Search Documents

By Yun Guo, Min-Min Lin, Bing Xie, Hong-Yi Li

The extraction of vanadium from vanadium-containing APV-precipitated wastewater by W/O microemulsion system was studied. In the N263/n-heptane/isoamyl alcohol/NaCl microemulsion system, N263 played double functions of cationic surfactant and extractant to form microemulsion in n-heptane, and isoamyl alcohol was added in the microemulsion as a cosurfactant. The extraction of vanadium by W/O microemulsion systems effectively accelerated the extraction and improved the extractatability because of the enormous increase in the micro-interfacial surface area. Due to ion association with extractant, vanadium was extracted into the microemulsion phase. The influence of different parameters on the extraction ratio (E%) were investigated, including the volume ratio of aqueous phase to microemulsion, surfactant concentration, pH value of the feed solutions, cosurfactant concentration, extraction time as well as temperature. In optimum conditions, the extraction ratio (E%) can reach 97.2%.

Mar 1, 2018

By Georgios Kolliopoulos

Water is a critical commodity of our generation and a key compound for the chemical and mining industries. Sustainable industrial development is directly associated with the ability to recover clean water from contaminated sources. Forward Osmosis (FO) is a low-energy footprint membrane process allowing the recovery of clean water from high salinity effluent streams. In FO, water is recovered spontaneously into a concentrated draw solution (CDS). Energy is required to separate the recovered water from the resulting dilute draw solution (DDS). In the current work, the fundamentals of the FO process and the most important aspects affecting its performance are discussed. An energy comparison of FO and conventional water recovery technologies is presented. Finally, the opportunities FO presents in the field of hydrometallurgy are analyzed.

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By Hassan Saalman, Mahmoud Mahmoud, Omneya El Hussaini

The Ferruginous sandstone ore was obtained from Ramlet Hemeyir area, Southwestern Sinai, Egypt, was found to contain 10% rare earth elements (REE). A representative sample has been subjected to sulfuric acid agitation leaching. About 93% of the REE content was released by mixing the ground sample to -100 mesh with concentrated H2SO4 at solid/liquid (S/L) ratio of 1/2 for 5h at a temperature ranged from 250 to 300o C. The REE was precipitated from the prepared sulfate leach liquor of pH 1.0 by adding 35% oxalic acid at 25o C. The precipitation yielded 98% REE. For selective separation of yttrium, the rare earth cake was leached with 31.5% nitric acid. Next, the aqueous solution was contacted with di-(2-ethylhexyl) phosphoric acid (D2EHPA) where 98% yttrium extraction was achieved. Stripping was done with hot H2O (80o C). Finally, a precipitation with oxalic acid was done followed by ignition at 950o C. A yield of 95% yttrium oxide was produced.

Jan 1, 2014

By Hsing Kuang Lin

Extraction of zinc from chloride solution with dibutyl butylphosphonate (DBBP) in Escaid 110 has been investigated. The distribution coefficient of zinc was found to be independent of equilibrium pH. This independence indicates that the mechanism of the extraction may be solvation. Slope analysis for the system of dilute zinc chloride solution reveals that two moles of DBBP react with one mole of zinc. A series of tests were conducted to bring DBBP to its full loading capacity and the analysis of the results confirms this stoichiometric factor of 2. Extraction isotherms were established by varying either the AIO ratio or the concentration of zinc in the aqueous feed. Both curves were found to be identical.

Jan 1, 1990

By Xudong Liu, Ganghua Fu, Yufeng Guo, Wei Chen, Yujia Tan, Tao Jiang

Willemite is usually found in high-silicon oxide zinc ore and zinc metallurgical secondary resources but without effective extraction method yet. In this study, zinc was extracted from willemite by sodium salt roasting and ammonia-leaching process based on the idea of zinc phase reconstruction. The effects of Na2CO3 dosage, roasting temperature and roasting time on phase transformation and zinc leaching rate were studied, respectively. The results show that Zn2SiO4 was transformed into ZnO or Na2ZnSiO4 during roasting process. After roasting at 800 °C for 2.5 h at ratio of n(Na2CO3)/n(Zn2SiO4) = 2.5:1, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.62% in NH4Cl–NH3–H2O leaching system, which increased by 91.57% compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl–NH3–H2O system.

Mar 1, 2017

By J. Bai, C. Zang, W. Yuan, L. Zhuang

"This study evaluates the efficiency of using mechanochemical reduction to assist the extraction of zinc from zinc ferrites by alkaline leaching. The transition of zinc ferrite into a metastable state after mechanochemical reduction with metallic iron contributes to the ready dissolution of zinc from the activated zinc ferrites in alkaline solution. Zinc ferrites were mechanochemically reduced under conditions of Fe:ZnFe2O4 mole ratio of 2:1, using 5 mm diameter stainless steel balls as the activation medium at a mass ratio of balls to raw materials of 25:1. Subsequent leaching in 6 mol/L NaOH solution at 90°C resulted in more than 70% Zn extraction. These results may be used to further develop a hydrometallurgical process for recovering zinc from zinc ferrites in alkaline solution.IntroductionZinc is an important nonferrous metal required for various applications in batteries, solder, dielectric materials, and piezoelectric materials. High-grade, easily concentrated ores are becoming scarcer: to meet world demands for zinc, it is necessary to develop economical and environmentally safe metallurgical technologies that use secondary materials such as leach residues of roasted zinc concentrates and electric arc furnace dusts. The zinc in the majority of these wastes occurs in the form of zinc ferrite (franklinite, ZnFe2O4), which is very stable and insoluble in most acidic and alkaline solutions (Langova and Matysek, 2009; Youcai and Stanforth, 2000).Several pyrometallurgical and hydrometallurgical processes (Jankovi et al., 2014; Langova and Matysek, 2010; Morcali et al., 2012; Shawabkeh, 2010) have been proposed for the treatment of zinc ferrites. Pyrometallurgical methods are costly owing to high energy consumption and their emissions of toxic gases are considered an environmental problem; hydrometallurgical methods are preferred for process economy and environmental reasons (Copur et al., 2004)."

Jan 1, 2016

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By K. Saberyan

In this study the extraction of zirconium and hafnium has been investigated by solvent extraction using Cyanex 302 in various media such as nitric, sulfuric and hydrochloric acid has been investigated. Effect of various parameters such as type and acid concentration, extractant concentration, type of diluent, equilibrium time, various foreign ions and finally type and concentration of strip-ping agent have been studied. The results showed that nitric acid was optimum media for extraction of zirconium and hafnium. The extraction of zirconium and hafnium occurred quantitatively in the concentration of higher than 4 M nitric acid but in hydrochloric acid media, quantitative extraction obtains over 8 M HCl. In sulfuric acid media, extraction of zirconium and hafnium is negligible. Stripping studies showed that the optimum reagent for stripping was 0.5M sulfuric acid.

Jan 1, 2014

By R. Schuhmann, A. M. Gaudin, J. Dasher

Occurrrences of South African uranium have been known qualitatively for over twenty years, but no account was taken of them because of their low grade. In 1945, known uranium deposits were few, but their grades were 20 to 100 times higher than South African ores. Viewed in this light, the exploitation of South Africa's uranium is revolutionary indeed. Development of various analytical procedures capable of dealing with the needs of the project accounted for one-half of the cost and included: a) simple and automatic radiometric analytical procedures, b) sampling procedures appropriate to prevent sample contamination, c) procedures for sample and record-storing to accommodate many thousands of analyses per month, d) chemical methods giving high accuracy analyses for high grade samples not at radioactive equilibrium, and e) development of rapid procedures having moderate accuracy for low grade samples i.e., mill tailings and barren liquors. This task is continuing today with major improvements coming from time to time.

Aug 1, 1956

By James A. Barclay, Ralph C. Kirby

The US minerals posture will be increasingly dominated by three interrelated factors. First, when viewed over the long range, the US supply situation can be expected to steadily deteriorate as demand increases. Domestic high-grade ores have been used up, and other nations compete with the US for world supplies. Second, as environmental awareness becomes more acute, an aroused citizenry is demanding that minerals industries conform their operations to rigorous new standards. Finally, the changing energy situation that confronts the US is forcing an appraisal of energy-use patterns on operations previously guided solely by economic principles and not by national priorities. While future US mineral production and consumption patterns are unclear at this time, it is certain that US demand for minerals will continue to outrun domestic supply. Thus, the US is faced with a challenge of producing more minerals and metals from lower grade resources. Meeting this challenge means a strengthening of US research and development efforts, coupled with their application in the remaining leadtimes available. Some specific examples of how the US Bureau of Mines (USBM) is assisting in the processing of low-grade resources follow.

Jan 6, 1975

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001

By Guozhi Lyu, Ting-an ZHANG, Biyu Long, Yajing Tian, Xuejiao Cao, Weiguang Zhang

Aim to the separation problem of high concentration V–Fe in stronger acidic leaching solution of vanadium slag, a novel chelating extraction system is proposed to separate V and Fe. Influence factors including initial pH value, the extractant concentration, the phase ratio, temperature and time are investigated. The experiment results show that single extraction rate of V and Fe reach 85.57 and 0.39% respectively, when pH value is −0.4, organic phase composition is 30% Mextral 973H + 70% sulfonated kerosene oil, O:A = 1:1, stirring time is 10 min, extraction temperature is 30 °C. The industrial experiment results of three levels countercurrent extraction show that the total extraction rate of vanadium and iron can reach 97.44 and 0.23%, separation factor is 6410. The effective separation of V and Fe in high acid and high iron solution can be accomplished.

Mar 1, 2018

By Zuomei Jin

The Mineralogical form of Silver in a Ag-rich complex ore was determined. In the complex sulfide ore, acidic thiourea leaching resulted in 35% extraction of silver directly. In the same complex sulfide ore, under the effect of ultrasonic treatment, 65% of silver can be ex¬tracted. After the above ore had been roasted and acidically leached of Zn and Cu, the silver extracted from this Pb-Ag residue was 96.8%. The effets of temperature, thiourea and ferric ion concentrations and partical size were examined. The leaching rate of silver from the Pb-Ag residue was diffusion controlled. The activation energy was calculated to be 10. 49%KJ/mole. The kinetic model for the thiourea leaching of silver from Pb-Ag residue was obtained and is given by, The kinetics of silver cementation by aluminium in thiourea solutions was also investigated. The activation energy was calculated to be 65. 13KJ/mole, which is reasonable fora rate-limiting surface reaction.

Jan 1, 1995

By Browning E. J

The application of conventional dust control systems in British Coal mines has considerably reduced the incidence of pneumoconiosis. A number of new techniques have been developed involving extraction close to the cutting heads of mining machines which will be capable of controlling airborne dust with the greater intensity of production necessary in the present economic climate.

Jan 1, 1988

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Jin-Young Lee

"Global population is a key factor in future energy requirements, especially considering the important elements of global energy resources, electricity production, the accessibility/non-accessibility of electricity, greenhouse gas emissions and the states of nuclear reactors. Everyday human requirements depend on industrial products, and industries need a considerable amount of electricity to run. Nuclear fuel is inexpensive and bolsters industrial growth. As uranium reserves are being consumed rapidly, an alternative source of energy in the nuclear industry is thorium. Here, primary energy supplies by various sources from 1993 to 2011 as well as estimates of future needs to 2020 are discussed. This study finds that primary energy sources are mainly fossil fuels, renewables sources, and nuclear and hydro energy. In addition, growth depends on increases mainly in renewable sources.Recovery of thorium from its ores by using hydrometallurgical routes were described and discussed. The final part of this paper was presented a case study of the thorium extraction from Korean monazite ore leach liquors by using Prieme JM-T diluted in A150 diluent as an extractant system. And possible separation of the thorium from rare earths (REs) and base metals were calculated by measuring of separation factors and finally, the recovery of thorium from loaded organic of Prieme JM-T was established.THORIUM IS FUTURE NUCLEAR FUEL?Global energy consumption is increasing everyday with the high population growth, high industrialization of numerous countries and the higher level of good and services consumption that follows it. If we look at specific sectors of the economy, oil consumption grew by 0.8 million barrels per day, globally, whereas the increase was 0.4 % for natural gas and coal 1.8 % for nuclear power and just under 2.0 % for hydroelectric power (Asheley 2009). Use of renewable sources of energy for power generation and transportation increased by 3% in 2014 (BP 2015)). Thus alternative source of energy must be identified and developed to meet this increasing demand. Thorium is a potential one for the nuclear industry."

Jan 1, 2016

By B Harvey

Achieving community and stakeholder endorsement during life-of-mine planning and implementation requires a business-connected approach, as opposed to charitable giving, disconnected offsets and environmental adventurism.CITATION:Harvey, B, 2014. Extractive companies, development and environmental agendas, in Proceedings Life-of-Mine 2014 , pp 19–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

As the title indicates the central themes discussed in this contribution are sustainable development, information systems, and extractive industry. More specifically, the objective is to present a prototype for the systematic generation of extractive industry (henceforth: EI) û specific sustainability information. The paper begins with the authorÆs viewpoints on the core notions of sustainability, and development, as well as their relationship to information. These set the stage for the introduction of the information system (IS), as well as the follow-up sustainability information system (SIS) extractive industry sustainability information system (EISIS) concepts and related discussions. The paper continues with a second part, in which, efforts to research and develop an EISIS prototype are described. First, the team is presented. Second, the systemÆs aim and target groups are briefly discussed. After, an articulated overarching EISIS conceptual model emphasising capital accumulation, and service flow concepts û is presented. This is followed by a detailed description of the assembled prototype with a focus on data and information generation. The formulation of data generation, storage and transmission processes, as well as its use in sustainability interpretation rules and their embedment in the conceptual model is made with respect to monetised stock and flow parameters, measured in the appropriate dimensions. In the third part, the author presents and discusses the results of a first round of prototype experimental development in three major EI firms. First, the system observation, and data analysis protocols are described. Second, a review of protocol implementation, and respective results, is made. Finally, the overall performance of the proposed prototype, and development process issues are discussed, before suggesting areas for improvement and future research. The paper ends with a conclusion in which the author provides a retrospective balance of the æknowledge creation projectÆ, as well as a prospective outlook for research in this field; before acknowledgements are made and references provided.

Jan 1, 2009

By Theophile S. Yameogo

Les ressources naturelles ont en général été le moteur du développement économique et social des nations. Les pays aujourd?hui développés sont pour la plupart d?anciens eldorado, charbonniers ou pétroliers. D?autres le sont toujours. L?Afrique fait cependant figure d?exception : même en étant comblé de ressources naturelles exceptionnelles, les pays de ce continent croulent sous le poids de la pauvreté et de ses acabits que sont les maladies, la famine, la guerre et l?insurrection sociale. On reconnaît néanmoins qu?il y a des cas particuliers comme le Botswana, la Namibie, l?Afrique du Sud. Face à cette situation, beaucoup de scénarii ont été proposés sans pour autant porté les fruits espérés. Le rapport Brundtland suggère que le développement durable est la clé du succès car elle veille à la prospérité économique, à l?équité dans la société et à la pérennité dans l?environnement. Pour l?Afrique, beaucoup de facteurs doivent être considérés et les solutions se doivent d?être pratiques et éthiques. Le futur ingénieur des mines qui a écrit ce rapport, apporte sa vision de la situation non sans avoir auparavant analysé les faits. Cette démarche, qui se veut avant tout éthique, inclut les aspects sociaux, économiques et politiques. Introduction In the 40s, 50s and the 60s, many economists, among which Harold Hotelling from South Carolina University, thought that developing countries could reach socio-economical success by extracting their natural resources such as oil and minerals. The current economical disaster seems to have contradicted that belief and critics like Davis Graham (Colorado School of Mines) and Michael Ross (University of California at Los Angeles) even suggested that extractive activities stop in Africa. But the experts of the World Bank (Mining Department) and some mining and oil companies are committed to reverse the tendency by implementing a new approach. Considering the principles of sustainable development defined in the Brundtland report (1987), we decided to analyze the possibility of giving the extractive industry a catalytic role in creating a socially, economically and environmentally development in Africa. In other words, can we continue to mine and extract oil in Africa for its blossoming future under the ruling of the sustainable development? In the following, we start by explaining the African socio-economic and political context. After a brief definition of the sustainable development, we explain why, for Africa, some believe in the extractive industry and some don?t. In the end, we draw out conciliatory arguments.

Apr 1, 2005

By S. W. Ross

In 1936 a description of the plant (Fig 1) and process employed by the Electrolytic Zinc Co. of Australasia Ltd. for the recovery of zinc from zinc concentrate by the electrolytic process was prepared. † During the twelve years which have elapsed since the preparation of the earlier paper, several major changes in the metallurgy of the process have been introduced. It is the purpose of the present paper to give a general description of these changes and thus to bring up to date the description of the plant and process. Summary The major changes in Risdon practice since 1936 have been: 1. Replacement of two stage roasting by a preliminary roast followed by the flotation of all the leach residue and the roasting of the flotation concentrate. 2. Screening of all calcine fed to the pachucas. 3. Continuous leaching of calcine and improved classification of pachuca discharge. 4. Close control of hydrogen ion concentration during purification for iron removal. 5. Recovery of cobalt as a good grade oxide. 6. Production of part of the zinc output in the form of "four nines" metal (99.99 pct purity). 7. Closer spacing of electrodes thus increasing the potential output of cathode zinc per cell by 50 pct. Changes which are in prospect and for which construction work is proceeding at the present time involve the starting up of: 1. Two suspension roasters. 2. A contact acid plant to produce 150 tons‡ of acid per day and replacing the existing Mills Packard chamber plant. 3. Extra power station capacity to permit greater current flow to existing cell room units. This will increase the output of cathode zinc from about 245 to 290 tons per day. Plans for the future envisage the building of an ammonium sulphate plant, the first unit of which will produce about 50,000 tons per year, and improved treatment of zinc plant residue for the recovery of zinc, lead and other metals. At the end of this paper tables of metallurgical data are presented relating to the year ending June 30, 1948. Details of Changed Practice Output In 1936 the production of cathode zinc amounted to about 200 tons per day. This has since been increased to about 245 tons per day while plant extensions are practically complete which will permit of an output of about 290 tons per day in the near future. Roasting Division ROASTING POLICY A major change has occurred in the roasting policy. Twelve years ago the method in use was to carry out a two stage roast in the first stage of which sulphide sulphur was reduced to about 6 pct. The pre-roast calcine was re-roasted in modified Leggo furnaces using coal as fuel, sulphide sulphur being reduced to about 0.8 pct. The whole procedure was described on pp. 482491 of the earlier paper. Although this roasting procedure had certain advantages it possessed some distinct disadvantages. For instance, it appeared uneconomical to heat up the entire input of pre-roast calcine to roasting temperature by the expenditure of fuel in order to oxidise a few percent of sulphide sulphur. It was argued that if the pre-roast calcine were leached and a process could be developed for the recovery of a zinc sulphide concentrate from the leach residue, this concentrate, small in weight compared with the pre-roost calcine, would probably roast autogenously, thus virtually eliminating the expenditure of fuel as well as greatly increasing the weight of sulphur oxidised per square foot of furnace hearth area. The obvious method of producing a suitable concentrate from leach residue was by flotation. It will be recalled (see p. 495 of the earlier paper) that when two-stage roasting was practised the leach residue was classified, the granular fraction was ground and floated while the slime fraction was thickened, filtered and dried ready for shipment to a lead smelter. This process worked quite successfully. However, when trials were made of leaching a calcine carrying several percent of sulphide sulphur the granular fraction still floated well, but the slime fraction carrying 8-10 pct sulphide sulphur yielded very poor results when subjected to flotation. This fact held up the application of "pre-roast" leaching for many years. However, successful flotation of the slime fraction of leach residue was finally achieved and in August 1940 the slime flotation plant began operation, while the leach-

Jan 1, 1950