Search Documents

By K. Bruce Hodgins

The North American mining industry faces challenging emissions regulations in coming years with the introduction of new standards for off-road diesel engines. In order to remain competitive, industry stakeholders must invest in new technologies that are economically and environmentally sustainable. Westport Innovations Inc., of Vancouver B.C. has developed high pressure direct injection (HPDI) technology that allows diesel engines to run primarily on natural gas with no intrusive engine modifications, reduced emissions of NOx, PM, and CO2, with no loss in performance. This is accomplished through late-cycle high-pressure injection of natural gas directly into a diesel engine combustion chamber. The natural gas is injected at the end of the compression stroke. A small amount of diesel fuel is injected first to initiate combustion, followed by the main natural gas fuel injection. The diesel cycle and its operating characteristics are fully retained including high combustion efficiency, low speed torque, high-power output, no engine knock and fast response to load changes. Natural gas has not been an attractive fuel alternative in mining operations due to reduced performance associated with spark ignition engines and the added weight and space required for compressed natural gas tanks. However, liquefied natural gas (LNG) can be stored in a similar manner and volume to diesel fuel by virtue of its increased energy density over compressed natural gas. Cummins, Inc. of Columbus, Indiana and Westport have formed a joint venture, Cummins Westport Inc. (CWI), under which agreement the HPDI technology is being applied to a Cummins QSK engine series for high horsepower applications such as mine haul trucking. CWI, along with Komatsu Mining Systems, ENRG Fuels, Placer Dome, and Cortez Joint Venture are performing a feasibility study for the development and demonstration of an LNGfueled HPDI QSK engine in a large mine haul truck. The goal would be to demonstrate low emissions consistent with EPA ?Blue Sky? standards, high efficiency based on HPDI technology and good economics resulting from the high fuel consumption of 2,000+ hp trucks.

May 1, 2002

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

By Brenda J. Wolfe

Following successful laboratory and pilot plant investigation of dewatering characteristics of molybdenum concentrate produced by a Chilean copper/moly producer, two (2) DENVER SALA 500 Series Tube Press Filters were installed in 1994 to handle the total production volume. Moisture requirements in the filter cake have been consistently met, eliminating the need for thermal drying after filtration. Operating data and Tube Press Filter are described herein.

Jan 1, 1995

By L. Thompsen

High pressure grinding has been introduced into many grinding applications. The high pressure grinding roll offers capacity increases of existing plants and savings in operating costs. Also metallurgical advantages could be achieved. The first high pressure grinding roll in a copper mine was commissioned in Arizona in July 1995. This paper provides information about the operating experience gathered during the first months of operation. The current flowsheet will be described as well as further options for plant arrangements.

Jan 1, 1996

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore, gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore , gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

By Hassan Ghaffari

? HPGR Process/Overview ? HPGR vs. SAG ? The Manufacturers ? Mine Operations using HPGR ? Projects by Wardrop/Tetra Tech ? Economic Benefits ? Questions Main Operating Parameters ? Press Force (N/mm2) ? Roll Speed (m/s) ? Moisture Content (%) ? Feed Particle Size Distribution Specific throughput M* = throughput/D*L*V (ts/hm3) Flake thickness/strength in balance with the compressing force (floating roll situation)

Aug 1, 2013

High pressure grinding technology has gained further interest in various industries. So far in the mining industry, machines are in operation in diamond mines and iron ore applications. In gold and copper ore processing, test work has been conducted showing considerable operational and process benefits. Similar benefits can be expected from HPGR applications in the platinum industry due to the preferred ore breakage along grain boundaries, thus liberating the PGE particles. This paper will provide an update on the state of high pressure grinding roll technology. Developments in the design of high pressure grinding rolls, for minimized maintenance requirements and availability just as high as conventional mills, will be presented. Plant flow sheets and concepts will be discussed, which allow for a reduction of capital and operating cost in comparison to existing two-stage milling circuits.

Jan 1, 2004

High pressure grinding rolls have found widespread acceptance for cement processing, and are now making their debut in the metalliferous minerals industry. Significant energy and wear material savings appear achievable in many applications. This paper re- views the technical literature on this important, emerging technology.

Jan 1, 1997

By I. Dunlop, A. Goulsbra, R. Dunne

Mineral liberation or more aptly the particle size at which cost effect liberation is attained is an important mineral processing parameter. This implies that not all the mineral is liberated as further size reduction is not economically warranted. For ores of low grade minimising both the comminution capital and operating costs are crucial aspect to ensure project visibility. As a consequence the focus of attention for the most part is direct­ed to 'coarsening the grind" ahead of any downstream process­ing treatment. In most cases, recovery will be sacrificed to pro­vide for 'more tonnes' of capacity and in general this is eco­nomically justifiable. Preferential liberation and its measurements is an aspect of mineral processing that has created much attention and contro­versy. It is not the purpose here to discuss this matter in depth other than to state in broad terms that if an ore from the same source is subjected to comminution by two different methods, such that the product particle size distribution is similar, and subsequent downstream treatment demonstrates substantial dif­ferences in recovery, then there is reason to believe that prefer­ential liberation has occurred. Comminution by high pressure grinding rolls (HPGR) is a relatively new technology claimed to have two major advan­tages over conventional comminution. Firstly and more impor­tantly is the ability to improve comminution power efficiency. Power reductions of 10 to 40 percent being claimed. (Pagett et al (1995), Sargent (1995)). A secondary benefit claimed is that preferential liberation can occur. Generally, for HPGR there is a natural tendency of the product to have a skewed particle size distribution to the finer size. This in its own right could manifest itself in improved leaching and preconcentration performance. The question remains that if in using another comminution device, other than a HPGR, to produce a similar product size distribution as the HPGR, will there be any difference in downstream between the products from this and a HPGR.

Jan 1, 1996

By Pura Alfonso, Sarbast Hamid, Hernan Anticoi, Eduard Guasch, Josep Oliva

"Av. Bases de Manresa 61-63, Manresa (08242) Barcelona, SpainTantalum is a strategic metal and an improvement of the mineral processing is an important issue. The main objective of this work is to optimize the grinding technologies for tantalum ores with high pressure grinding rolls. The selected ore for this study was an altered leucogranite from the Penouta Open Pit Mine (NW Spain). In the present work mono-size experiments have been carried out using grinding rolls with controlled pressure. The particle size distribution has been monitored in the input and output of the high pressure grinding rolls for each experiment. The cylinder pressure that is transmitted to the particles has been determined. New population balance models are presented for high pressure grinding rolls with parameter adjust for tantalum ore. The obtained model uses the physical description of particles under the comminution action of the grinding rolls. The obtained results are in agreement with other models and the errors in the adjustment are low. The selection function proposed for this model describes adequately the breakage probability of the particles inside the high pressure grinding rolls. The presented model can be a good alternative for simulating a high pressure grinding roll process. INTRODUCTIONTechnology for grinding have been improved for many years, introducing new variables and parameters involving energy consumption, mechanical stress analysis of the compression particles or pressure application for optimizing the comminution (Morrell et al, 1997). High pressure grinding rolls is a modern technology that is proven to reduce the operating costs in full scale plants when compared with other milling technologies. Its benefits on energy saving and simplicity in the process have been studied and applied, first in the cement clinker industry (Abouzeid & Fuerstenau, 2009) and after in mining activities, especially in metallic ore deposits (Austin et al, 1991; Guevara & Menacho, 1992; Morrel et al, 1997; Torres & Casali 2009; Numbi & Xia, 2015). Many author structures of the High Pressure Grinding Rolls modelling in three main branches; (a) throughput modelling, (b) Power and energy model and (c) particle size distribution modelling (Austin et al, 1991; Guevara & Menacho, 1992; Austin & Trubelja, 1994; Morrel et al, 1997; Torres & Casali, 2009)."

Jan 1, 2016

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By Gabriel Barrios, Juan Pérez-Prim, Marcelo Tavares

"The application of High Pressure grinding Rolls (HPGR) has been growing in the mining industry for the last 10 to 15 years. The major benefits generally supporting this trend are better energy efficiency, improved grinding capacity, less sensitivity to ore grindability variations and higher metal recovery in downstream processes such as heap leaching and flotation. The HPGR machine comprises a pair of counter-rotating rolls mounted in a sturdy frame. One roll is fixed in the frame, while the other is allowed to float on rails and is positioned using pneumohydraulic springs. The feed material is introduced in the gap between the rolls and is crushed by the mechanism of interparticle breakage. Comminution performance is largely determined by the pressure exerted on the bed of particles by the floating roll hydraulic system. The operating bed pressure depends on the hydraulic system start-up parameters and the loading response of the feed material. The work describes how the coupling of the multi-body dynamic simulation with Discrete Element Method in which particle breakage is described using the particle replacement method, can be effectively used to predict the performance of the HPGR. The model considers important variables as the HPGR rolls geometry and design, the hydraulic spring system start-up parameters and the material loading response, to describe operational key outputs as material throughput, operating gap and roller pressure distribution. The preliminary version of the model has been used to predict the effect of material properties on the operating gap and the load distribution on the surface of the rolls, demonstrating that it can describe qualitatively the HPGR operation, indicating that the model will be a power full tool for the simulation and selection of industrial HPGR units."

Jan 1, 2014

By Kellerwessei H, Oberheuser G

A major breakthrough in extending the life of the wear material of high pressure roll crushers when treating moist, highly abrasive material has removed the last impediment to the widespread acceptance of high pressure comminution in the minerals industry. The system is very energy efficient. It has been demonstrated that in the cement industry energy savings of up to 50 per cent have been achieved compared to conventional hall milling. Besides being energy efficient, the process provides some remarkable and useful effects; ò better liberation of mineral constituents (as proven for diamond liberation). ò preferential comminution where induced micro fissures follow grain boundaries. ò higher reactivity of the product due to micro fissures. All these points will be described here together with a review of current flowsheet design and incentives for the use of this method of Comminution.

Jan 1, 1993

High Pressure Sulfuric Acid/Oxygen Leaching of Platinum Group Metals Bearing Ni-Cu Mattes The processing of platinum bearing Ni-Cu ores for the extraction of platinum group metals (PGMs) involves comminution, flotation, smelting, and converter treatment of the furnace matte. Leaching circuits are predominantly used for further processing to separate the base metals and PGMs contained in the converter matte. Nickel dissolution is primarily achieved in the first stage leach (high pressure or atmospheric leaching, or a combination of the two), which is followed by second stage high pressure sulphuric acid/oxygen leaching to dissolve copper and the remaining nickel. PGMs are recovered from the leaching residue in downstream processes, and their dissolution in the first two leaching stages must hence be limited. Studies have been conducted to investigate the leaching mechanisms and kinetics of base metals in different leaching environments. The key operating parameters that influence the leaching kinetics of these metals include the temperature, acid concentration, degree of agitation, feed particle size distribution, and oxygen partial pressure. There is, however, a limited understanding of the behaviour of PGMs in the high pressure leaching process. Consequently, this process is controlled based on operators' intuition despite its importance in the recovery of PGMs. An improved fundamental understanding of the behaviour of PGMs in this leaching environment is required to be able to accurately model the process. This in turn will allow the development of an improved control strategy and the estimation of optimum operating conditions. An overview of the leaching mechanisms of base metals and the effects of key operating parameters on their dissolution kinetics in different leaching environments are presented. Models that have been developed to predict the leaching behaviour of base metals are discussed and evaluated. Finally, initial results obtained with an experimental setup that will be used to investigate the behaviour of PGMs in high pressure leaching systems are discussed and compared with published results.

Sep 13, 2010

By Sam Palombo, James José Varela

"Washing can be defined as the process used to eliminate or reduce the dirt (presence of fines or slimes) of one material. It is also the basic and oldest process applied to ore preparation for further concentration. This process, in combination with commnution and screening, form the so called washing plant and in many cases produce end products. This work describes the factors that influence the performance of the washing process and main washing technologies used in the mineral processing industry.The Hydro-Clean represents, since 1998, a state of the art technology in this area and is comprised of one of the most innovative solutions developed at HAVER & BOECKER. HAVER & BOECKER design and manufacture technology for mining and related industries. Today the Hydro-Clean is manufactured and sold throughout the Haver Screening Group (HSG) which is comprised of HAVER & BOECKER Maschinenfabrik Münster, HAVER & BOECKER Latinoamericana – Brazil and W.S. Tyler Canada.The Hydro-Clean is a washing technology based on utilization of high pressure water jets. To follow we will discuss how the Hydro-Clean’s different modes of operation result in several advantages related with mine waste reduction, recovery of saleable product, lower capital costs, superior washing results, less stress for the material, a wider range of application and less maintenance cost. Aside from these positive factors, its lower operation costs related to the consumption of energy and water are presented. It is important to note that the quantities, tonnages, data and management concepts presented in the paper are accurate for the time of writing and are subject to change and modification as operations progress."

Jan 1, 2009

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976

By Robert A. Jankowski, Charles Babbit, Natesa I. Jayaraman

The Bureau of Mines, together with Foster Miller Inc., has developed a compact, high pressure scrubber system for continuous miners. Powered by water energy alone, it can move up to 1.4 m3/s (3,000 cfm) of air and scrub a significant amount of the dust in the air. Full- scale model and underground trials showed excellent performance. Operated at 8.3 x 10[3] kPa (1,200 psi) and 38 L/m (10 gpm), the scrubber has reduced operator and return dust concentrations by more than 50 pct. This paper describes the full-scale model development, system fabrication and underground evaluations of this novel and inexpensive scrubber.

Jan 1, 1989

By Norm Steenson

Rapid excavation includes rapid support and is the central theme of this paper. Over the last few years, enormous strides forward have been made in the excavation and material handling aspects of underground excavation. However, the technology necessary to support these rapidly created openings has lagged behind the other aspects. This paper would attempt to bring you up-to-date on the progress made in bringing ground support using shotcrete into the same productivity rates as the other cyclic operations. Shotcrete has become an acceptable material for temporary and permanent support for undergound openings. However, coarse aggregate shotcrete has been an expensive construction material. It has been confined in the main to difficult ground conditions where conventional methods of support have proved to be even slower and more expensive than shotcrete. There are two main factors influencing the productivity of shotcrete equipment. (1) Structural shotcrete as opposed to gunite requires 40% to 45% rock minus 3/4" in the mix design. The equipment to handle such aggregate content has been difficult to develop on a volume basis owing to the attritional nature of the material which causes intense wear problems on

Jan 1, 1974