Search Documents

By Luís Marcelo Marques Tavares, Gilvandro Bueno, Túlio MoreiraCampos

The HPGR development and application in the minerals industry resulted in an important increase in its application in iron ore pellet feed processing in the last decades. Vale SA was one of the pioneers in application of the HPGR in integrated plants, currently operating with six HPGRs in the pelletizing plants of Complexo de Tubarão (Vitória, ES). The work uses the mathematical model of the HPGR, proposed by Torres & Casali and modified by the present authors, to predict the performance of two industrial pellet feed HPGR units of the Complexo de Tubarão. Besides model validation, results of process simulations are shown in order to optimize the pellet feed pressing according to industrial demands, presenting different scenarios that are more attractive to HPGR operation. Simulations showed that it is feasible to reduce the specific surface area of the HPGR feed from 1770 cm²/g to 1570 cm²/g, allowing to produce a pellet feed of the same quality in its product (1911 cm²/g) and therefore reduce the work done by upstream ball milling.

Oct 1, 2019

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By J. R. Hassemer, T. T. Chao, University of Georgia, K. C. Watts, R. F. Sanzolone

Secondary oxides of Fe-Mn have been used in mineral exploration from the time gossans were first recognized Since gossans are conspicuous features and are largely explored, it is necessary to look for more subtle indication of blind mineralization. Sampling materials used in these geochemical studies consist of secondary Fe-Mn oxide-rich products of hydrothermal mineralization, and "in situ" weathering found in fracture fillings-as selvages along joints and disseminations in host rock. These materials were selectively collected and studied in the Silver City mining region. Two independent sampling methods were compared. The difference in the sampling methods was mainly in the ways samples were obtained and processed. One method involved systematic sampling of fracture fillings and coatings from which secondary Fe and Mn oxides and associated trace elements were then selectively extracted by chemical methods. The second approach involved collection of composite stream sediments and physical extraction of Fe-Mn oxide materials by gold panning, bromoform concentration, and electromagnetic separation. The source of the Fe-Mn-rich materials in the stream sediments is considered to be fracture fillings and coatings that mechanically entered the drainage basins. Map distributions of the two-sample types were compared. Both methods showed generally supportive patterns of anomalous metal dispersion, although anomaly-to-background contrast seems better in joint coatings. Both were useful in distinguishing geochemical differences between mining districts in the region. For example, the Pinos Altos district may contain more hydrothermally-introduced iron than the Central district, whereas the Central district has lead and zinc enrichments that are less on the amount of iron enrichment than is the case in the Pinos Altos district. The methods were qualitatively compared relative to time, expense, and other advantages and disadvantages.

Jan 1, 1984

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Ahmed Mohamed Elmahdy, Hidekazu Matsuoka, Kyushu University, Tsuyoshi Hirajima

"Selective flotation of chalcopyrite and molybdenite was studied using various surface treatment methods such as electrolysis, ozone treatment, and plasma. Oxidation via electrolysis method indicated that only chalcopyrite surface is affected by electrolysis due to conductivity difference with molybdenite. Oxidation treatments and XPS analyses indicated that chalcopyrite became hydrophilic due to deposition of oxidized iron on its surface. Various oxidizing methods also showed that chalcopyrite was selectively oxidized and this can apply selective flotation of chalcopyrite and molybdenite. The possible mechanisms are proposed in this work based on surface analyses and thermodynamic calculations.INTRODUCTIONCopper sulphide minerals often associate molybdenite (MoS2) which is one of the most important by-products (Wills, 2006). It is important to recover molybdenite perfectly not only since molybdenite is valuable mineral, but also contamination of molybdenite into copper concentrate or contamination of copper mineral into molybdenite concentrate indicates penalty for both concentrate values (Wills, 2006). Conventional separation of copper sulphide and molybdenite has been achieved with sulphide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulphide. However, this current process shows imperfect molybdenite recovery and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant. Hirajima et al., (2014) have been studied selective flotation of molybdenite and chalcopyrite (CuFeS2), which is the most important copper mineral, with plasma pre-treatment. They reported that plasma pre-treatment process followed by washing treatment can improve molybdenite floatability and depress chalcopyrite. This result is attributed to surface oxidation and selective conversion of chalcopyrite and molybdenite wettability. It may be hypothesized that another surface oxidation methods could give a similar result as plasma treatment process. To test this hypothesis, in this study, as comprehensive study of oxidation effect, various oxidation methods such as electrolysis, ozone, and plasma were investigated. Electrochemical measurements, thermodynamic calculations to predict the chemical reactions happened during the process, various surface analyses, and flotation experiments were carried out."

Jan 1, 2016

By J Rayo

Andean countries (Chile, Peru, Bolivia and Argentina) have 42 semi-autogenous mills (SAG) in operation and there are more than 30 projects in the pipeline that consider SAG mills. At the end of the next decade, the total amount of SAG mills in this area will likely be close to 100.There is a lot of reliable operational information collected by JRI Ingenieria Sociedad Anonima, the author’s engineering company, for more than 20 years and processed by statistical software, to be used as a reference for design basis of future projects or to improve operations by comparison. JRI Ingenieria Sociedad Anonima has reliable information related to the performance of more than 50 per cent of the Andean SAG plants.The paper presented considers a set of graphs that summarise the collected and verified SAG plants technical data. The figures will show key parameters as circuits and equipment data, energy consumption, technical availability, utilisation rates, throughput variability, pebble productions, steel consumption and others.The data is compared with typical design basis of several engineering companies and the main differences are analysed and/or commented on.CITATION:Rayo, J, 2014. Comparison of semi-autogenous mills operations in Andean countries, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 283–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E. F. Nelson

The 1970s have witnessed the completion and successful start-up of several new non-ferrous metallurgical operations in the Western Hemisphere which utilize large semi-autogenous mills in the grinding circuits. These facilities' are arranged either as single-stage circuits, or in a two-stage configuration n with ball mills. Another major concentrator, designed with an autogenous mill, ball mill, crusher (ABC circuit), is presently under construction and scheduled for start-up late this year. The large primary mills employed in these circuits have high diameter-to-length ratios and are designed to accept a very coarse feed, i.e., the product of a primary gyratory crusher, or run-of-mine ore. This characteristic obviates the need for a secondary-tertiary crushing plant or, in selected cases, even a primary crusher, which is a basic requirement in feed preparation for conventional grinding mills. This paper discusses three such grinding circuits and, presents operating data for two of them: the Island Copper Mine of Utah Mines, Ltd., near Port Hardy, British-Columbia,- and the Pueblo Viejo Cyanide Leach Plant of Rosario' Dominicana, S.A. on the island of Hispaniola. The design criteria for the Cyprus Bagdad Concentrator under construction' at Bagdad, Arizona, are also included. Data pertinent to these circuits are tabulated in the Summary.

Jan 1, 1977

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By Gary Walters, Matthew White, Thomas W. Gonzales

The copper smelting industry has transitioned into the 21st century compliant with environmental regulations, new smelter installations and brown field expansions. The industry faces new challenges as copper in concentrate grades have decreased while contained impurities have increased. A new benchmarking survey was undertaken to update the last survey of 2016 for operating copper smelters in the world. The information collected was separated based on primary smelting technology rather than by geographical location and supplemented from published literature. Each smelting technology’s unique use of specialized process equipment, concentrate smelting capacity, and impurity flexibility are discussed INTRODUCTION The 20th century was a remarkable time for the growth of copper smelting. Electric, blast and reverberator furnaces dominated the smelting technology well past WWII. In the 1970s, SO2 regulations and high energy cost drove the development of new primary smelting technology. Technological advancements decreased energy consumption and enriched sulfur dioxide concentrations of the process off-gas to levels where sulfur capture in sulfuric acid plants was economically viable. The new smelting technologies began to replace reverberatory and electric furnaces starting in the late 1940s. A new paradigm in copper smelting was established and the enabler was then Outkumpu’s® flash smelting technology from the 1940s through to today. Now, Outotec had become the dominant primary smelting technology with over 44 copper flash smelting furnace installations world-wide. Figure 1 shows the historical installation statistics of primary smelting technologies over the last 70 years (ICSG 2018). The dominance and acceptance of the Outotec® smelting technology from the 1940s to current can be seen. Isasmelt® technology for copper was introduced in the 1970s and did not see advancement in new installations until the 1990s through today. Isasmelt® has 12 world-wide copper furnace installations to date. Mitsubishi® also introduced continuous smelting and converting technology in the 1970s, but had no new installations until the 1990s with a total of 5 copper smelters. Outotec Ausmelt® smelting technology had 3 installations in the 1990s and totals 10 furnaces. Most recently the Chinese technology of Bottom Blown and Submerged Lance Smelting began commercial operations in 2005 for total installations of 11, mostly in China. Other technologies, such as, El Teniente, Noranda, Inco, and Vanyukov furnaces have contributed to the overall global smelting capacity, but have not penetrated the smelting industry to challenge the existing dominant smelting technologies. The technology distribution in Figure 1 also shows flash smelting technology for sulfide concentrate domination untill 2000, bottom blow technology has become the preference in China. Currently, China is the only country building new smelting capacity. Isasmelt® technology also seen a large increase in installations in the current decade.

Jan 1, 2019

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By E. Minnaar, P. J. Cilliers, M. Bellino, L. M. Roux, R. Dye

The classic technique to remove impurities in a cobalt stream is selective precipitation. This is usually followed by re-leaching to produce an advanced electrolyte for cobalt electrowinning. Although this technique ensures an adequate cobalt concentration in the electrowinning circuit, some of the consequences include unwanted losses through the numerous selective precipitation steps resulting in lower recoveries. One plant that currently utilizes selective precipitation is the Luilu Metallurgical Plant (Luilu) in the Democratic Republic of the Congo. This paper evaluates the benefits of using solvent extraction technology as a purification step in the Luilu Process with the aim of further increasing the overall cobalt recovery and to ensure that a suitable cobalt concentration in the advanced electrolyte is achieved. The implementation of a solvent extraction-electrowinning process is found to be beneficial in terms of achieving improved recoveries and cobalt cathode quality, however there are many other factors that impact the success of converting from the classic precipitation process used at Luilu.

Jan 1, 2007

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By George B. Clark, Edward E. Hornsey

Pulses from large underground explosions which traverse the rock beyond the "fracture" and "plastic" zones do not behave as a spherical elastic model. Observed attenuation is greater than that predicted by the elastic wave equation, and the pulse form changes in a different manner, i.e., it usually lengthens with the first power of the distance. To more clearly define a mathematical real earth-wave model, detailed analyses of the spherical elastic and the Voigt viscoelastic models have been made, and results compared with observed wave forms from large confined chemical and nuclear explosions. TRANSIENT SPHERICAL ELASTIC WAVES Scope of Investigation Transient elastic spherical waves were investigated in detail. However, an elastic model is not, in general, an exact representation of wave propagation in rock. An understanding of transient elastic waves is desirable for gaining insight into explosive-generated wave phenomena because it can be employed for comparison of more complex and realistic models, such as the Voigt model, or others which may simulate real earth waves. The study was concentrated primarily on the peak values of the radial wave parameters : displacement, particle velocity, acceleration, stress, and strain.

Jan 1, 1972

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991