods of drilling and completing wells are much too slow. Therefore, not a great deal of thought has been given to any new methods. However, one can not help but compare the method and equipment used in the present-day drilling campaign at Spindletop with those of 1901. The differences in equipment and methods are staggering and the present-day operators can hardly imagine how the old operators ever were able to drill a well. The "Old Timers" explain the reason as being that "Men were men in those days and not much machinery was necessary." Yet the development in 25 years of thought and study has brought about a great improvement in equipment and in methods. I believe there has been a great deal more thought given to the development and improvement of drilling equipment and methods and to the completion of wells than has been given to the actual production operations.

Jan 11, 1926

By Karl Ingmarsson

Larger mines spend millions of dollars annually on rock drilling tools, but often purchase based on historic consumption. The results vary from excess inventory to acute tools shortages. These lead to emergency sourcing, sometimes mixing products that don’t perform optimally. Boart Longyear analyzed the usage pattern of 96 thousand drill bits at thirteen different underground mining contracts, showing very high variability. The monthly standard deviation on a product level was 42%, with the highest for development and low volume bits. A new rule of thumb is suggested to carry only one month of safety stock for high volume bits, but increase to three months for low volume bits. This balance will reduce the risk of outages with less inventory. The accuracy can be improved by considering the specific conditions at each mine and reclassifying individual bits for a different safety stock level. Root cause analysis and collaborative forecasting between mines and suppliers can lead to further optimization of availability and inventory levels.

Feb 1, 2024

By Jeanne A. Zimmer, Brad Smith, Steve Viles, Andrew B. Cecala

A recent report evaluating silica exposure levels in the metal/nonmetal mining industry noted that bag packaging and loading are some of the occupations at the greatest risk. In addition to dust problems, the bag-stacking process is labor intensive, making lost-time injuries common due to back fatigue and strains. During the bag-stacking process, a significant amount of dust can be generated, mainly from product on the outside of the bags and from dust escaping the bag valve upon impact of the bag on the pallet. In an effort to address dust-exposure and back-fatigue issues, Malvern Minerals Co., Hot Springs, Ark., made two major improvements to its ground silica stacking facility. First, the company purchased a semi-automated bag palletizing system (Figure 1). With this system, the bag stacker does not lift the bags, but slides them across a metal table. Small jets of air exit through perforations in the table top (similar to an air hockey game), allowing workers to more easily slide each bag into the proper position. After each layer of bags is completed, the table slides open, and the entire layer of bags is loaded onto an underlying pallet. The table then closes, readying it for another layer of bags. After the entire pallet is loaded, the unit delivers the pallet to a shrink wrap and forklift pick-up area. In addition to this semi-automated palletizing unit, Malvern Minerals purchased an Overhead Air Supply Island System (OASIS) to lower the bag stacker's dust exposure. The OASIS takes outside air, directs it through MEASURING RESPIRABLE DUST The bag stacker's respirable dust exposure was monitored using a RAM-1 instantaneous dust monitor to evaluate the impact of the various changes on the palletizing process and dust-control equipment. The bag stacker wore a vest that held the 10-mm Dorr-Oliver cyclone, which classifies the respirable portion of dust. Flexible tygon tubing was used to connect the cyclone to the RAM-1 dust unit, allowing the bag stacker to perform the palletizing process with minimal interference. The RAM-1 measures respirable dust concentrations by light scattering with a sensing chamber. This device closely simulates gravimetric measurements when calibrated for a specific dust. This instrument is ideal for comparative evaluations, as was the case in this study. Since the RAM-1 is not an MSHA-approved instru¬ment for dust compliance sampling, the dust concen¬trations listed in this article should be used as a com¬parative value of respirable dust concentration and not to determine actual dust concentrations from a com¬pliance standpoint.

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

Because surface mining removes the original plant cover from the land and exposes the soil, special care is needed. Until the mined land is stabilized by revegetation, snowmelt and rainfall can pick up sediment and erode mined lands much faster than undisturbed areas. Sediment control is an important aspect of protecting the environment during mining and reclamation because without it, large amounts of sediment can clog streams, increase the risk of flooding, damage irrigation systems, harm aquatic habitat, and limit the use of water for other purposes. Stream quality can be affected many miles downstream from the mine. Before SMCRA was implemented many streams were degraded by uncontrolled sediment from mining. Sediment is controlled through careful planning and a design that incorporates a variety of measures that work together to reduce soil erosion at the mine. Disturbed areas are graded, and some areas terraced, to achieve stable slopes, reduce runoff water velocity, increase infiltration, and divert runoff into drainage channels so that it flows away from unvegetated, erodible areas. Grading along the slope contour and scarify in gun vegetated slopes with bulldozer track marks help prevent erosion by slowing down the flow of water. Runoff from haul roads is controlled by culverts and roadside ditches. Sedimentation ponds or other forms of sediment control are required at all mines to minimize the amount of sediment leaving the site.

Jan 1, 1992

By F. N. Kissell, R. A. Jankowski

The US Bureau of Mines, in close cooperation with the mining industry, has recently established several improved face ventilation techniques for longwall mining systems. These include coursing the primary face intake from tailgate to headgate, installing curtains at the intake end of the longwall face, and identifying improved techniques for measuring face ventilation parameters on longwall sections. Applying these techniques throughout the mining industry should reduce the health hazard associated with excessive exposure to respirable dust.

Jan 1, 1984

By Robert A. Jankowski, Charles A. Babbitt, Natesa I. Jayaraman

Today, approximately 31% of underground coal mining operations have designated occupations or areas with more stringent (below 2.0 mg/m3) respirable dust standards in place. Many U.S. coal mines have been able to maintain compliance with very low dust levels, and the Bureau of Mines, in an effort to identify those factors contributing to low dust levels, completed a survey of twelve continuous miner sections which were able to maintain their dust levels at or below 0.5 mg/m3. The quantity and quality of face ventilation appeared to be the most important factor in controlling dust exposure. The results directed Bureau research towards identifying improved face ventilation techniques for reducing quartz dust levels on continuous mining operations. This research has involved the evaluation of a half-curtain face ventilation technique which reduces the cross-sectional area of the entry, thus increasing the air velocity over the operator. The Bureau has also conducted extensive laboratory studies to compare tubing versus brattice, including an evaluation of both systems in a crosscut turn. In an effort to improve ventilation and reduce dust exposures of roof bolter operators working downwind of the continuous mining machine, the Bureau has evaluated two novel face ventilation systems. The first system consists of a fan discharge tubing technique which routes dusty air away from the return entry being bolted. In a technique similar to the fan/tubing concept, exhaust air from the upwind continuous miner face can be scrubbed using a dust collector to capture a portion of the dusty air, clean it, and supply it to the bolter operators as a split of clean intake air. A better understanding of face ventilation techniques should lead to solutions to the problem of more stringent dust standards due to quartz.

Jan 1, 1989

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

At the present time many coal preparation plants handle coal-clay wastes in one of two methods. In one method, the waste is processed in a thickener, followed by further dewatering through filtration, and subsequent blending with coarse waste refuse from the preparation plant. The resulting mixture is then disposed by stacking it in available storage locations. The coal-clay waste is often reslurried by rain or water from other sources, causing a potentially unsafe situation such as mud flows. The other method often used requires thickening and impoundment of the thickened slurry behind earthen dams which poses safety risks if structural failure of the dams occurs. To overcome these two problems, a flocculation method was developed which produces a stable agglomerated material resistant to reslurrying. How It Works The new method involves treating coal-clay waste with lime to raise the pH and flocculating the slurry with a nontoxic polymer of polyethylene oxide. The resulting floes are dewatered on a static screen and agglomerated. For extremely fine waste, further dewatering of the material is accomplished on a rotary trammel screen. The dewatered material may be ponded or mixed with coarse waste from the preparation plant to produce a stable mixture that can be stacked.

Jan 1, 1985

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through the use of more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the air bubbles, water, and ore, rapidly attaching the hydrophobic mineral to the bubble surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. A rougher concentrate containing 4.5 pct copper was obtained from a western porphyry copper ore containing 0.67 pct copper. Over 99 pct copper was recovered from the ore at a rate 7 times faster than conventional flotation.

Jan 1, 1991

By J. H. Schubert

Mintek has developed a level-control system, FloatStar, for use in flotation circuits. Instead of controlling levels separately in each unit, the controller monitors levels throughout the circuit. It can thus take account of the global effects of any control actions. A collaborative project between Mintek and Karee Platinum Mine has begun, looking at aspects of flotation control. Karee plant was chosen as the site for this work because of its good existing control infrastructure. As a first stage of the joint project FloatStar was installed. Analysis during installation and running of the FloatStar has illustrated how circuit design and measurement technology can affect process control. Severe interactions have been observed in the levels of adjacent banks. The effect of FloatStar on flotation performance was tested and an improvement in level control was observed. Similarly, a faster settling of the plant after start-ups was observed. Both the improved level control and faster start-ups lead to higher platinum recovery.

Jan 1, 1999