Search Documents

By Xiaofei Guan, Adam C. Powell, Uday B. Pal, Srikanth Gopalan

This paper reports a solid oxide membrane (SOM) electrolysis experiment using an LSM– Inconel inert anode current collector for production of Mg and O2 at 1423K. The electrochemical performance of the SOM cell was evaluated by using various electrochemical techniques including electrochemical impedance spectroscopy, potentiodynamic scans, and potentiostatic electrolysis. The effects of Mg solubility in the flux on the current efficiency and the YSZ membrane stability during SOM electrolysis were discussed and examined through experiment and modeling. The electronic transference number of the flux were measured to assess the Mg dissolution in the flux during SOM electrolysis. A negative correlation between the electronic transference number of the flux and the current efficiency of the SOM electrolysis was observed.

Jan 1, 2014

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Jie Li

Series of carbon compounds as anode materials were prepared for super lithium ion capacitor using graphite and active carbon (AC) as raw materials. Their electrochemical properties were investigated by constant current charge-discharge test. The results showed that the compound anode had good capacitive performance as well as Li-ion battery performance. The potential of the capacitor could be as high as 3.5V vs Li/Li+ when compared with 2.5V vs Li/Li+ in the AC-AC capacitor, accordingly, the energy density increased from 21.7Wh/kg to 40.3Wh/kg. The compound anode also had excellent rate performance that as the current density increasing from 0.1A/g to 1A/g,the capacitance decreased only 1.3F/g, and good cycle performance that the capacitance holding remained 96.7% after 10 times cycles even at the highest potential of 3.5 V vs Li/Li+.

Jan 1, 2009

By Hongfa Hu, Stavros A. Argyropoulos, Stephan Ferenczy

"Physical as well as mathematical modeling was carried out to investigate the exothermic mass transfer in liquid metal systems. In these systems, the exothermicity induces unique heat, mass and momentum transfer phenomena. Moreover, these phenomena are deeply coupled and they are further complicated by the presence of a moving boundary.In the physical model used, ice cylinders were immersed into sulfuric acid solutions, because the intermixing of ice with sulfuric acid is very exothermic. In this low temperature system, velocity and temperature measurements in the sulfuric acid were made as well as measurements of the ice melting in the sulfuric acid.The mathematical model developed solved simultaneously the heat, mass and momentum equations numerically, utilizing the control-volume finite difference approach. The enthalpy method was adopted to track the moving boundary. Predictions made by the mathematical model were in close agreement with the results obtained by the physical model.The results from the mathematical model were further validated with experiments involving high temperature liquid metals. Specifically, data were obtained in an experimental setup involving (a) dipping silicon cylinders into high carbon liquid iron and (b) dipping nickel cylinders into liquid aluminum. Results from these experimental studies supported the predictions of the mathematical model."

Jan 1, 1999

By Stavros A. Argyropoulos

Exothermic mass transfer takes place in various areas involving metallic systems, ranging from liquid metal processing operations to the growth of thin films in microelectronics. The formation of intermetallic compounds plays an important role in the exothermic mass transfer of metallic systems. Two types of exothermicity are identified , namely , Microexothermicity and Macroexothermicity. The former is encountered when small amounts of metals are mixed, while the latter is exhibited when a solid metal in a lump form is added into liquid metal. In this paper two types of exothermic mass transfer in metallic systems will be presented and reviewed. Mathematical modelling work for these types of exothermic mass transfer will be analyzed.

Jan 1, 1993

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By Fathi Habashi

While it is commonly known that the precious metals and to some extent copper occur in the native state, it is less known that mercury, iron, nickel, and cobalt do occur also in the native state; the last three (Fe, Ni, and Co) usually occur together in form of an alloy. The particle size varies greatly from less than 10 microns (gold and mercury) to about 400 tons boulders (copper).

Jan 1, 1993

By Oluwatosin A. Aladejebi, Apsara S. Jayasekara, Raymond J. Longbottom, Mark Reid, Marc in het Panhuis, Brian J. Monaghan

The coke analogue is a new research tool that has been developed to quantify and characterize the effect minerals in coke have on coke reactivity. The analogue material is made from a number of different carbon or carbon containing materials and minerals to in part replicate real industrial coke’s reactivity behavior. Elucidation of the effects of minerals on coke reactivity has proved difficult due to the complex and heterogeneous nature of industrial coke and the potential non-additive effects of minerals on coke reactivity. The coke analogue addresses this complexity and heterogeneity through control of its mineralogy, mineral size and mineral dispersion through the analogue, porosity and carbon structures. Initial studies using the analogue were focused on coke dissolution kinetics in liquid iron but recent work has focused in characterization of its porosity, carbon structure and rate of reaction.

Jan 1, 2014

By Albaharna O. T., Argyropoulos S. A.

"This paper describes the development and the implementation of process control in a variety of instruments used in metallurgical laboratories. These instruments are used for different research projects in extractive metallurgy. Hardware and software aspects for this implementation are described and analyzed. Extractive metallurgy applications where process control was .used are presented. IntroductionMicroprocessors are invading almost every area of our lives and are turning up in unexpected applications. A great deal of new equipment which is coming into the market have built- in microprocessor systems. Nevertheless, the area of upgrading existing processes has been slow to develop. There are a variety of reasons for this, and many of these are economic. One of the principal reasons, however, is the general reluctance on the part of many organizations to commit a strong effort to put this new technology into their existing processes.Microprocessor systems developed ""in lab"" are capable of not only measuring thermophysical events which are taking place in metallurgical furnaces, but simultaneously controlling these furnaces. In this paper software and hardware aspects in the implementation of microprocessor control for resistance and for induction furnaces are presented. In addition to this, metallurgical results are given from experiments where this furnace control was applied."

Jan 1, 1989

By J. P. Schde

The authors deal with nickel production and usage patterns, nickel's first-use and end-use, examples of nickel applications in modern technology, e.g., energy generation and conservation, environmental protection, the oil and gas industry, construction and machinery, food production, conservation and distribution, consumer durables and the like. A special section of the paper is devoted to new applications of nickel in the electronic industry, modern corrosion control and the building and construction industries. The need to defend traditional markets for nickel while striving to find new applications, is also stressed.

Jan 1, 1988

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By Z. Sun, H. A. Davies

"Current understanding of the mechanisms by which glassy and crystalline thin ribbons are formed in high speed continuous casting processes is considered. A computer model of the combined heat and momentum transfer during melt spinning has been developed. The influence of roll velocity and of heat transfer coefficient (between the melt and the roll) on the temperature and velocity distributions within the melt puddle is analysed and the thickness of the extracted ribbon computed. The relative importance of heat and momentum transfer under different conditions is assessed and differences between the casting of crystalline and amorphous strip highlighted.IntroductionHigh speed continuous casting of thin metallic ribbon and strip is currently of considerable interest both to metal processers and to those studying process mechanisms. The practical interest arises both from the potential economic benefits to be gained from a shorter and more energy-efficient production route and from the ability to obtain extended and uniform thin strip having a metastable microcrystalline or amorphous structure with enhanced or unique properties. The latter arise from the rapid solidification associated with the cooling of very thin sections of melt brought into intimate thermal contact with one or two rapidly moving heat sinks.The principal processes for casting thin strip include free jet, chill-block melt-spinning (GBMS) (1), melt drag (MD) (2), planar flow casting (PFG) (3) and twin-roll casting (TRG) (4). For the first three of these, all essentially variants of melt-spinning, melt flows through a nozzle onto the circumferential surface of a rapidly rotating roll, whereas for TRG the melt passes into the nip between two contra-rotating rolls. We shall be concerned in this paper with the single-roll melt spinning processes only. For these, a puddle is established where the melt contacts the roll surface and the length of this puddle l is a function of the process conditions, notably the circumferential velocity of the roll Us and the volumetric flow rate of the melt Q. The contact time between any point on the roll surface and this puddle, or residence time eR(= l /Us) determines the thickness of ribbon t extracted from the puddle. This thickness, in turn, partly governs the cooling rate T and the amount of undercooling in the melt and thus the microstructure of the solidified ribbon."

Jan 1, 1986

By David G. Dixon, Maziar Eghbalnia

"Gold and silver nanoparticles (NPs) were deposited on pyrite at ambient temperature from colloidal solutions prepared by reduction of hydrogen tetrachloroaurate or silver nitrate by sodium sulfide or sodium tetrahydridoborate. The nanoparticles were characterized using Ultraviolet-Visible (UV-Vis) spectroscopy and the experimental spectra were fitted using Mie - Gans modeling. The modified pyrite was investigated using Electrochemical Impedance Spectroscopy (EIS). Electrodes were prepared from both natural and modified pyrite samples and were modeled using an equivalent circuit (EC) based on the EIS data. The comparison of the results revealed a decrease in charge transfer resistance for the ferric ferrous redox couple associated with the modified pyrite. From this behavior it is concluded that the electronic transport between the nanoparticles and the electrode surface over distances in nanometer scale is enhanced. Nanoparticles below a certain size act as quantum dots due to electronic confmement. Decreased charged transfer resistance at the nanometer scale may be caused by electron transport through tunneling mechanism via quantum dots.IntroductionIn recent years, considerable attention has been focused on the synthesis and study of Metal nanoparticles due to their potential applications in the fields of physics, chemistry, biology, medicine, material science and their interdisciplinary fields[!]. When material is nano-sized, the physical properties deviate markedly from those of bulk material, however, this effect is highly dependent on the particle size, interparticle distance, and morphology of the nanoparticles [2].An extremely small region of space defmed in a semiconductor material in order of nanometers is called a quantum dot, a term coined by Reed [3]. The three dimensional confinement of quantum dots can change properties of the excitons in comparison to free excitons in a bulk material [4]. Nanoparticles behave electronically as zero-dimensional (restricted in all three dimensions) quantum dots when the de Broglie wavelength of the valence electrons and the particle are in the same size range.As Reed [3] explains electrons confined in a plane have no freedom to move the third dimension. Those confined in a quantum wire are only free to move in one dimension, and those confined in a quantum dot are not free in to move in any dimension. An electron inside a cube of material IO nm on a side is confined to a point."

Jan 1, 2012

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By Sven Reutzel

Investigations show that Co-based melts embedded by glass flux in a crucible can be under- cooled nearly as strong as samples processed containerlessly by electromagnetic levitation. This allows to measure magnetic susceptibility on undercooled melts while combining the use of a Faraday-balance and undercooling technique. The magnetic susceptibility of Co and Co-based alloys (such as Co-Pd and Co-Cu) is investigated as a function of temperature from superheated to undercooled state. This is done by measuring the change of magnetic force F, on a sample in a constant magnetic field Bo and an additional gradient field by means of a Faraday-balance. When liquid Co-based alloys are undercooled the magnetisation steeply rises if temperature approaches the Curie temperature. The magnetisation is measured for some Co-based alloys in liquid state as a function of alloy system and its concentration. The results show that the magnetic susceptibility of the liquid undercooled samples follows a Curie-Weiss behaviour, from which Curie temperature and magnetic moments for the liquid state are inferred.

Jan 1, 2002

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By L. R. Verney

A number of interrelated factors influence the economics of the sulphide smelting of copper, lead, zinc and nickel. This paper discusses these factors, mainly from a US point of view, and shows how they affect the cost of construction and operation of new and existing plants. The paper shows how metallurgical plant construction costs and the consumer price index have increased at a much faster rate than metal prices thereby making some metal mining and production operations within the USA, Canada and the EEC less profitable than operations elsewhere. This in turn inhibits new "grass roots" metallurgical developments. It is explained how retrofit of existing pyrometallurgical plants can be a more viable development than the construction of "green field" plants, especially if such retrofit improves, energy efficiencies, overall operating costs and reduces emissions of sulphur and other toxic wastes. Some aspects of metallurgical plant operation are examined, especially for copper and nickel, to show how changes in operating practices may develop in order to improve overall smelting economies, especially when developed in conjunction with objective retrofit. The paper also examines some financial aspects, especially insofar as the disparity between terms for loans offered to third world countries and the USA and the EEC are concerned and also comments upon the need, especially within the USA, for legislation to permit rapid depreciation of capital. Specific comments are made about environmental aspects, including the lack of uniformity of pollution control legislation and how environmental considerations may have some bearing of the location of future smelting operations.

Jan 1, 1983

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005