Search Documents

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011

The Kennedy Siltstone Open Cut provides graded rock for stope filling. Rotary drilling of 310 mm blastholes with a Gardner Denver GD120 is used, and the successful application of an equilateral triangular drilling pattern is described. Charging practices and the development of bulk slurry handling are outlined. Blast monitoring plays an important role in K.S.O.C. drilling and blasting operations. The proximity of nearby residential areas (1300 m) and the Mount Isa Airport (4500 m) necessitates special attention with regard to the minimisation of both air blast and ground vibration levels. The application and control of drilling and blasting parameters has had a direct bear- ing on success of the mining operations and also played an important role in reducing the disturbance to the community.

Jan 1, 1978

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Nelson Severinghaus

THE Rock Chapel plant of Consolidated Quarries Corporation (Fig, 1) is three miles northeast of Lithonia, DeKalb County, Georgia, It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also presents several theories on the action of explosives in this type of blasting. FIG, 1.-PLANT OF CONSOLIDATED QUARRIES CORPORATION, WITH QUARRY AT UPPER LEFT. The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends down-ward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break down the rock in large blocks.

Jan 1, 1938

By Nelson Severinghaus

THIS Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also present, several theories on the action of explosives in this type of blasting. [ ] The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break clown the rock in large blocks.

Jan 1, 1938

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By C. A. Pierce

UNDERGROUND operations of the United States Potash Co. at its mine near Carlsbad, N.M., have been continuous since the property was opened about five years ago. Approximately one million tons of potash has been mined and two shafts have been sunk, each to a depth of about 1000 ft. Outstanding in the company's operations is the fact that not a single blasting accident has occurred during the aforesaid period. The purpose of this paper is to describe the blasting practice that has made possible the achievement of this accident-prevention record. The mining method employed in extracting the thick horizontal bed of potash may be described as a double-entry room-and-pillar system. Mine development is kept well in advance of extraction operations, and a three years' supply of ore, at least, is always available. Limits of the orebody have not been determined, and in the present system of mining headings are advanced by a "shortwall" method. This was the first potash ore bed developed in the United States. The nature of the deposit, therefore, was unknown, and it was deemed expedient to outline a conservative mining policy. Later, when more is known about the deposit and certain control ascertained, a "longwall" panel retreating method may be found advisable. The necessity for a domestic supply of potash became a national issue previous to and during the World War. The United States Govern-ment came to realize that this country should not be dependent upon foreign sources of potash, and began extensive explorations in many parts of the country, seeking an orebody that would meet the exacting require-ments of the domestic market. The Department of Interior, through the Geological Survey and Bureau of Mines, made every effort to determine the location of potash deposits and encouraged their exploitation by private capital. Through the combined efforts of the Department of Interior and private industry, the deposit now being worked by the United States Potash Co. was discovered and brought into production.

Jan 1, 1936

By Thomas P. Mahoney

Phelps Dodge Corporation's Tyrone Mine is a large open pit copper operation located in the southwestern corner of New Mexico. The Tyrone concentrator processes approximately 50,000 tons per day of copper ore. The waste ratio for this operation is 3:1; e.g., for every one ton of ore mined, three tons of waste material are also removed. This results in a mining rate of about 200,000 tons per day.

Jan 1, 1986

By Richard H. Willey

EFFICIENT handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. BINGHAM CANYON MINE The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been metamorphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling and blasting of the porphyry apparently becomes easier as depth is attained, but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. PAST METHODS At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1947

By L. van Hijfte, A. Piché

"Drilling and blasting are fundamental operations in the mining cycle and constitute an important component of the mining costs. Problems associated with improper drilling and blasting practices can create losses of several millions of dollars per year. For this reason, a Blasting Technology program was initiated in 1984 at the Noranda Technology Centre (NTC). In this paper, advances made at NTC in drill and blast technology are reviewed. Impacts of drilling and basting for Noranda are assessed in terms of dilution and ore losses. Future challenges are addressed. IntroductionUp to 1997, Noranda was a diversified natural resources company that operated in three sectors: mining and metallurgy, forest products, and oil and gas. The company employs more than 33 000 people in operations and sales offices around the world. Today, Noranda has returned to its roots in mining and metallurgy. The new vision of Noranda is to be dedicated to the responsible and profitable development of mineral resources around the world for the benefit of its shareholders. In so doing, Noranda will continue to be deeply committed to the environment, health, workplace safety, cost competitiveness and return on capital. Technology is an integral part of Noranda’s success strategies. For this reason, the Noranda Technology Centre, formerly known as Noranda Research Centre, was founded in 1963. Since then, it has undergone four expansion phases to keep up with the increasing needs of the businesses. Today, NTC employs more than 220 specialists who work in partnership with different Noranda companies to identify, develop, and transfer technology to the operations, as well as to explore new sectors of activity."

Jan 1, 2000

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By Darrel W. Hansen

Morrow Point Dam and Power Plant are principal features of the Bureau of Reclamation's Curecanti Unit of the Colorado River Storage Project. They are under construction on the Gunnison River 20 miles east of Montrose, Colo. Johnson-MK is the prime contractor, and represents a joint venture of Al Johnson Construction Co., Minneapolis, Minn., and Morrison-Knudsen Co., Inc., Boise, Idaho. The power plant will be housed in an underground chamber in the left abutment, approximately 250 ft behind the original canyon wall. The chamber is 206 ft long and 57 ft wide. The distance from the foundation to the spring line of the roof arch varies from 51 ft in the service bay to 120 ft in the control bay. The roof arch has a rise of 16 ft. The longitudinal center line of the chamber is orientated east-west with the draft tubes discharging nearly due north. Access to the power plant chamber was possible through the cable tunnel, access tunnel, two draft tube tunnels, two penstock tunnels, exploratory tunnel, which became the ventilation tunnel, or the grouting and drainage tunnel leading to the dam. (See Fig. 1.) The shortest and fastest access was through the cable and access tunnels, and the contractor drove these two tunnels simultaneously. The cable tunnel and cable gallery excavation exposed a transverse section, at the west end of the chamber, that was 15 ft wide and extended from the crown to 5 ft below spring line. It was here that arch excavation began. The first 34 ft of advance along the arch was driven on three headings, and the muck was removed through the cable tunnel. Meanwhile, the access tunnel was completed, and a raise was driven from its crown to intersect the advancing arch excavation near the longitudinal centerline

Jan 1, 1968

By Deepesh Yadav, B. S. Choudhary

Underwater drilling and blasting is conducted for deepening of sea channels for port berths, lake or reservoirs for water supply etc. so that rock dredging becomes easier. During this process there are several associated unwanted effects having potential to cause damage to surrounding structures and the environment, flora and fauna. Though all these ill effects can’t be completely eliminated but adopting controlled blasting techniques can minimize these to tolerable levels. It is recognized that ground vibrations resulting from rock blasting below water near dam may endanger the safety of earthen dams. Therefore, controlled blasting technique was used to ensure the safety of dam and its efficacy was established by monitoring of blast vibrations. The usage of small quantity of explosives confined in blast holes, non-electrical delay detonators and initiating each hole with a separate delay helped to minimize the ground vibration effects on surrounding structures.

Jan 1, 2018

By Barber J

The manganese ore of Groote Eylandt is a shallow sedimentary deposit of Cretaceous age. There are a number of deposits which vary greatly in ore texture, density, percentage of matrix and thickness. The thickness in the present five operating quarries varies from 1-5 metres. The mine output in 1973 was 3 million tonnes of which 60% was blasted, the remainder ripped and bulldozed. The shallow deposit and its varying thickness create rather unique blasting problems which must be overcome in order to produce a minimum overall mining cost but not necessarily resulting in a minimum drilling and blasting cost per tonne. Future planning envisages the introduction of site mixed slurry explosives following test work and the application of a twin boom single operator rotary percussion drill. The paper outlines the overall developments,present and envisaged practices and the reasons for these changes.

Jan 1, 1974

By T Galvin

Drilling and blasting at Westside Mine near Wallsend, NSW, has presented a challenge for Orica Explosives, Australia. The colliery produces 600 000 tonnes of steaming coal per year from two seams using surface mining techniques. Tapping into underlying coal will greatly improve the yield, but there are many issues which make this an enormous challenge. Hunter Valley Earthmoving engaged Orica Explosives to supply the explosives products and to provide much of the blasting expertise that is needed on the minesite. Hunter Valley Earthmoving and Orica Explosives have proven to be an outstanding, unified technical team on this project. The success of the team is based on good communication, progressive attitudes, extensive expertise in blast design and most importantly, care and accuracy in implementing the agreed upon designs.

Jan 1, 1999

By Lemberg D. W, Friday R. G

Potential means of lowering overall costs to permit deeper stripping include : 1. the use of larger diameter blastholes in highly-fissured strata (to reduce drilling costs); 2. dewatering from semi-permanent bores to reduce blasting costs (by maximising the use of bulk ANFO) and promote highwall stability; and 3. the use of inclined blastholes, bulk AN, staggered V1 patterns, adequate backfill and more cost-effective stemming columns. Each of these is covered. The pumping of bulk watergels continuously raises the blasthole water column, thereby perpetuating the demand for these blasting agents. This must be a principal consideration when choosing between a bulk and a packaged watergel. Any packaged product should exhibit dimensional permanence and an energy yield per metre length equal to that of bulk ANFO. Possible ways in which controlled trajectory blasting (CTB) could benefit deeper stripping operations are outlined. By allowing the maximum use of bulk ANFO, de- watering may be a prerequisite of a viable CTB Operation.

Jan 1, 1981

By John Dean Smith

In order to discuss problem solving techniques for the future. we must first review the past. This paper will discuss the drilling and blasting problems and techniques that were used by .Imax Coal in the past few years, tn those of today.

Jan 1, 1991

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996