Search Documents

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By Gregory A. Knapp

Treatment of industrial wastewaters generally advances with specific chemical concentration and mass-flow targets, established by National Pollutant Discharge Elimination System (NPDES) permits. Treated discharges must also address toxicity to test and receiving water organisms. Various parameters might need consideration during treatment design and planning, such as the known toxicants, hardness, alkalinity, solids, nutrients, metals in both the dissolved and particulate state, and even flow. Since toxicity is used as a "catch all" regulatory monitoring tool, design of treatment systems should focus on the various factors contributing to toxicity.

Jan 1, 1996

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011

By Levente Becze

The zinc bottom dross is obtained as a by-product from hot dip galvanizing operations and contains at least 92 % zinc, which is recycled mainly by pyrometallurgical processes. The overall costs of such a treatment, however, are often relatively high, and the very strict environmental protection regulations might also cause additional difficulties for the high temperature procedures in the future. Therefore, a novel hydro-electrometallurgical process has been developed in our laboratory, by which one can reclaim zinc of high purity, while attempting to achieve low energy consumption and making allowances for all the environmental restrictions. This aqueous processing technique, based on electrolytic refining in a cell equipped with anion-exchange membrane to separate the anode and cathode compartments, allows the indirect purification of the anolyte. Zinc is dissolved from the anode along with some of the impurity elements, while the intermetallic compounds (Fe-Zn, Fe-AI- Zn) are accumulated in the anode slime.

Jan 1, 2003

By Filippos Patsiogiannis

Laboratory size (5 kg) aluminum killed low carbon steel melts were desulfurized with synthetic fluxes in zirconia crucibles. The sulfur, oxygen, aluminum, silicon, and manganese contents in the melt were determined as a function of refining time and temperature. With a good argon shield and synthetic flux cover, melt reoxidation was not observed. Sulfur removal followed first order reaction kinetics. The effectiveness of calcia saturated calcium-aluminate (12CaO.7Al2O3) based fluxes in desulfurizing the steel melts was evaluated. The effects of initial sulfur level of the melt, weight of the flux (slag), and additions of tellurium, fluorspar, and barium oxide to the melt on the kinetics of desulfurization were also studied.

Jan 1, 1993

By A. M. Strachan

Capper Pass & Son Limited Was, until its recent closure, the world&apos;s largest producer of tin from secondary materials including solder drosses, non-ferrous smelter flue dusts, tin based metal alloys, residues and slags. Polonium-210, an alpha emitting radionuclide, was present in varying concentrations in some of the numerous feed materials processed by the smelter and refiner. The polonium-210 followed a complex path through the process flowsheet. This paper discusses the behaviour of polonium, both from its arisings in other smelters&apos; process streams and through the entire Capper Pass smelting and refining circuit. The consequential personnel safety and environmental precautions necessarily taken in some areas of the process operation are outlined.

Jan 1, 1992

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite/Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By Florian Kongoli

The behavior of cobalt as a by-product in the NilCu smelting and converting processes effects directly the quality of the final products as well as the revenues gained from the overall process. An effective way to evaluate and predict this important behavior is thermodynamic modeling which reduces the time and the cost of experimental investigation. In this work a thermodynamic model of cobalt-containing matte phase in NilCu smelting and converting processes is presented. The model predicts a priori the thermodynamic properties and phase relations of the ternary and multicomponent matte based solely upon the optimized parameters of the binary systems. This model can be used with other models such as those of slag, metal, gas etc. to predict various aspects of cobalt behavior such as matte- slag, metal-slag distribution, etc.

Jan 1, 1999

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By Volovik A. V. Ivtan, Shelkov E. M. Ivtah

"One of the most power consumption Industrial process is production of Al from bauxites (about 45000KWt.hour electrical energy for production of 1 ton. of technical Al). This process is based at the low efficiency and productivity electrolysis technology.Last years IVTAN investigations give to .us information about possibility to use of high temperature shaft- furnaces for efficiency production of alumina (AL2O3 ) technical. aluminium and some all.oys on the base of the high temperature carbon- thermal reduction process. At this case power consumption for production of unit of last, product will be less at the 3-4 times.The carbon-thermal method is allow produce alumina (Al203 ), technical Al and its alloys not only from deficient bauxites, but practically inexhaustible reserve of other types of Al-contain row materials (cianite, sillimonite and so on/The thermal-chemical economical analises of fulfilled at the IVTAN, production of alumina. Base on facts of production and technical technology are especially for ones arguments at the high temperature shaft-furnace technical Al and its alloysIn the last decades of the 20-th century, the discharge into atmosphere of high temperature and. combustion gases places . problems before humanity more and more sharply and becomes of great importance task.But at the same time, as production of material values increases, intensity of pollution of environment increases all time. And the value of new processes and. technologies of material production, aimed at reducing the expenditure of power and pollution of· the environment, also increases."

Jan 1, 2000

By Manjie Li, Mingrui Yang, Haijun Peng, Shuxing Qiu, Wei Liu, Shengfu Zhang

It is important to produce and utilize highly reactive coke in order to reduce the energy consumption and CO2 emissions through improving shaft efficiency in blast furnace. The present study aimed to investigate the transformation of iron minerals and properties of iron coke (the coke mixed iron ore fines). Along with the increase of iron ore fines, cold strength displayed a slight downtrend and the pore structure wasn’t inferred to be a major factor affected the properties of iron coke. During carbonization, the majority of mixed iron oxides were reduced to metallic iron by CO and H2 and the degree of metallization achieved to approximately 75%. Nevertheless, produced metallic iron was oxidized by pure CO2 during gasification. Iron coke reactivity index (ICRI) was obviously enhanced and the iron coke strength after reaction (ICSR) drastically decreases, which were also significantly influenced by crystal structure of carbon.

Jan 1, 2015

By L. A. Mills

After three years of experience in operating the pilot plant for the Noranda Continuous Smelting Process, the decision was made, in March 1971, to build an 800 ton per day commercial plant at Noranda, Quebec. The de- sign and layout of the plant is discussed and the installed equipment described. Experience previously gained in the pilot plant is mentioned when it has been used in the choice of equipment or plant layout. The full- scale reactor was started up in March 1973 and the operational datacollected and the experience acquired during the first 30 months of operation are described. This includes operation to produce both high grade matte and copper. Areas discussed include refractory wear, fuel consumption and throughput of copper concentrates. Changes made to original equipment and methods of operation are discussed, together with the reasons. The ad- vantages of using solid fuels to handle inert materials and to maximize converting air flowrates and concentrate throughputs are described. Relative efficiencies of oil and natural gas are compared. The addition of oxygen from a 94 ton per day oxygen plant to the reactor converting air was started in August 1975 and the initial operating results are included.

Jan 1, 1976

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By Marcelo B. Mourao

Interactions of carbonaceous materials with liquid Fe-C melts have been investigated experimentally by determining the volatile yield due to rapid devolatilization (Flash Pyrolysis) and rates of dissolution at temperatures ranging from 1623 to 1873 K. The volatile yield increased with increasing the temperature. The comparison of results of different types of carbonaceous materials was possible by expressing the volatile yield in terms of Enhancement Factor, fE. The rates of dissolution of spectroscopic graphite and an industrial coke seemed to obey the correlation for natural convection under turbulent conditions. The experimental data for the graphite suggested that the rate of dissolution was controlled by the mass-transfer in the liquid boundary layer adjacent to the solid sample. The value for the empirical parameter correlating the dissolution coefficient and the operating variables was found to be 0.19 which was close to that reported in the literature. The comparison of the results obtained for the coke samples with those for the graphite revealed that the impurities and the porosity of the samples can effect the dissolution rates.

Jan 1, 1992

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By Joseph Goodwill

1. PURPOSE The objective of this paper is to summarize a study undertaken by the EPRI Center for Metals Production (CMP). The overall purpose of the study was to identify electrolytic opportunities that might merit consideration for joint development by industry and EPRI. 2. SCOPE The electrolytic technologies of interest to this study include: Electrorefining, Electrowinning, and Fused-salt electrolysis. Recovery from primary, secondary, and waste materials were included in this effort; however, we excluded from consideration: Plating and coating operations, such as electrogalvanizing; Mining and milling operations in which electric energy is predominantly used for comminution; Electrothermal processes in which submerged-arc, open electric-arc, and plasma-based smelting processes use electric energy largely to provide a melting or refining ("heating") capability; and Aluminum electrotechnologies since these were the subject of a separate study (CMP 86-2). We recognize that there may be some "gray areas" between these excluded areas and the electrolytic sectors of interest. For this reason, a secondary criterium was used, namely, if the major use of electric energy was to extract or refine the

Jan 1, 1990