Search Documents

Controlled-blasting experiments in small development drifts were conducted at CANMET's Experimental Mine in 1992 and 1993. The objective of these experiments was to develop suitable controlled-blasting techniques for small development headings that are drilled by jackleg with 32-mm-diam holes. The experimentation was also aimed at providing insight into blast-damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rock-mass structural data. The drift faces were approximately 2.4 by 2.4 m (7.9 x 7.9 ft) in size with 36 to 43 holes drilled to a depth of 2.4 m (7.9 ft). Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO was used as the main explosive and decoupled 19-mm (0.75 in.) diam semigelatin dynamite charges were used in the perimeter holes. Smooth-blasting techniques and presplitting were tested in the underground mine. All of the blasts were monitored with a multichannel blast-vibration monitor, to which was attached sets of high frequency geophones and accelerometers. These experiments demonstrated the efficiency of controlled-blasting techniques for the reduction of blast damage and also demonstrated the need to improve the safety and efficiency of using explosives.

Jan 1, 1997

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By Barbara A. Sciever, John H. Sr Schue

Riverboat gambling has caused quite a sensation among people since its talk of coming to Illinois. The year 1992 marked the start of an era for people that had a penchant for gambling, it was the year that riverboat gambling was legalized in the State of Illinois.

Jan 1, 1995

By A. F. McKown, P. E. Sperry, W. L. Fourney, D. E. Thompson

INTRODUCTION Underground drill and blast excavation is usually accomplished with small diameter holes loaded with high energy explosives. The detonation pressures are extremely high and an extensive amount of energy is dissipated in the process; however, very little of this energy is used to create the specified fracture planes required for excavation. The available energy is expended in producing radially outgoing stress waves, in crushing the adjacent rock, and in producing a dense, randomly oriented radial crack pattern about the holes. This causes several undesirable effects: 1. Overbreak at the perimeter, which results in more muck to remove and extra concrete or shotcrete to fill the voids. 2. Damage to or loosening of the remaining rock at the perimeter which may result in the need for additional support measures. 3. Ground vibrations and/or airblast, which could result in damage to nearby structures and complaints by people living or working in the area. Several steps may be taken to minimize these effects. Where control of the perimeter is desired, smooth blasting techniques are generally employed in which the spacing and burden of perimeter holes are reduced and lighter, decoupled charges are used. Where vibration damage to structures is feared, control is generally exercised by limiting the charge weight per delay period so that the ground vibrations at the nearest structure do not exceed a peak particle velocity of two inches per second. Where blasting complaints may be a problem, con-

Jan 1, 1979

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

Good blasting practices based on the careful application of explosive energy lead to significantly safer mining operations. Case studies demonstrate how the selection of the correct charge mass, explosive type and round design are vital for extracting the exact amount of rock required and preventing spurious damage to the remaining rock mass. In other cases the explosives are applied to precondition the rock mass, design rockburst resistant support, prevent damage to important excavations and reduce the exposure of miners to unsafe conditions. The Hybrid Stress Blasting Model is used to understand the explosive rock interaction and to illustrate and contrast good and bad blasting practices. In all cases, good supervision is required to continue safe mining according to the design. Keywords Blasting, safety, production, preconditioning, explosives, numerical modelling, drop raising, vibrations, and presplitting.

Jan 1, 2011

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By Abraham Lindo

Panama’s current economical growth demands an increase in electric power supply; projected energy supply for 2012 exceeds the demand by as little as 2%. In an effort to comply with the demand, several different hydroelectric projects, promoted by the government, are currently under construction and each of them vary in generating capacity, construction design and complexity.

Jan 1, 2013

By G Gopinath, R Balachander, H S. Venkatesh

This paper describes in detail the controlled blasting adopted and the measurements undertaken for the successful excavation of large twin tunnels under a shallow cover for a six-lane highway project in India. The tunnels are D-shaped, each 15 m in diameter, and the cover between the tunnels and the existing railway track was about 14 m. These twin tunnel tubes were characterised by two separate three-lane carriageways for each direction of traffic, and were planned with about 25 m of reinforced cement concrete (RCC) portals at the entrance and exit of the tunnels. The major challenge of the project was the blasting of tunnels in rock below an operating railway line. As the tunnels approached the area below the railway line, the ground vibrations were monitored vertically above the blasting faces and on the railway track sleepers. Vibration intensities between those generated from tunnel blasting and those from the movement of the trains were compared, and it was found that the vibrations from blasting were lower than those from the moving trains. Though the permissible level of ground vibration based on the Indian Standard (IS) code happens to be 70 mm/s, the maximum charge per delay was calculated restricting this limit to 50 mm/s. This ensured that the vibrations in the vicinity of the railway tracks never exceeded the prescribed limit of 70 mm/s. The surface ground settlement before and after the blasts were also measured using an optical levelling instrument, which confirmed that there was no significant impact on the surface movements due to blasting. Extensometer readings inside the tunnels showed that there was no deformation in the tunnel. These twin tunnels are now operational and are providing faster connectivity with safety.CITATION:Gopinath, G, Venkatesh, H S and Balachander, R, 2015. Controlled blasting for twin tunnels with a shallow cover under an operating railway line, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The most common method for identifying the potential for blast damage is the peak particle velocity. But this can depend on many factors such as the type of blast, explosive, confinement, timing and the rock mass. The value must then be used to estimate damage. But the amount of damage will depend on the rock mass quality and the excavation size and shape. The amount of damage that can be accepted will depend on the purpose of the excavation. This paper presents a logical, but very approximate, procedure that the mining engineer can follow in order to assess the potential for damage in the control of that blasting.

Jan 1, 1987

By John Yenter

"Unique blasting problems during reconstruction and expansion of 100 year old buildings toaccommodate gambling. Located on steep mountainous terrain and linked by narrowroadways, the towns of Central City and Black Hawk challenged blasters to exceptionalmeasures in order to control over_break, vibration, public exposure and damage to thecharacter of these historic mining towns. Utilities were also upgraded to fit demands of asmuch as 800% volume change in one year."

Jan 1, 1993

By Törbjorn Naarttijärvi, Bengt Ludvig, Agne Rustan

"Falling rock is one of the major causes of serious injuries and deaths in Swedish mines. The research at the Division of Mining and Underground Construction was therefore directed toward controlled blasting in hard intense jointed rock.The project was started with an extensive literature review. Model tests with a new equivalent model material have been initiated to find ways of improving blasting techniques. The result showed that long cracks arise at the perimeter holes when there is a long time delay between adjacent holes. This led to the theoretical development of a new initiation method with ultra short delays (1,5 ms) f or controlled blasting, called ""Cutblasting"".Full-scale tests have been done at LKAB in Malmberget in hard intense jointed magnetite ore. Four different types of perimeter charges have been tested, namely: tube charges, ANFO mixed with plastic beads, detonating cord and linear shaped charges. Three types of initiation of the perimeter holes have been used, conventional (half-second delay detonators), instantaneous and ultra short ""cutblasting initiation"" (1,5 ms delay). The change in rock strength before and after blasting has been studied with bore hole periscope, vibration measurement and ocular observation of the rock surfaces.Thefull-scale tests showed that ""cutblasting"" with detonating cord in the perimeter holes gave the smallest damage to the surrounding rock. A combination of cutblasting initiation and tube charges are anticipated to give an even better result. A new method of controlled blasting using linear-shaped charges has also been tested, however, this charge type needs further development.The full- scale test also showed that the damage which can be seen on the rock surf ace is about the same for different controlled blasting methods but the not-visual-damage zone varies as much as from 0,1 to 0,7 m.A new classification system for controlled blasting regarding the damage to the surrounding rock has been devised."

Jan 1, 1985

By Sérgio Augusto Ferreira, Alan Gerson Diaz Butron, Carlos E. Arroyo, Marcus Neves, Jorhs Enrique Casimiro Huayhua, Dieggo Santos, Eventomar Junior

The presence of natural underground cavities is normally a characteristic of iron ore deposits, specifically in tropical deposits. Brazil and the United States are the only countries that have a legislation to protect these structures, but in Brazil this legislation is very specific for the existing cavities in the federal territory. These cavities are classified by their level of relevance as high, medium, and low. From this perspective, its preservation becomes mandatory, especially, for those of high relevance in order to protect the species (flora and fauna) that live in them. When these structures are within the production phases, it becomes a challenge to exploit these reserves with the use of commercial explosives, since these structures condition and may restrict the use and amount of explosive charge. This paper presents the methodology of controlled blasting associated with predictability via realistic simulation in production polygons, applied in a Brazilian iron ore mine where there is a presence of high relevance natural cavities with restrictions in relation to the limits of Peak Particle Velocity (PPV), which is product of detonation.

Feb 6, 2023

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Gordon F. Revey

In underground construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speedup the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high. In this paper, general methods of conducting blasting risk evaluations and outlined and considerations for blast design and risk management are reviewed. This paper also includes three blasting case histories demonstrating how these techniques were used at recent projects. In the first case, a cautious blasting program was developed to facilitate the removal of concrete and rock within a large section of an active mineshaft. The second case involved critical blasting to excavate a dry lake-tap connection between a tunnel and a shaft at the Southern Nevada Water Intake No. 2 project in Henderson, Nevada. The third case history describes how novel blasting methods were used to carefully drop a 2,721,500-kg (6,000,000-lb) concrete caisson into a1.2-m (4-ft) rock socket at the Detroit Outfall No. 2 project in Detroit, MI.

Jan 1, 2001

By C. W. Baxter

Eveleth Taconite Co. was formed in 1963 to mine and beneficiate taconite on the Mesabi Range. Its Thunderbird mine is located mid-way between the cities of Eveleth and Virginia, Minn. The program for blasting restraints here is unique not only on the Mesabi Range but possibly in the world. The ore is a hard siliceous taconite. Its structure varies from bedded to massive with prominent vertical jointing. The jointing of the top or outcrop of the orebody is a challenge for the blasting practices as it is the source of an estimated 75% of the secondary breakage.

Jan 11, 1972

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997