Search Documents

By J. Kolacz

"A new sensor based sorting system has been developed, providing a possibility for laboratory scale testing and further scale-up of the separation results to the industrial operation. The new system contains different sensors as: X-ray detectors, visible light cameras, NIR cameras, ultraviolet cameras and magnetic sensors, in the same sorting unit. The sorting unit allows advanced calibration options and fine-tuning of the installed sensors to achieve the best separation effect under controlled conditions. Finally, the processed material can be analysed and separated by the rejection mechanism, similarly to the industrial scale operation. At the same time, the process is carried out with limited amount of material allowing detailed statistical calculations for processed particles and all sensor types. The optimal settings and sensor types are specified for the industrial application.The paper describes the scale up of the results achieved for iron ore and coal, where the test work was first carried out using the new laboratory sorting system and where the industrial scale sorting system has been built, in the final stage. The industrial scale sorting results showed a very good correlation between the laboratory and full scale operation. Thanks to the detailed study carried out in the laboratory equipment, the settings of the sensors in the full scale operation provided much better separation efficiency. It was especially important to provide proper setting for the X-ray sensor data calculations, which can be very critical for achieving the best results. During the industrial scale sorting of coal, the input material had 40-55% rock particles as the direct source of ash in the coal stream. The optimal laboratory unit settings and transferring these settings to the industrial sorter, provided 98.8% efficiency for removing rock particles with only few % losses of coal."

Jan 1, 2016

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

Steel slag is an industrial byproduct of steelmaking that is mainly composed of calcium, iron, silicon and magnesium. In addition, depending on the different raw materials entering the furnace, steel slag contains a certain amount of vanadium that is the main source of vanadium production, accounting for 69 percent of the species of the total vanadium raw material [1]. From experience, the production of one ton of steel will generate 1.0 to 1.5 tons of steel slag [2]. However, the utilization efficiency of steel slag is less than 30 percent, and a large amount of steel slag is identified as waste and stacked in tailings. The random stacking of steel slag not only wastes large amounts of limited steel and land resources but also exerts pressure on the environment [3], making it imperative to research the effective utilization of steel slag and recycling of metal resources.

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

This study presents a method for recovering valuable metals and synthesizing anhydrite from steel slag using sulfuric acid leaching and solvent extraction. The process achieved high leaching efficiencies for V, Ti, Fe, and Mg, and produced anhydrite with 93.09% purity. The leachate was further processed to separate and recover V, Ti, Fe, and Mg using selective stripping and precipitation methods, offering a sustainable approach to steel slag utilization.

Jan 22, 2022

By Xun Zhang, Hang Qiu, Andrea R. Gerson4, Shaomin Lei, Yubiao Li, Yu Meng, Zhenyu Pei, Min Lin

Efficient separation of trace muscovite from the surface/interface of quartz grains was accomplished during oxidizing calcination and catalytic pressure leaching of the hydrothermal quartz. Experimental results suggest that 98.97% or more of the muscovite was separated when quartz sand was calcined at 900 °C for 5 h and then leached by hydrochloric acid and ammonium chloride solutions as substitutes for leaching agents containing fluorides. The chemical processing techniques show high selectivity in purifying quartz sand by transforming mineral muscovite into active structures during oxidizing calcination, and then dissolving the active substances during catalytic pressure leaching

By Jason Buenker, Molly Winston

Torque-installed piles are gaining popularity in Southern California as the go-to deep foundation element for small- to medium-capacity loads in urban environments. The torque-installed pile is a displacement- based screwed pipe pile with a closed-end conical tip welded to the bottom of the pipe. Torque-installed piles are most efficient in loose to medium dense soils with high liquefaction potential. Where used properly, torque-installed piles can be installed faster, require less clean-up, and create less onsite vibration/disturbance than other pile alternatives. However, torque-installed piles are not applicable in all soil conditions and care must be used to apply the pile effectively in the correct subsurface environment. This paper will review current Southern California state-of-the-practice for torque-installed pile design and construction, potential roadblocks to successful installation, and available capacities from load tests. INTRODUCTION Torque-installed piles are a type of full-displacement screwed pipe pile originally developed in Southern California circa 2001 by Substructure Support, Inc. The pile is unique for its proprietary closed-end conical tip shown in Fig. 1. The tip has a welded steel-helix plate and cutter teeth that allow the pile to be advanced efficiently under applied torque and down pressure (crowd). Since original development of the pile, several contractors or manufacturers have proposed similar proprietary screw-type piles with comparable conical tips. Pile installation is relatively quiet, vibration-free, does not generate spoils, and faster than comparable pile types. The pile was originally developed as an alternative to driven pile foundations and remains a critical substitute to driven foundations in urban environments. Torque-installed piles are conventionally specified as 12 ¾-inch outside diameter (OD) steel pipes with a ⅜-inch-thick wall, although larger sizes with alternative dimensions have been used outside Southern California. Pile installation lengths generally range from 30 to 50 feet but may reach 80 feet or greater where soil conditions permit. The pile is generally backfilled with concrete following installation to increase lateral pile stiffness and may incorporate rebar cages or other reinforcing steel to facilitate connections to structural elements. The pile is frequently specified using performance-based specifications that encourage contractor innovation and use of proprietary installation means and methods.

Jan 1, 2019

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By L. W. Saperstein, MJ. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives fly ash, bentonite, and portland cement were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three offered some increase in the ultimate strength of the backfilling mixture. However, portland cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1990

By M. J. Carlson

With the goal of improving the strength characteristics of pneumatically emplaced material used for localized subsidence control, the binding additives: fly ash, bentonite, and Portland Cement, were examined for their effect on the support capabilities of coal refuse. It was found that, within certain concentration ranges, all three of them offered some increase in the ultimate strength of the backfilling mixture; however, Portland Cement gave the greatest percentage increases. Selection of the appropriate backfilling mixture will allow for the most economical and efficient subsidence control when pneumatic stowing is employed.

Jan 1, 1987

Escalating energy and electricity costs have become one of the largest drivers of expenditure in mining operations. Over the last eight years, energy costs have tripled when expressed as a percentage of total expenses in South African mines. In an effort to manage and reduce electricity costs, energy management strategies can be developed, inefficient operating units replaced, and the operation of energy-consuming components of ventilation systems optimized. Power consumption on mines is controlled mainly by three strategies, namely load clipping, by which energy use is reduced for certain parts of the day; load shifting, by which energy use is shifted to other parts of the day; and energy efficiency, by which energy use is reduced permanently. In this paper several projects that were implemented using the first two strategies of load clipping and load shifting are investigated. The actual and potential savings that can be achieved by implementing such energysaving interventions are presented. To reduce the operating costs of ventilating and cooling underground mines permanently, system optimization studies must be completed. Methods that can be used to reduce energy usage by optimizing cooling and ventilation systems are described, and network simulation models that accurately reflect the current and planned ventilation conditions are discussed. These models are then used to examine various options for improving the overall ventilation and cooling strategy. Different optimization scenarios can be simulated, and this assists the design engineer in obtaining the most energy-efficient system that will satisfy design workplace conditions. The final outcome is a reduction in operating costs, which can result in better operating margins and an extension of the life of mine.

Jan 1, 2014

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Vaughn Bowns, Allen Stanley, Brian Redeker

"Running casing in drilling operations is often complicated by boulders or large cobbles.Past practices of dealing with these have included use of drop hammers, attempts to drillthrough or around the boulder, contact explosive charges and even pulling the casing andrepositioning the hole. All these methods are time consuming, expensive and offer noguarantee of success. In this paper a different method of dealing with these boulders ispresented that promises to be faster and less expensive with a much higher success rate.This involves using a light plastic conduit pipe to place a shaped explosive against theboulder. It requires no special tools or techniques not commonly in use in the drilling andblasting industry."

Jan 1, 1993

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By Matt Kilburn, Liming Lu, Steve Suthers, Alexander Edenton, Rodney Smyth, Matt Adam

"Magnetite concentrate is naturally good for pelletising. However, due to the depletion of reserves of traditional high grade hematite iron ore worldwide, the usage of magnetite concentrate in sintering is expected to increase substantially. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. This will not only improve the quality of agglomerates produced, but also have a potential beneficial impact on the fuel consumption of the agglomeration process. There are an increasing number of magnetite projects currently being considered and developed. However the concentrates from some of these projects are too coarse as pellet feeds and much finer and denser than normal sinter feeds. Accordingly, special strategies are required in order to utilise the coarse magnetite concentrates at high proportions in pelletising and sintering. This paper discusses various raw material preparation technologies and blending optimization methods demonstrated to be effective for improving the sintering and pelletising performance of coarse magnetite concentrates. Pre-granulation and addition of binders, such as hydrated lime, were found to be particularly efficient in recovering the sintering productivity of sinter blends containing magnetite concentrates. In pelletising, HPGR (High Pressure Grinding Rolls) grinding enabled production of good quality pellets from 100% magnetite concentrates and optimized blends containing up to 70% magnetite concentrates also formed good pellets.INTRODUCTION Magnetite concentrates are often used as feed materials for pellet plants or sinter plants depending on their grades and grain sizes. To achieve the required quality of green and fired pellets, the concentrates often need to be ground very fine (80% passing 38- 45 m), which inevitably consumes a great amount of energy. Therefore, efficient grinding processes are required to reduce the amount of energy consumption needed to achieve the sizing and chemical specification of pellet feeds. The use of magnetite concentrates in sintering has the potential to improve sinter chemistry, which is deteriorating over time due to the slowly decreasing grade of direct shipping iron ores around the world (Yang and Mathews, 1997; Yang and Witchard, 1998, Yang and Davis, 1999; Yang 2005). However, methods are required to allow the utilisation of high levels of concentrates in sintering while maintaining productivity and sinter quality (Han and Lu, 2017)."

Jan 1, 2018

By F Mavroudis, M Gaastra

Due to the increasing demand for resources worldwide, efficient utilisation of raw material deposits and recycling technologies become more and more important. Growing industrial nations and increased living standards require a large raw material supply. Hereby responsible handling of existent primary and secondary raw materials is indispensable. By utilising state-of-the-art technologies resources are extracted, recovered and recycled more efficiently which increases sustainability. Hereby sensor technologies combined with intelligent data processing systems in particular provide a considerable research area. Innovative sensor technologies are already implemented during recognition of material-specific characteristics, during elemental recognition as well as during machine control. They are applied to attain increased automation levels of mining machineries, higher recoveries during mining and processing as well as higher recoveries. To be able to face the increased demand for sensor technologies and the integration into raw material industries, an interdisciplinary association of three RWTH Aachen University Institutes has been founded. The association has expertise on increasing productivity and capacity utilisations by automating mining and recovering processes by sensor technologies. Due to the utilisation of sensor systems, materials and structures can now be detected and elementary analysed on a real-time scale. The developed and enhanced techniques are the key for any ambition of autonomous plants and machineries. This paper gives an overview on the regarded sensor technologies for material recognition, machine automation and mineral processing. The authors present concepts based on extensive laboratory and field studies of successful implementation and application the technologies considering special mining conditions. Overall three applications are described to demonstrate the potential of sensor technologies for autonomous and sustainable mining: real-time analysis: recognition of elementary compounds during extraction processes; multi-sensor system EiControlPlus: designed for automation of longwall shearers by complete detection of the machineÆs environment; and sensor-based sorting: applied in recycling and mineralÆs industries.

Sep 26, 2011

By Gupta R. C

Direct reduction of iron ore by solid reducing agents have been studied extensively and summarised by several authors (Otsuka and Kunii, 1969; Abraham and Ghosh, 1979; Frauhan, 1977; Rao, 1971; Kawasaki, Sanscainte and Walsh, 1962; Ghosh, 1970; Rao, 1979). While studying the reduction behaviour, it is generally agreed that the reduction occurs via gaseous intermediate, generated by carbon gasification reaction which involves mass transfer, heat transfer nucleation and growth, etc through a) reduction reaction occurring at solid reductant, and b) reduction reaction occurring at solid iron oxides, thus making the overall reduction process very complex in terms of clearly defining the reduction kinetics of the system. In addition to this, practical difficulties like correctness of reaction temperature, (Seaton, Foster and Velasco, 1983) difficulties in isothermal temperature studies of reduction, difficulties in monitoring the reduction process while using gaseous reductants and separation of reduction by volatile matter from overall reduction process make the reduction kinetics more complex (Misra).

Jan 1, 1999

By W. Graham

"IntroductionEFFLORESCENCE is herein considered to be any deposit of salts on the surface of a masonry structure that is brought from within or through the structure by capillarity and deposited by evaporation. Usually, efflorescence is white although green, yellow, and brown efflorescence is sometimes observed.The common white efflorescence almost always consists of sulphates of the alkali and alkaline earth metals and calcium carbonate, although sodium chloride is frequently present in structures erected near the sea shore.The first and most obvious result of the presence of soluble salts in masonry is the unsightly accumulation of these salts on the surface. This is particularly noticeable early in its life and is frequently fugitive ( 1), as much of the salt is soluble and is gradually washed away by rain. This removal can usually be facilitated by scrubbing; the structure with dilute hydrochloric acid.A more serious effect is the continuous accumulation of soluble salts as a result of ingress of sulphur acids in rain water or water from the ground. This may eventually cause spalling and disintegration by crystallization of salts in the pores of brick and mortar. An example of this type of failure, resulting from the crystallization of calcium sulphate, is discussed by Hardesty (2). Butterworth (3) describes similar failure resulting from •crystallization of magnesium sulphate."

Jan 1, 1954

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I&apos;m not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I&apos;m using the term "battle" loosely because, in reality, it wasn&apos;t a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I&apos;d like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government&apos;s harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

&nbsp;Increasing concern about the impact of alluvial mining discharges on the water quality of some West Coast rivers lead to a joint West Coast Gold Miners Associate, Trade and Industry funded study by Water Technology (NZ) Ltd. The objective of the study was to assess the treatability of West Coast alluvial gold mining discharges and to develop simple treatment systems which could be effectively adapted to a variety of sites in the region. &nbsp; The approach was to apply standard water treatment techniques to field situations using low cost technology. Initially the various types of alluvial gold mining operations were identified then after preliminary site investigations and laboratory studies were carried out, site pilot plants were set up. The results of the trials particularly those using chemical aids were encouraging and it was found that chemical aid performance was largely dependent on the degree of mixing at and downstream of the chemical addition point. Design alterations to settling pond configurations in conjunction with optimised chemical addition yielded dramatic results in the form of reduced effluent turbidities. &nbsp; A generalised approach to effluent treatment was developed and some of the specific &apos;mix and match&apos; requirements were identified for different types of sites. The general conclusion is that improved physical treatment combined with good plant management and operation and (where necessary) chemical treatment, will produce water of acceptable discharge quality.

Jan 1, 1989