Search Documents

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By Revendra Awasthi

The application of a horizontal inclinometer and a tiltmeter to measure tilt, curvature, and deformations of shallow footings during mine subsidence is described. The measurements were taken during mining of a longwall panel in Southern Illinois and were supplemented with precision level survey data. Monitoring was conducted under a cooperative agreement between the Institute for Geotechnology at The University of Tennessee, Knoxville, the U.S. Bureau of Mines, the National Science Foundation, the Illinois Mine Subsidence Insurance Fund, and Old Ben Coal Company. Six different footings were constructed and instrumented at two sites; one above the panel centerline, and the second inside the edge of the panel in the anticipated zone of maximum tension. A brief description of the inclinometer casing and tiltplate installation is described, and the results obtained from the two instruments on a plain concrete footing compared. Observations of footing deformations and curvatures calculated from the inclinometer and tiltmeter data are also presented, and the results compared with observed structural damage.

Jan 1, 1990

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks' operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By C. W. Bollier

In recent years, Peabody Coal Company has enjoyed a great amount of success using roof trussing as a secondary support system. Since 1975, over 180,000 trusses have been installed in 12 different Peabody mines with varying geological conditions. Projections from Peabody, and throughout the mining industry, indicate a continuous growth in the trussing principle for roof control. Peabody's primary supplier has sold over 1,000,000 trusses to 50 different mines throughout the country. (1) Roof trusses provide an improved means of controlling difficult roof conditions which, in turn, improves worker safety and mine production. Since the original development of the truss, (2) the only major modification to the trussing procedure has been the addition of the resin point anchor system in the mid-70's. The resin point anchor was the catalyst needed to provide a reliable anchor and create acceptance of the roof truss by both management and labor. Peabody began using trusses in their mines in 1975. For the first few years, most of the truss effort was geared toward determining proper anchorage, spacing, and gathering historical data. In recent years, Peabody's activities have centered on the development of improving trussing procedures. Through monitoring and trussing activities, a number of areas of improvement have been found.

Jan 1, 1982

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By Ali Benbia

The paper shows results from the physical modelling of longwall excavations concentrating on the fracture pattern development above longwall panels. The modelling technique is briefly described and the detailed analysis of the fracture pattern is discussed. The physical modelling is particularly useful in visualising the caving process above longwall panels. This advantage has been exploited using the image analysis technique. Black and white pictures have been taken while the models are tested in successive stages and then enhanced and stored as binary images by scanning using an image analyser coupled with a video camera. These images are then processed using a custom C program which allows the discretization and characterisation of the fractures. This provides a valuable data base for further numerical and statistical analysis which subsequently may allow the assessment of the water inflow hazard to the workings. In this paper a sequence of different extraction thickness have been analysed using the technique mentioned above to show the effect of the extraction thickness on the fracture distribution and intensity.

Jan 1, 1993

By Herryal Anwar

The application of roof bolting technology to control the stability of roadways in coal mining within weak strata or under high ground pressure has improved progressively. One of several factors that affect the design of rock bolting is the immediate roof characteristics of the roadway. On the competent rocks, the mining conditions may indicate a high level of stability and a low density of bolting patterns may be adequate to control the ground stability. However, at a weak strata, the roadway will be affected by both horizontal and vertical stresses that may generate a high level of deformation in the immediate roof. This sensitivity of the roadway will require a mine plan design which consider the pillar sizes and sequences of extraction as well as a conservative reinforcement to maintain the integrity of the deforming weak roof strata. Rock bolting technology has been used to maintain the stability of roadways in Indonesia and Japan for a few years. In this paper the overview of the application of rock bolting reinforcement in Ombilin Coal Mine, Indonesia and Miike Coal Mine, Japan is given.

Jan 1, 1999

By Craig Compton

The The National Institute for Occupational Safety ane Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 518-inch bolts; A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 R of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially- overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

Jan 1, 2005

By Christopher Mark

The past decade has provided a wealth of practical experience with longwall pillar design. Design formulas developed specifically for longwalls have proven their value in numerous applications. Analytic methods, including numerical models, have a1 so made important contributions. These advances have been based on basic research into abutment loads, coal pillar mechanics, and the interaction between pillar performance and entry stability. The goal of this paper is to review the state of the art in longwall pillar design from the standpoint of the practitioner. Actual case histories are presented to illustrate the current capabilities and limitations of pillar design methods. The paper also discusses the advances that can be expected in the future.

Jan 1, 1990

By Jiacheng Wang

The current state of thick seam coal mining methods is illustrated in three typical cases of thick seam longwall mining, each pointing out the outstanding achievements in top-coal caving mining and large cutting height mining in China. At the same time, based on current thick seam mining practices in China, some problems urgently need to be solved. These include improving the recovery ratio of coal reserves, determination of overburden strata pressure, shield support selection, supporting methods for large cross-section in-seam roadways, top coal bulk flow theory, and gas flow and control technology. In addition, the rational production capacity should be studied from both economic and technological perspectives in order to optimize coal recovery and efficiency.

Jan 1, 2011

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By J. D. Dizon

Conventional strata control methods (i.e. roof bolts. cable trusses) are not always effective for ground control of very weak coal strata. An alternative method, termed presupport. is being investigated by the U.S. Bureau of Mines. In this paper structural modeling of presupport conceuts and field teatinn of a DresuDuort application is presented. Pinite-elem&; modeis indicate that forepoles significantly lower beam stresses in the roof strata overlying a coal seam. but they cannot he expected to prevent or reduce I roof strata failure at the coal face due to the presence of a high stress concentration at that location. However, their presence near the coal face is needed to sustain the fall of roof if it does occur. Because of an ever present severe stress concentration at the coal face, it would appear that stresses could exceed material strengths, causing local structural damage, especially if the rock is very weak. Therefore previous coal face positions along an entry may have a higher than normal probability of roof fall. In the field investigation. a loorcost air injection test has thus far shown promise as a tool for evaluating that effects of forepoling on the roof strata. Observations of coal mine en- tries in which forepoles have been installed indicate forepoling is effective in controlling very weak roof strata.

Jan 1, 1990

Case study data were analyzed to develop and quantify empirical stress transfer relationships between seams for both longwall and room and pillar mines. Layering in the innerburden and the distance between seams were determined to be the controlling factors. To evaluate the effect of bedding planes on stress transfer, laboratory studies were conducted using layered, low modulus gravity loaded photoelastic models. Parameters investigated were thickness, number of discrete layers, modulus and friction between layers. Results showed that there was significant distortion of the pressure bulb in highly laminated conditions which correlated with the results of empirical analysis. Relationships developed were used to modify the results obtained from numerical modelling between multi-seam longwall operations. Research conclusions were demonstrated using case studies.

Jan 1, 1995