Search Documents

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

Iron(II), sulphur dioxide and sugars such as lactose are potential reducing agents for manganese dioxide to produce manganese(II) for subsequent hydrometallurgical treatment. The leaching of limonitic laterite and manganiferrous ores with sulphur dioxide produces iron(II) which in turn can catalyse the leaching of manganese dioxide in acid media. This paper presents a critical analysis of the kinetics of reductive dissolution of synthetic manganese dioxide and manganese ore to compare and contrast the effect of sulphur dioxide and iron(II) in acid media containing sulphate or perchlorate anions. Both one-electron and two-electron mechanisms are considered in the case of sulphur dioxide. The current knowledge on chemical speciation is used to construct an Eh-pH diagram to show the effect of complexation of Mn(II), Fe(II) and Fe(III) with sulphate. Heterogeneous and electrochemical reaction kinetic models are combined to propose reaction mechanisms which rationalize the dissolution kinetics.

Jan 1, 2003

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By Eltefat Ahmadi

Iron-free titanium oxycarbonitride (TiOxCyNz) is a promising feedstock for production of titanium tetrachloride (TiCl4) at low temperatures. In this study, the effects of leaching variables such as temperature, time, particle size of staring material and concentration of the leaching solutions were evaluated on iron removal from nitrided Malaysian ilmenite by Becher process. The nitrided ilmenite was prepared by isothermal reduction with graphite at 1200 °C for 3 h in H2-N2 atmosphere. The aerated leaching experiments were conducted at 50–90 °C with addition of 0.3–2.0 wt% of NH4Cl catalyst. The highest extent of iron removal (XFe) was obtained at about 96.2% for the sample leached at 90 °C for 7 h with 2.0 wt% NH4Cl. The iron concentrate and titanium oxycarbonitride product were characterized by ICP-OES, XRD, XRF and SEM-EDX analyses. The results indicated that the aeration leaching process was a successful route to prepare low-iron titanium oxycarbonitride.

By A. A. Bustos

Four Air Liquide Shrouded Injectors (ALSI ) were installed and operated for over one year in a Peirce-Smith converter at the Falconbridge nickel smelter in Falconbridge, Ontario, Canada. A shrouded injector consists of an inner pipe and an annulus, through which high oxygen enriched air and nitrogen flow, respectively The nitrogen cools the injector and protects the refractory in the vicinity of the injector tip, allowing for substantial increases in oxygen flow rates to the converting reactions. Several injector designs were tested to study the effect of changes in the cross-sectional area and changes in the entrance geometry of the annulus. An optimum design would minimize the injection pressure required for a given flow rate to achieve choked flow conditions at the tip of the injector. The operation of the ALSI was simple and did not require any special care or maintenance, either between blows or between converter cycles. In particular, the shrouded injectors did not require punching, as is the case with conventional tuyeres. In terms of refractory performance, the ALSI, operating at 30-40 % oxygen enrichment, were superior or equal to the conventional tuyeres, which operated at 21-23% oxygen. The results of the demonstration program led Falconbridge Limited to implement the ALSI technology on a commercial scale The paper presents the demonstration program results in terms of gas flow rates, accretion formation, punchless operation and refractory wear.

Jan 1, 1999

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001

By Jian Pan, Zhen He, Deqing Zhu, Shouyan Yue

"The differences of raw material characteristic among six kind of iron concentrates and the influences on ballability were studied from the aspect of the size distribution, specific surface area and particles morphology. The results show that the specific surface area of iron concentrates has crucial influence on ballability, and the effective method of improving ballability for weak ballability iron concentrate has been found. It is of important guidance for Chinese steel mills to import and use iron concentrate from the whole world.IntroductionChina's steel industry has developed rapidly in recent years, crude steel production in 2011 is an unprecedented 683 million tons, which is almost half of the world crude steel production, and it is equivalent to the total sum production of the nations which rank at 2,3,4,5 and 6 in the world [1]. In order to match the development of steel industry, the blast furnaces are becoming larger and more modernization, therefore charging burden of higher quality is requested, and the reasonable blast furnace burden structure is more and more important, at the same time, for iron ore powder sintering process's continuous improvement and development, another method providing ""concentrate"" for blast fumace-pelletizing is also taken seriously. The grate-kiln method of pelletizing has achieved great development for its unique advantage, and in just a few years, there are over 60 rotary kiln production lines have built or being built in China, the sum of pellets has reached to more than 140 million [2, 3]. The rapidly growth of pelletizing yield demands diverse source of pellet, which include not only domestic magnetite concentrate, but also imported hematite which is high in iron and low in silicon. Usually the ratio of imported hematite concentrate increased gradually. The imported hematite concentrate has high grade and fine particle size (the content of -0.074 mm mostly higher than 90%), but the ballability of part of the concentrates is poor."

Jan 1, 2013

By M. A. Llavona

In Spain, as in many countries, the gold content of jewellery must be officially hallmarked. The official methods of assay are gravimetnc cupellation (a method which is highly accurate but both time and sample consuming), potentiometry, gravimetry and volumetry. In this paper, a procedure for measuring gold by flame atomic absorption in jewellery samples is described. The method is based on the acid digestion of a 40 mg sample. The quantity of aqua regia necessary for dissolving the gold, the ideal weight of a sample in order that the error may be minimal, the effect of the acids employed, the type of material used for its storage, and the necessity of employing a buffer to avoid the ionization of the solution are described. The method proposed is simple, highly accurate and causes little damage to the jewellery.

Jan 1, 1999

By Larry M. Southwick

Pneumatic converting (Bessemerizing) of iron revolutionized the steel industry. Bessemerizing of copper (conversion of copper sulfide matte to copper metal) was proposed at almost the same time, but it was slow in being accepted. The differences between iron and copper converting were great and technical problems were substantial. It took 25 years for the process to become viable and another 25 years before a truly economical solution was found. A major economical and productivity problem was the short life for converter refractory linings. The first converters had acid (silica) linings, which were quickly consumed since silica was a flux for the process. Converters had to be relined at least once per day, a laboriously expensive manual process with only the most rudimentary mechanical aids available to assist. The industry was revolutionized almost overnight when finally a viable basic (magnesite) lining was developed. This lasted 100's of days versus less than one, leading to converters that were easier to operate and which handled larger charges. This change occurred after W.H. Peirce and E.A.C. Smith, with support from the Guggenheim interests, successfully operated a basic lined converter in a copper refinery in Baltimore. While Peirce and Smith are generally given credit for the development and explosive acceptance of this idea, a Pittsburgh industrialist, Ralph M. Baggaley, working in an independent smelter in Butte, Montana, successfully built and operated a basic lined converter four years before they did. In fact, the early support for Peirce and Smith likely occurred because Guggenheim's staff were encouraged after thoroughly examining Baggaley on his earlier successes. The questions of technology primacy between Baggaley and Peirce/Smith are ironically similar to those between Wm. Kelly and Bessemer in converting iron to steel. This paper will review what Baggaley (and other early researchers) accomplished, examine why he (or they) did not receive credit equal to Peirce and Smith and explore what his (their) place should be in the development of successful basic linings. More suspects than a Victorian Whodunit.

Jan 1, 1999

By Ozgul Dere Ozdemir, Muge Sari Yilmaz, Sabriye Piskin, Deren Sibel Kasap

"Galvanic sludge is generated at the end of the waste water treatment process of metal plating system. The waste sludge is one of the main hazardous solid wastes produced by metallurgical industries. It is caused the harm of human health and damage of the environment due to containing reasonable amounts of toxic metals (e.g., nickel, zinc, copper, chromium, iron, lead, cadmium, etc). The concentration of those toxic metals in the wastewater might reach 30% (w/w, dry weight) making their removal and recovery an interesting issue.In this study, synthesized titanium dioxide is used as adsorbent to remove nickel in leachate of galvanic sludge. The adsorption experiments were carried out isothermally at four different temperatures. The effects of pH, temperature, and contact time on nickel adsorption efficiency were investigated, and the optimum parameters were determined from the experimental studies. The experimental results indicated that pH, temperature, and contact time played a significant role on the adsorption capacity of nickel.IntroductionRapid industrialization has caused increasing the heavy metal concentration in biosphere with the industrial wastes. These wastes are generated in various industrial processes such as electroplating. Galvanic sludge is a hazardous waste that generates from metal plating industry by chemical precipitation of heavy metals from acidic or alkaline solutions during the waste water treatment process. Heavy metals are tend to bioaccumulate thus they are treated the living organism [1-2].Galvanic sludge is mainly disposed on landfills for these reason it is a big problem for environment. Galvanic sludge containing nickel (II) is common because nickel (II) is used in electroplating process [3]. In drinking water, nickel may cause health problems if found in amounts greater than the health standard set (MCLG: 0.1 mg/L) by the United States Environmental Protection Agency (EPA). The higher concentration of nickel (II) in ingested water may cause severe damage to lungs, kidneys, gastrointestinal distress, e.g., nausea, vomiting, diarrhea, pulmonary fibrosis, renal edema, and skin dermatitis [ 4]. For these reasons, it must be treated before disposed to landfill."

Jan 1, 2011

By J. D. Sunderkötter, M. F. Stroosnijder, V. A. C. Haanappel

"TiAI-based intermetallic compounds have attracted considerable interest as structural materials for high-temperature applications due to their low density and substantial mechanical strength at high temperatures. However, one major drawback hindering industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 °C. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium, and of the effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of such materials.Extended AbstractIntroductionTiAI-based intermetallics are being considered as construction materials for high temperature components, e.g. in aircraft and car engines, due to their low density and substantial mechanical strength at high temperatures, see e.g. [1,2]. The best ductility can be attained with alloys consisting of y-TiAI with around 5-15 vol.% Q2-Ti3AI. However, one major hindrance to industrial application arises from the insufficient oxidation resistance at temperatures beyond 700 aG. In spite of their high aluminium content, TiAI-based intermetallics do not generally form long-lasting protective alumina scales. After longer exposure times the scales, which are initially rich in alumina, deteriorate and scales consisting of mixed alumina and titania predominate, with high growth rates similar to pure titania.It is not the intention of the present paper to present a general overview of the high temperature oxidation behaviour of TiAI based intermetallics, for which the reader is referred to the literature [3,4]. In the present contribution some general aspects of high temperature oxidation of TiAI-based intermetallics will be presented. This will be followed by a discussion of the influence of alloying elements, in particular niobium. The effect of nitrogen in the oxidizing environment on the high temperature oxidation behaviour of these intermetallics will also be considered."

Jan 1, 1996

By Selvin Yesilay, Guray Kaya, Bekir Karasu, Asli Cakir

"In this investigation, the wastes of Eti Maden Kirka Boron Company of Turkiye were evaluated in the production of diopside and anorthite-based glass-ceramic glazes suitable for porcelain tiles fast and single-fired under industrial conditions. First of all, high wear resistant frits were produced with the use of concentrator and derivative borax wastes. Second of all, pre-engobed porcelain tile bodies were coated with the standard and newly produced frit-based glazes and industrial fast single-firing was employed. Final products were undergone to the certain standard tests to determine their Vickers hardness, wear resistance, thermal expansion coefficient values, gloss and coloring parameters. The micro-structures and phase formations of the fired glazes were also studied. Consequently, it was confirmed that the utilization of borax solid wastes in fast single-fired porcelain tile glass-ceramic glazes is possible. Introduction Porcelain tiles were introduced at the end of 1980s by Friandre, one of the leading Italian porcelain manufacturers. The American National Standard Specifications for Ceramic Tile defines porcelain tiles as: dense, smooth, impervious (with water absorption value less than 0.5 %) and stain resistant [1]. The excellent technical performances for ceramic tiles, such as mechanical, wear, frost and chemical resistance that make their use possible in indoor and outdoor building applications [2-3]. In the last decade, the growth rate of the global production of porcelain tiles increased more than those of other ceramic products; in fact, the technical properties of porcelain tile, coupled with even more improved aesthetic appearance, gave it a prominent role on the tile market [2]. Glass-ceramics are composed materials of one or more crystalline phases immersed in a residual glassy phase [4-5]. Glass-ceramic technology is based on controlled nucleation and crystallization of bulk glass [6]. The concepts of controlled crystallization of glass designate the separation of a crystalline phase from the parent glass in the form of tiny crystals. Their growth rate and final size are controlled by a suitable heat treatment [7]."

Jan 1, 2008

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported' Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003

By M. I. Novgorodova

Most of the gold in the earth's crust occurs as finely-dispersed gold and accounts for much of the gold lost in extraction processes and during exploration for gold. The Compositions, sizes, and morphology of fine gold particles (0.01 to 10 ~m in diameter) were studied with high resolution electron microscopy coupled with electron microprobe and microdiffraction devices, using colloidal carbon replicas. Correlations were made between fine gold, mineral associations and ore genesis. The results provide qualitative information on the proportions of finely dispersed, invisible and visible gold distribution in ores. Such knowledge is fundamental when planning an optimum technological recovery process.

Jan 1, 1991

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By Ronald L. Bruening

IBC Advanced Technologies, Inc. (IBC) has developed and commercialized SuperLig® materials based on Molecular Recognition Technology (MRT), which have proven to be very effective for the removal of bismuth from hydrometallurgical sulfuric acid process streams. The most common application is its removal from copper refinery electrolytes, where bismuth control is extremely critical. IBC has also developed an MRT system for extraction, recovery and refining of palladium from a copper refinery by-product stream originating from the treatment of copper tankhouse slimes. A high purity palladium salt is produced which meets market specifications. Results are reviewed and discussed.

Jan 1, 2003

By Himaki Nakano, Kenji Hara, Toshiaki Tsuru, Shunsuke Kawano, Takeshi Ohgai, Hisaaki Fukushima, Shigeo Kobayashi, Tetsuya Akiyama

"Electrodeposition of Fe-Ni and Zn-Ni alloys from aqueous solutions is one of the well-known examples of anomalous codeposition in which less noble metal deposits preferentially. In this paper, the electrodeposition behavior of these alloy systems was compared between the methanol and aqueous baths. In Fe-Ni system, the significant suppression of the deposition rate of more noble Ni was observed over a wide range of electrolysis conditions in both methanol and aqueous baths. However, the electrodeposition of Zn-Ni alloys showed the typical feature of normal type codeposition in the methanol baths, which was completely different from that in aqueous sulfate baths. The difference in the electrodeposition mechanism between Fe-Ni and Zn-Ni alloys was discussed on the basis of the alloy deposition behavior in the baths in which the activity of water was varied:INTRODUCTION'It has been well known that Fe-Ni alloys show an excellent soft magnetic property. Therefore, thin films of this alloy have been used to fabricate the'-various magnetic devices. For the production of Fe-Ni thin films, dry processes such as sputtering, PVD and CVD are 'employed frequently and the resulting films showed a preferable property as a magnetic material. Electrolyses as a production technique of thin films, on the other hand, has the advantage over other processes in its cheaper production cost due to the simplicity of the production unit The Zn-iron-group metal alloys such as Zn-Ni and Zn-Fe electrodeposited on a steel sheet ale known to exhibit excellent corrosion resistance and therefore the electrodeposition of these, alloys has been applied to the production of surface treated steel sheets mainly for automotive body panels.According to Brenner (1), the electrodeposition behavior of Fe-Ni and Zn-Ni alloys was' classified into the' 'anomalous type. In this type of codeposition, less noble metal, i.e. Fe for Fe-Ni and Zn for Zn-Ni system, deposits preferentially and the change in -the alloy composition- with the variation of electrolysis conditions was unpredictable because of their obscure deposition mechanism. Since most properties of the alloys mainly depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is neces5al)' to clarify the mechanism of anomalous codepasition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so fur, and among them the hydroxide .suppression mechanism (2), (3) has been regarded most plauslble depend on their composition, the composition of the deposited' alloys must be controlled strictly. Therefore, it is necessary to clarify the mechanism of anomalous codeposition in Fe-Ni and Zn-Ni systems: Several mechanisms have been proposed so far, and among them the hydroxide suppression mechanism (2), (3) has been regarded most plausible. According to this mechanism, it can be predicted that the codeposition behavior depends greatly on the characteristic of water solvent in this study, using methanol as a solvent, the electrodeposition behavior of the anomalous codeposition was investigated to discuss the validity of the hydroxide suppression mechanism."

Jan 1, 2000

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By E. A. Werner, A. Pichler, A. Spalek, G. Reisner, P. Stiaszny

"Interstitial free (IF) sheet steels are used for complex shaped parts because of their excellent formability. If a deep drawn part is subjected· to a impact deformation at low temperature brittle fracture of the part may occur. This phenomenon\ is called secondary work embrittlement (SWE). One possibility to characterize this material/structural behavior is the drop-weight test. The result of .this .test is a temperature at and below which a crack can initiated in a deep drawn part under the investigated set of parameters. This paper addresses the influence of the preforming process on the sus- . . ceptibili.ty of IF steels to SWE.IntroductionInterstiiial:free (IF-) steels are frequently used in the automotive industry for complex· shaped p·arts because of their excellent deep drawability. The microstructure of the steel consists of a highly ductile ferritic matrix with embedded precipitates of nitrides and/or carbides. Brittle fracture can occur in deep drawn parts, if they are subjected to a high speed deformation at lo""w temperature. This phenomenon is called ~econdary Work gmbrittlement (SWE) [1-11]. Up to now there are no standardized testing procedures available to quantify the sensibility of IF-sheet steel to SWE. Neveitheless, a reasonable testing procedure which allows to quantify the tendency of a predeformed part to SWE is necessary for further material development. A commonly used test method is the drop-weight test performed at low temperatures. In such ·tests a cone-like drop weight expands a deep drawn cylindrical cup [l-3, 6, 8, 9, 11]. From this expansion experiment the temperature is determined at and below which a brittle crack can be initiated in the deep drawn cup under the investigated impact test parameters. The highest measured temperature at which a deep drawn cup fails by brittle fracture is called frack appearances !emperature (CAPT). The lower the value of the CAPT the lower is the sensibility of a deep drawn part of IF-sheet steel to SWE. This paper aims to clarify the role of the preforming process on the impact behavior of an IF steel. For this purpose a numerical analysis of the deep drawing process and cup expansion tests are conducted."

Jan 1, 2000

By K. Itagaki, H. Henao

"The experimental study on the phase equilibrium and distribution of minor elements such as chromium and copper between magnesia saturated FeOx-MgO-SiO2 slag and Fe-Ni alloy were carried out under controlled oxygen partial pressure between 10-6-5 and 10-10 using CO and CO2 mixed gas at 1773 and 1873 K.The effect of slag additives such as lime (CaO/SiO2 molar ratio: 1) and alumina (AlO1.5/SiO2 molar ratio: 0.1) on the distribution behavior of the minor elements was also investigated.The value of distribution ratio for chromium, defined by (%Cr in slag)/[%Cr in alloy], is larger than 70 at the pO2 region conducted in the present study for the MgO saturated FeOx-MgO-SiO2 slag at 1773K. These value are almost 4-order higher then that of nickel though the distribution ratio of copper shows similar values with nickel. Analysis of the data indicates that addition of lime in the slag and the increase of temperature reduce the dissolution of chromium into the slag and the addition of aluminum increases the dissolution of chromium into the slag while reduces the dissolution of copper and nickel.IntroductionChromium. is a minor element in a nickel oxide ore but a Japan major component in the secondary material of stainless steel and is also introduced in the Fe-Ni production process due to dissolving bricks of a furnace. Chromium is a concerned matter for the beneficial utilization and disposition of ·slag because Cr6+ is a harmful element. Considering Fe-Ni as an alloy component in steel making, and the demand of high purity nickel, chromium is an -undesirable element that has to be eliminated into slag prior to the steel making, or the production of high temperature refractory alloys. On · the other ·hand chromium is an element of steel alloy for many applications, thus Fe-Ni containing chromium in minor element is desirable in some stainless steel making."

Jan 1, 2000