Search Documents

By Ming’an Wei, Chuanyao Sun, Zhenguo Song, Zengwen Dou, Yangge Zhu

"The effects of pH value and dissolved oxygen(DO) in the pulp to the Eh and flotation recovery of pyrite were investigated using potential online detection system. The effects of DO on the Eh and flotation recovery were tested which DO changed from 0.5mg/L to 19.5mg/L in six different pH buffer flotation systems (pH: 4.00, 5.62, 6.86, 9.18, 10.01 and 10.96 respectively). Results of potential detected online demonstrated that the pyrite electrode has nearly the same response to potential as with platinum electrode for the FeS2-xanthate-H2O flotation system under the study conditions. Pulp potential and recovery of pyrite were remarkably influenced by pH, both of them decreased with the increasing of pH and, especially, sharp decreased after pH above 9. As the concentration of DO was increased, the Eh was also increased in all the six different buffer solution, while the flotation recovery was decreased. And the amplitude of variation for Eh was not obvious in acidic and neutral solutions, but on the contrary, the change for flotation recovery was remarkable in neutral and alkaline conditions. This may indicate that the flotation of pyrite will be deteriorated in alkaline and high DO concentration conditions."

Jan 1, 2014

By J. Stachulak

In recent years more emphasis has been placed on the control of nitrogen dioxide (NO2) emissions from mining diesel equipment. Worldwide, diesel engine regulations to control emission and protect the environment are also driving the development of the diesel engine technology to reduce oxides of nitrogen NOx (Nitric oxide, NO + NO2). NOx are toxic gases produced in mines during the operation of diesel equipment. Most of the diesel equipment used in underground operations are equipped with Diesel Oxidization Catalysts (DOCs) designed to reduce carbon monoxide (CO) and hydrocarbons (HC). The effects of DOCs on NO2 production from diesel powered equipment is not well understood. DOCs do not alter NOx concentration, but may promote the oxidization of engine exhaust NO to the more toxic NO2, thus increasing the undesirable NO2 exposure of workers in the mine environment. In 2012, the ACGIH reduced the NO2 TLV concentration value from 3 ppm to 0.2 ppm. Vale and CanmetMINING have been involved in several research projects to reduce diesel emissions exposure to workers. One aspect of the current program is to determine the effects of in-use DOCs on NO2 production. Several in-use DOCs taken from mining equipment were selected for testing in the laboratory using ISO 8178-C1 and mine LHD transient test cycles. The paper presents the laboratory test results and effects of DOCs on NO2 production. The results indicate significant reductions in CO concentration, by over 77%, while increases in NO2 varied from 46% to 315% based on the ISO 8178-C1 8-mode steady state test cycle. The mine LHD transient test cycle showed the same pattern, although the magnitude of CO reduction was less. Consequently, it is recommended the use of only those DOCs that have been properly evaluated and shown not to significantly increase NO2 emission in the environment be used on mine equipment.

Aug 1, 2013

By S. -H. Sohn, M. -K. Cho, G. -G. Hong

In order to evaluate the properties of coating materials for BOF, the effects of dolomites (dolomite and light burned dolomite) addition on durability of coating materials were investigated. In all coating materials, matrix was dicalcium ferrite(C2F) and both free MgO and dicalcium silicate(C2S) were precipitated. Fe203 content must be controlled to improve the adhesion and durability of coating materials for BOF during oxygen blowing process. The amount of dolomites added to BOF slag must be controlled in optimum condition with high refractoriness of C2S to improve the adhesion of coating materials for BOF. The weight ratio of converter slag to dolomite must be below 8 to improve the adhesion and durability of coating materials simultaneously.

Jan 1, 2004

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By Jacob L. Brinkman, Catherine E. Johnson

Researchers are exploring the use of unmanned aerial vehicles (UAV) to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect density-based concentrations as measured by some governing entities, including the Occupational Safety and Health Administration (OSHA). 

By Jun Lu

The Pittsburgh seam is the most extensively mined coal bed in the Appalachian Basin. Unlike most other prominent coal seams, the Pittsburgh seam typically includes a sequence of immediate roof coals and intervening rock binders (or ?draw slate?), most of which are within mineable horizons. Furthermore, unlike the main bench, the thickness of the overlying roof coals and their intervening rock binders can vary significantly. For instance, in southwestern Pennsylvania, the Pittsburgh seam main bench typically ranges from about 5.0 to 6.0 feet thick with minimal variation over short distances. On the other hand, the Pittsburgh seam roof coals and immediate roof binder typically range from a few inches to several feet, and in certain geologic settings can vary significantly over short distances. Additionally, in some locations, very thick draw slate can totally replace the roof coals. Since the draw slate, which typically consists of claystone or clayladen shale, is relatively weak, the presence of thick and variable draw slate in the roof and rib can significantly affect mine safety and productivity. This paper presents the adverse effect of thick draw slate on a 1500-foot-wide longwall face in a southwestern Pennsylvania coal mine. Mapping of the thick draw slate, numerical models which illustrate stress distribution and failure associated with thick draw slate, and operational adjustments instituted to mitigate the negative impact of thick draw slate will be discussed in detail.

Jan 1, 2013

By Tim Wolf

The author has seen an increased use of shaft-mounted, right angle drive assemblies. These designs use the pulley shaft as its 'foundation" and can create significant overhung loads. To reliably perform, the pulley and shaft must be designed for these special requirements. This paper will focus on the development of overhung loads and their design effects. Special considerations to maximize performance will be presented and comparisons with other drive options will be made. Experience in heavy mining applications will be used throughout.

Jan 1, 2000

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By Jianmin Qin, R. V. Ramani

The major parameters affecting dust flow at a longwall face are dust generation rate, air velocity and quantity distribution at the face, and the characteristics of the dust such as particle size distribution, density etc. Previous studies have identified the longwall shearer as the major source of the airborne dust in the faces. In this study, the effects of dust generation rate and shearer speed on the levels of ambient dust concentration are investigated. A series of experiments were performed under controlled conditions in a full scale simulated longwall face at the Lake Lynn Laboratory mine of U.S. Bureau of Mines using characterized bituminous coal dust. A trickle-duster was moved up and down the longwall face to simulate the shearer. In each experiment, a known amount of dust was dispersed by the trickle-duster into the air and the average dust generation rate was calculated. At the same time, gravimetric respirable and total airborne dust samples were collected and air velocity measurements were made along the face. The experimental conditions, data, and results are presented and discussed in this paper. The airborne dust concentration and air velocity data indicate that the concentration increases and air velocity decreases with distance from headgate for the first half of the face. Towards the tailgate, the air velocity increases with increasing distance but the dust concentration levels off with some variations. The data show that a higher dust generation rate results in higher dust concentration levels. More importantly, the data show that the rate of increase of airborne dust concentration is higher than that of dust generation rate. For the same air velocity distribution and dust generation rate, lower speed of the dust source results in higher airborne dust levels at the face.

Jan 1, 1991

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020

By George F. Comstock

IT has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- [ ] loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferro-alloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. METHOD OF USING DEOXIDIZERS The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel [ ] shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to ¾ -in. lumps,

Jan 1, 1942

By Charles Zdazinsky

Over-break is undesirable in underground civil construction because it excessively damages rock along the perimeter of the tunnel, which directly influences the cycle times of advancement. A quicker cycle time for each process is required to optimize the operation and therefore minimizing over-break is essential for operational success.

Jan 1, 2015

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By M. Oguz Ozkazanc, Gulsev Uyar Aldas

Because of its safety, being easy to handle, relatively inexpensive and containing a lot of energy, ANFO is the most popular and widely used explosive in Turkey as well as other countries in the world. According to change dated May 14th 1999 on the regulation 87/12028 related with explosives, blasters are not allowed to mix ammonium nitrate and fuel oil in the tield to make ANFO. Instead of this, they have been forced to use the ready ANFO prepared by explosive producer firms. As a result of this obligation, the use of technical nitrate for agricultural purpose and mixing AN and fuel oil in unsuitable conditions have been prevented. Indeed, wrong mixture means waste of energy and money.

Jan 1, 2001

By Henara Lillian Costa

This paper aims to investigate the effects of a possible incorporation of ethanol to the lubricant during engine use on friction and lubricant film thickness, by adding small amounts of ethanol to Group I base (with and without an organic friction modifier) and to formulated oils. Film thickness was measured using ultrathin film interferometry. Friction tests were carried out using a mini-traction machine to obtain Stribeck curves. The film thickness measurements showed that in the region of low speeds, where the elastohydrodynamic film is very thin and therefore boundary lubrication may prevail, the addition of ethanol produced some boundary film, which was not present for the base oils. For the base oil with an organic friction modifier, the presence of ethanol increased the thickness of the low friction boundary film. For the formulated oil, the addition of ethanol reduced film thickness in all lubrication regimes. The friction tests showed some friction reduction due to addition of ethanol to the base oil, in particular at low speeds. For the formulated oil, the addition of ethanol reduced friction at high speeds, which was associated to a reduction in the viscosity of the lubricant, but at low speeds, the presence of ethanol reduced the formation of a boundary layer, increasing friction. For the base oil containing an organic friction modifier, the presence of ethanol increased the range of speeds for which low boundary friction occurred.

Jul 31, 2018

By S. Noh, T. K. Kim, B. O. Lee

Future nuclear reactor systems such as a sodium-cooled fast reactor are being designed under severe conditions in terms of operating temperature and irradiation fluence compared to current commercial reactors. For realization of such systems, it is necessary to develop an advanced structural material having both high strength and irradiation resistance at high temperatures. Oxide dispersion strengthened (ODS) steel is considered as one of the most promising structural material because of its excellent creep and irradiation resistance on the basis of uniformly distributed nano-oxide particles with a high density. Up to now, ODS steels have been intensively studied and developed to apply these materials to the in-core structural component of future nuclear systems. Several advanced ODS steels were designed and fabricated by a mechanical alloying, hot isostatic pressing and hot extrusion processes. This study focuses on the effects of heat treatment parameters during the fabrication process parameters on the microstructures of ODS steels for future nuclear system applications.

Jan 1, 2015

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By M. K. Larson, B. G. White

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the causes and mechanisms of roof failure in underground mines. It is expected that a better understanding of these causes and mechanisms will lead to better layout and support designs that will help prevent accidents and fatalities associated with fall of ground. Two numerical experiments were conducted by NIOSH researchers using the Fast Lagrangian Analysis of Continua (FLAC) computer modeling program with a strain-softening continuum to simulate fracture zones. Two models, one of a round hole in a plate and one of a rectangular opening, were constructed and boundary conditions were applied to simulate far-field shear. The Particle Flow Code in Two Dimensions (PFC2D) computer program was used to look at the effects of far-field shear in generating fractures around an underground opening, but these models are preliminary until boundary conditions, strengths, and stiffnesses are matched to the FLAC models. Results showed that shear zones propagated from the opposite corners of openings in directions that appeared to be determined by opening shape and far-field stress. Tensile failures also formed and extended away from these shear zones. The consistent direction of shear deformation with respect to far-field shear provides a plausible explanation for preferred directions of shear as seen in geologic environments.

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024