Search Documents

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Luis W. Pommier

Large quantities of sea sludge containing halogenated organic compounds, such as PCB, oils and metals like arsenic and lead have accumulated throughout the years at the bottom of sea channels and harbors and are obstructing navigation and creating environmental problems which need to be resolved. A sludge from a California port would be dredged by suction pumps, it would be processed in a plant which would be built either on firm soil or on floating platforms. The sludge shows contents of up to 1 ppm of PCB, 15 % oil and 10 ppm of arsenic, which generates a very fetid odor. Bench scale work indicates that most of the contamination concentrates on the solid phase, in fact, only minor amounts of oil report to the sea water and can be readily removed by physical means. After separation of the sea water from the solids of the sludge by decantation, it is possible to solubilize the PCB, the oil and the metals into an organic solvent leaving a non-hazardous soil for disposal near the harbor. The PCB is dehalogenated during the solubilization process leaving a liquor solution containing the oil and metals. The oil is extracted leaving an aqueous solution containing the arsenic. Further process extracts the arsenic from this solution rendering the liquid non-hazardous. Transportation and disposal of the sludge is impractical. There are hundreds of thousands of tons of hazardous soils accumulated in each harbor, which would fill the hazardous waste disposal sites available and it would be, prohibitively expensive to do so. It is not possible to compare the costs of decontamination with a competitive method. If it were, the proposed process would be less expensive than transportation and disposal and it has the advantage of removing the liabilities from the Responsible party. After a full scale continuous pilot project is run to decontaminate a small, 500 cubic yards accumulation of this type of sludge in a California harbor, a full scale environmental project would be initiated. The decontamination of one million tons of sludge would be completed in five years.

Jan 1, 1995

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Ah03 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and pO;, in a range between 2.5x,IO,2 and 10.1 Pa by using CO-C02-S0Z gas mixtures. The content of nickel in the slag at POz of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4.1 mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 0.2 mass%, respectively. It was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy. The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-AI20) based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial' pressure.

Jan 1, 2003

By Hector Henao

To provide thermodynamic data for converting the nickel matte to liquid nickel, an experimental study was conducted in the phase equilibrium between the Ni-S alloy and the CaO-Al2O3 based slag melted in a MgO crucible at 1873 K under controlled Pso2 of 10.1 kPa and Po2 in a range between 2.5x 10-and 10.1 Pa by using CO-CO2-SO2 gas mixtures. The content of nickel in the slag at Po, of 10.1 Pa, above which solid NiO is expected to precipitate in the equilibrium state, was found to be 4, I mass% and the contents of sulfur and oxygen in the nickel melt were 0.4 and 02 mass%, respectively. ft was clarified that increase in the temperature reduces the solubility of nickel in the slag and the contents of sulfur and oxygen in the alloy, The distribution of minor elements such as gold, silver, copper, cobalt, iron, arsenic and antimony between the Ni-S alloy and the CaO-Al2O3 based slag was also studied. The distribution ratios of iron and cobalt, defined by (%X in slag)/[%X in alloy] where X is the minor element, are larger values than that of nickel, while those of copper, silver and antimony are similar to that of nickel. The distribution ratios of arsenic and gold are lower than that of nickel in the higher range of oxygen partial pressure.

Jan 1, 2003

By Hong Yong Sohn, Miguel Olivas-Martinez

"Different approaches are used for calculating the ‘energy requirement’ of a process. The determination of energy requirement becomes confusing for a process in which a fuel is also a reactant. The key issue is which heat of chemical reaction should be included in the ‘energy requirement’ value. We will use the example of ironmaking processes to illustrate the problem. The different approaches essentially boil down to the question: does one include the combustion heat of the reductant used in the reduction reaction or just the heat of the reduction reaction? Depending on the viewpoint, either approach can be accepted; it is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of a process depends on the choice. The energy requirement of a novel flash ironmaking process will be compared with that of an average blast furnace operation.IntroductionDifferent approaches are used for performing energy balance calculations and perhaps more significantly in presenting the ‘energy requirement’ of a process. The question becomes more involved for a process in which one or more reactants are also used to generate the process heat by combustion. Often the key issue is which heat of chemical reaction to include in presenting the ‘energy requirement’ of the process.It is worthwhile to note at the outset that the difference in energy requirements between different processes for converting similar raw materials to the same desired product is largely unaffected by the choice of chemical reactions to be included. However, the absolute value presented as the ‘energy requirement’ of a process can be different by a large amount depending on the approach. We use the example of ironmaking processes to illustrate the problem. In these processes, as currently practiced or under development, carbon and/or hydrocarbons (including hydrogen) are used as the fuel as well as the reactant for reducing the iron oxide mineral.The different approaches in this case essentially boil down to the following question: does one include the combustion heat of the reductant used in the reduction reaction or treat the reductant portion as just a reactant? Depending on the viewpoint, either approach can be considered acceptable. It is a matter of convention. There is a need, however, to select a standard approach because the absolute value of ‘energy requirement’ of an ironmaking process (e.g., the currently dominant blast furnace process) depends on such a choice. It is particularly important to clearly state the specific approach used when the energy requirement of ironmaking is compared with those of other industrial processes such as petrochemicals production."

Jan 1, 2014

By Xu Weimin

The existing copper electrorefining tankhouse of Jinchuan Nonferrous Metals Complex (JNC) was commissioned in 1986 for refining blister copper anodes. Blister copper is produced by reverberating chalcocite separated from converter high grade nickel-copper matter by means of flotation. Special chemical analysis of the anodes shows, a composition of 93.02 - 95.72 % copper, 3.0 - 4.96 % nickel and 0.5 - 1.23 % sulfur. The wide range of composition makes the electrorefining process fairly different from others throughout the world. The initial nickel content of 20 ppm and sulfur 40 ppm or more in copper cathodes are reduced to 8.5 ppm and 11 ppm respectively. Since 1986 the tankhouse has undergone significant evolutionary modifications and implementations to ameliorate cathodes quality desirably. The important fact is that the N-additive was utilized through many studies and pilot and field trials successfully. While our primary purpose is to improve chemical quality of the cathodes, tankhouse capacity is increased considerably and the process is perfected satisfactorily. The tankhouse is described with special emphasis on JINCHUAN PROCESS. The upgrading of our product by the utilization of the N-additive is highlighted. The other aspects of the tankhouse including spent electrolyte treatment and by product nickel sulfate manufacturing are briefed as well. Key words: JINCHUAN PROCESS, anode, cathode, electrolyte, electrorefining, N-additive.

Jan 1, 1993

By Yoshinao Kobayashi

he removal of oxygen from titanium and zirconium is important for use in application because it significantly affects the mechanical and physical properties such as ductility and toughness. However, thermodynamic properties of oxygen in molten titanium and zirconium have not been clarified and the effective deoxidation process of molten titanium and zirconium has not been established. In this study, the standard Gibbs energy of reaction of oxygen and yttrium in molten titanium and zirconium have been measured by a chemical equilibrium technique. Molten titanium, zirconium, and their alloys with aluminum were equilibrated with a Y2O3, A12O3, or Zr02 pellet in a cold crucible. The results are summarized as follows:

Jan 1, 2000

By Kuniaki Murase, Tetsuji Hirato, Yasuhiro Awakura

"Electrodeposition of CdTe was studied using aqueous ammonia-alkaline electrolytic baths in which Cd11-and Te1V-ions are dissolving as Cd11(NH3)/+ and Te1vol-ions, respectively. Ca-thodic polarization curves of the baths suggest the presence of strong interaction between the Cd11-and Te1V-ions; electrodeposition of tellurium is inhibited by the presence of Cd(NH3)/+ ions. The interaction makes it possible to electrodeposit CdTe films with stoichiometric composition. Polycrystalline CdTe thin film of about 1 µm thickness was electrodeposited at 343 K from ammonia-alkaline solutions (pH= 10.7) containing TeO32-(<20 mmol dm-3) and Cd(NH3)/+ ( < 60 mmol dm-3) ions. Increasing Cd(NH3)/42+/TeO32- mole ratio or decreasing total concentration of ammonia/ammonium-ion gave flat and smooth crystalline CdTe deposits at constant cathode potential-0.70 to -0.30 V vs SHE at 343 K.IntroductionCadmium telluride (CdTe) is well-known as a compound semiconductor whose band gap, i.e. 1.44 eV, is suitable for solar energy conversion with a photovoltaic cell. Various methods, such as CVD (chemical vapor deposition) and electrodeposition, of preparing CdTe thin films for solar cells have been investigated.Acidic sulfate solutions with a pH of 1-2 are usually employed for CdTe processing by electrodeposition.1-3) The electrodeposition of compound semiconductors is usually achieved (i) at a higher cathode potential than the redox potential of less-noble species, can in this case, and (ii) under the condition of diffusion-limiting current of a more noble species, Te1Y.4) There-fore, a suitable CdII/TeIV concentration ratio in the acidic electrolytic baths, resulting in the deposition of stoichiometric CdTe, is determined by the diffusion-limiting current density of TeIV- reduction, i.e. the concentration of HTeIVO2+ · Since the solubility ofTe1v species HTeIVO2+ in the acidic solutions is quite low, the rate at which CdTe is deposited from the acidic solutions is extremely slow."

Jan 1, 1998

By G. Nazari

ERAMET, through its subsidiary COMILOG, have rights to a rich niobium and rare earth deposit inGabon. The Mabounié deposit, is located 50 kmfromthe town of Lambaréné, in a fairly remote location. ERAMET has been developing a process to recover value metals for several years, and approached Hatch Ltd. to design a sizeable Demonstration Plant to help them further optimize the process, and prove the flowsheet is technically viable. The process employs concentration techniques to recover an upgraded Nb/REE feed material for processing in the subsequent leach step. Rare earths and niobium are selectively leached, and subsequently precipitated. Following precipitation, rare earths undergo bulk separation and are purified to produce LRE and mixed MRE/HRE products, which will be further processed by Third Parties. This paper provides a high-level overview of the process, summarizes the motivation for a Demonstration Plant in the vicinity of the deposit, and discusses technical challenges faced during the flowsheet definition and design phase. Key challenges are focused on and summaries of the methodologies used to address each challenge, as well as the solutions to overcome the challenges, are discussed. The paper provides motivation for further process simplification and concludes with a project update.

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By John J. Moore

This paper discusses the application of a video technique to construct stability diagrams for the combustion synthesis of ceramic-metal composites. Several model exothermic combustion synthesis reactions have been used to investigate the effect of the reaction parameters, eg. stoichiometry, green density, etc, on the stability of the propagating combustion reaction front and subsequent product morphology. The effect of varying the reactants and their stoichiometry to provide a range of reactant and product species ie. solids, liquids and gases, in the synthesis of both dense and expanded (foamed) ceramic and ceramic-metal composites was also investigated with respect to their corresponding combustion front stabilities.

Jan 1, 1993

By Jose M. Gomez-Vega, Osamu Takai, Atsushi Hozumi, Hiroyuki Sugimura

"Ongoing research is reported aimed at improving the properties of mesoporous silica-based coatings on various substrates for optoelectronic or medical applications. Tetraethylorthosilicate (TEOS) was selected as the silica precursor, and amphiphilic triblock copolymers poly( ethylene oxide)- poly(propylene oxide)poly( ethylene oxide) as the surfactant micellar template or structure-directing agents. Cetyltrimethylammonium chloride (CTAC) was also used as a control agent. The effect of the templating agent and type of substrate (glass, Si, and Ti) on the mesoporosity, particularly on the alignment of the mesochannels, has been investigated. Three · different treatments (thermocalcination, photocalcination, and solvent extraction) have been also studied to remove the organic templates.IntroductionThe fabrication of mesoporous silicate-based materials through the utilization of a sol-gel process, where cooperative organization of organic and inorganic species takes place, provides a versatile approach to nanoscaled structures with potential applications in fields such as catalysts, optoelectronics, biomaterials, etc. Compared to conventional low molecular weight surfactants, self assembly of amphiphilic·block copolymers can result in mesostructured materials with larger pore sizes (up to 30 nm).1 Most of the synthetic strategies use silicon alkoxides as the silica precursor, although non-silicate metal alkoxides, e.g; Ti, Zr, Al, and B, have been also used to obtain different mesoporous materials, or even mixed metallic oxide systems. 2 Recently, Yang et al. 3 • 4 were able to synthesii:e a great variety of mesoporous metal oxides ID nonaqueous media using inorganic precursors (metal chlorides) and block copolymers as structure-directing agents."

Jan 1, 2000

By K. R. Robilliard

An outline is given of the problems facing tlile lead and zinc industry from the viewpoint of the range of residues currently produced from electrolytic zinc, blast furnace and other processes. Smelting approaches available using top submerged lancing technology are discussed and analysed. Pilot plant results for a range of lead and zinc-bearing materials are presented.

Jan 1, 1992

By M. Potesser

In the primary and secondary copper industry the anode furnace is the most important process step in the refining procedure to reach an enhancement in value and quality of the copper by a selective oxidation and reduction. By combining the advantages of the conventional tilting hearth anode furnace and the benefits of the drum type anode furnace a new aggregate was developed and patented. The cross-section of the furnace is elliptical and the whole unit is tiltable. During the melting period, the contact surface between the burners and the bath or the scarp is enlarged - an increased energy input is the consequence. For the refining period the furnace is rotated, whereby a high bath level is guaranteed. Due to the longer residence time of the gas in the copper melt, not only the gas consumption is reduced but also the efficiency/quality of the refining process is improved. This investigation shows a metallurgical comparison between the new anode furnace concept with the elliptical profile/cross section and the conventional, tiltable hearth anode furnace as well as the drum type anode furnace. The CFD modeling of the currents in these different furnaces delivered helpful data to compare the geometry of the different furnaces. The investigation covered the refining of blister copper from primary metallurgy, from secondary metallurgy as well as from a mixture of both copper melts. The paper underlines the possibilities for a reduction of the tap-to-tap time and for an increase in production capacity, which can be achieved by applying the new furnace concept in comparison to the conventional furnaces.

Jan 1, 2006

By Jürgen Antrekowitsch

Typical zinc oxides recovered from wastes like steel mill dusts and neutral leaching residues are of a low quality because of impurities like fluorine, chlorine, lead and others. Therefore, they are not comparable to technical grade zinc oxides produced in “French” or “American Process”. Some new developments, most of them still in pilot scale, try to establish processes where higher qualities of the product should be achieved. Zinc oxides are not only supposed to be an input material for electrolytic zinc production. Far more, they should find their way into the zinc oxide market as a substitute for technical grade zinc oxides. Furthermore, a new field of application for these oxides has been investigated at the department of Nonferrous Metallurgy, University of Leoben. Because of a higher acceptance concerning different impurities in relation to zinc winning electrolyses, a use in electrolytic galvanizing shows an interesting option. Therefore, synthetic zinc oxides with different impurities were generated to study the effect of these impurities especially on the quality of the zinc layer. Typical steel sheets, as used for car bodies, were electrolytically galvanized and the resulting layer was analysed, as main impurities compounds of fluorine, chlorine, iron, lead and calcium were used for the investigations. Beside the layer quality, the current efficiency and the possible galvanizing speed were examined. The results give an indication, weather such an alternative application can be feasible from a technical and economical point of view or not. 597

Jan 1, 2008