Search Documents

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Peter Griesenbrock

In German underground coal mining mostly arch and some rectangular roadways are used in the development work. Due to its positive results from numerical and physical modeling techniques as well as good underground experiences, the numbers of rectangular roadways has increased significantly. Today the bolt support - independent of its cross-sectional shape - represents an undeniable support element. During the introduction of new bolt techniques a detailed investigation of the rock and support mechanical effectiveness of bolt support in roadways at all operation stages is of basic importance. This effectiveness can be predicted and verified using different simulation techniques. For the planning of rockbolted roadways two supplementary simulation techniques are presented in this paper. By combination of all available planning tools the best result for planning assurance can be achieved. Keywords: numerical modeling, physical modeling, arched roadway, rectangular roadway, roofbolting, advancing longwall.

Jan 1, 2002

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By Rusty Mchenry, Craig Dickerson, Robin L. Oldham

"It has been proven that longwall faces can be moved safely and efficiently. However, abutment pressures and poor ground control conditions can halt operations and be hazardous to coal miners. Recently at a mine in Southwestern Pennsylvania, roof material collapsed above shields that created two large voids and caused major challenges for shield recovery. A unique, engineering solution was developed that utilized a modified concrete material to fill the voids, creating stability in the affected area. The many phases of this project included the construction phase, void pumping, cutting out, and bolting of the concrete material. This project eliminated the hazards associated with bolting the recovery face and removing shields in adverse conditions, making it possible for the mine operator to safely complete the longwall move.INTRODUCTIONFrequently in the mining process, especially during the recovery phase, voids above the longwall supports have occurred. These voids are simply roof cavities caused by falling rock strata above the longwall face. Most often, this condition slows down or halts mining operations and creates hazardous work conditions for coal miners. Numerous methods of supporting void areas on longwall faces have been attempted and utilized throughout the mining industry since the advent of the longwall mining system. These methods have utilized many different materials and processes and have included the installation of steel or wooden beams, crib blocks, and various types of roof bolts. However, these methods can be dangerous due to exposure of personnel to the mine voids, falling roof material, and the necessity to handle large amounts of heavy support materials.This paper describes a unique case study in Southwestern Pennsylvania where longwall recovery methods, through two void fills, were successfully completed, eliminating exposure of coal miners to the rock voids above. At the start of this endeavor, normal recovery operations were halted, and hazardous conditions became a concern when the voids were encountered. However, in the interest of safety, the decision was made to try a unique method to completely fill the void from the bottom of the coal seam to the top of the void with a cementitious material and then mine through it. This is in contrast to traditional methods where beams and support materials are used to stabilize the area above and in front of the mine shields, which can expose miners to the void above."

Jan 1, 2015

By Alan A. Campoli

"Pumpable crib support for longwall gates and ventilation bleeder entries is becoming more prevalent in United States coal mines (Figure 1). The pumpable crib selection and spacing design has been greatly refined by the full-scale testing conducted at the National Institute for Occupational Safety and Health (NIOSH) Mine Roof Simulator. The peak load on 24-, 27-, 30-, and 36- inch diameter J-Cribs is, on average, 300, 400, 450, and 650 kips, respectively. Standard J-Cribs have useful deformation of approximately 8 inches. The maximum useful deformation can be extended to 18–20 inches with an exterior reinforcement layer or an interior double wall, for all four J-Crib diameters. J-Crib diameter is primarily limited by a maximum 4.5:1 height-to-diameter aspect ratio. Spacing is controlled by immediate roof stability, anticipated pillar deformation, and roof bolting practice. Approximately 500,000 J-Cribs have been successfully placed in 18 different United States longwall coal mines. The selection and spacing of the J-Crib utilized to date is summarized for each mine.IntroductionLongwall productivity and safety depend on ground stability in gate and ventilation bleeder entries. Numerous support technologies have been developed and employed in United States longwall mines since the 1990s to replace traditional wooden cribbing. Many, if not all, of these technologies have been evaluated at the NIOSH Pittsburgh Research Laboratory since the mid-1990s (Mucho, et al., 1999). The NIOSH Mine Roof Simulator has a 3,000-kip vertical load and 24-inch displacement capacity, which has facilitated in-depth analysis of complex multimaterial support technologies like the pumpable crib. The extreme cost and human exposure risk associated with modern longwall mining prevent the trial and error development that would have been required absent the Mine Roof Simulator research. As a direct result of this research, pumpable cribs are becoming a major component of the standing support industry, providing the peak capacity and extended deformation characteristics necessary for successful gate and bleeder support. Recent research by Zhang, et al. (2012) and others have defined the required performance characteristics."

Jan 1, 2015

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By B. (Mamas) Das

A project to evaluate the suitability of point Load strength tests for testing and classifying coal measure rocks for coal mining application was initiated by Canada Centre for Mineral and Energy Technology (CANMET). A summary of this study with emphasis on the important findings is presented in this paper. The instrument as used in this study is a Robertson Research Rock Strength Index Log. Because of the variation in the correlation ratio between uniaxial compressive strength and point Load strength index for hard rocks and soft rocks it was decided to establish this corre¬lation initially on cement concrete specimens specially prepared for this purpose following ASTM specifications. These specimens are expected to represent soft rocks and at the same time would be of uniform quality. Once a general trend of this correlation was established tests were performed on coal and rock samples from the sub-bituminous and bituminous coalfields in Canada. The most important results may be stated as follows: (i) Generally, the common value of the ratio between the uniaxial compressive strength and the point load strength index ranges between 8 to L4. (ii) The Robertson Research Rock Strength Index Log proves to be quite suitable for testing sandstone, siltstone and some coals from the bituminous coalfields but problems have been experienced when testing weathered samples or samples from the sub-bituminous coalfields. (iii) In some cases tests were successful if Larger samples from weathered zones or from sub-bituminous coalfields were used. However, a magnified load gauge for 0-3KN or 0-5KN is expected to be the best solution for soft and weathered rocks in most of the cases. Some mudstones and some rocks from weathered zone do not appear to be suitable for these tests. This aspect of the study is still under investigation. (iv) Deterioration of rock properties due to weathering has been determined through tests on samples collected from weathered and unweathered samples.

Jan 1, 1984

By H. N. Maleki

Extensive measurements and underground observations in three Western U. S. coal mines are integrated in this paper to determine in-situ pillar load-deformation characteristics for narrow (30 it wide, 80 ft long) pillars in two-entry gate road systems. In spite of similarities in the regional geology, coal pillar laboratory mechanical properties and gate pillar geometries, the pillar peak strength, post-failure behavior, and failure mechanism were shown to be significantly different. Pillar peak strength was shown to be dependent on depth at one site, approaching burst-prone stress levels of 4000 psi. At another site, the pillar peak strength was lower because of lower confinement; this was related to the higher frequency of cleats and the lower friction- al properties of the roof/floor and coal contact. Two failure mechanisms were identified - one in the pillar, and the other in the mine floor. The roof stability was good at all three sites because of the thick-bedded nature of the roof strata and limited total gate span in a two-entry system. Existing pillar design techniques were shown to be inadequate for design, requiring adjustments for depth of cover, cleat frequency, and roof /floor frictional properties.

Jan 1, 1988

By Peter Zhang

As simpler and easier reserves are exploited to depletion, underground coal mining continues in more complex geologic settings and conditions. Roof bolting for long-term entry stability is always a challenge. For long-term entries of a mine such as belt, track entries and return airways, roof could be under-supported if one uses the same bolting plan as in short-term entries or even seem over-supported with increasing use of longer, stronger bolts along with mesh, pans, straps or trusses. In most underground coal mines, roof deteriorates over time with cutters developing deeper in entry corners; roof sagging and popping out between bolts; entry width increasing due to rib sloughage; and separations developing deeper up into the roof. In deteriorated long-term entries, roof falls could occur at certain locations and re-bolting could be costly or sometimes unfeasible. Therefore, it is important to choose an appropriate bolting plan during development based on mining and geologic conditions if the entries will be used for the long-term. In both short-term and long-term entries, primary roof bolting is critical in building a strong and effective beam. But in long-term entries, supplementary bolting is necessary in certain cases to ensure roof stability can still be maintained even if a roof failure develops beyond the primary bolted horizon. This paper deals with roof bolting for long-term entries based on studying the progressive roof failure and roof falls under different geologic conditions. The paper presents bolting considerations in terms of bolt type, length, diameter and spacing as well as bolting strategy to minimize the risk of roof falls in long-term entries.

Jan 1, 2011

By W. C. Smith

Over the past several years, the Bureau of Mines has conducted studies on the performance of fully grouted resin bolts In underground mines. The effectiveness of resin-grouted bolts in maintaining a competent roof, even in weak rock, has been well documented in the literature. Recent Bureau studies have evaluated the affects of shortened grout columns on bolt behavior in a variety of rock types (1, 2, 3). The application of partial grout columns to primary roof support systems has been introduced as a viable alternative to fully grouted bolt systems in some mines. The point-anchored resin bolt and combination bolt represent such alternatives. While both systems usually employ some mechanical interlocking system, their primary difference lies in the length of resin column used. Point- anchor systems rely on an anchoring device that is a short length of resin column of 2 feet or leas. Combination bolts, on the other hand, often require 3 feat or more of resin column. Resin migration into voids and fractures intersecting the borebole wall is a major problem when installing fully grouted bolts in weak roof rock and can result in a reduced column length that provides reduced anchorage. The relationship between column length and anchorage integrity deserves closer study. The Denver Research Center of the Bureau of Mines has examined the load- carrying capabilities of resin-grouted bolts in weak strata. Pull tests were performed on about 900 resin-grouted, 4- foot-long bolts with column lengths ranging from 6 to 48 inches. The practical performances of 8 different column lengths were evaluated for 10 mines under in sit" conditions using data obtained from standard pull tests. In addition criteria are discussed, including engineering properties of the host rock for designing safer and more effective grouted bolt installations.

Jan 1, 1987

By Mohummad Akram

Statistical analysis of multi-seam mining case studies demonstrated that geologic structure and lithological type and sequencing were predominant factors in entry failures. Finite element analysis was used to evaluate the effects of stress field changes on entry instability under differing geologic conditions. Analysis showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Effects of external support on roof stability were examined. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research design, criteria were developed for roof stability evaluation under specified interactive loading conditions.

Jan 1, 1993

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By Hamid Maleki

During the last decade, a significant amount of research has been conducted by Energy West Mining Company, government agencies, academia, and consulting companies to develop predictive tools for assessing the stability of the Castlegate Sandstone, which is found approximately 250 m above multiple-scam coal reserves, Energy West Mining uses longwall mining techniques in its operations near Huntington, Utah, and these studies were initiated to satisfy requirements for maintaining the stability of the Castlegate Sandstone and resource recovery. In this study, the authors have used multiple-regression analysis techniques and a wealth of data collected over many years on geology, mining, and escarpment stability. The volume of failed rocks is used as the response variable after several other factors were considered, including measurement of surface deformation and frequency of mining-induced surface fractures. Geologic and geometric variables were obtained along 3.7 km of escarpment exposure at 130 study locations. Regression analysis of data for the first 29 study location, which had been fully' undermined, showed that surface topography played a critical rule in influencing escarpment stability. Preliminary regression analysis results from 70 study loca¬tions identified several other important geologic arid mining factors that influence be stability of the sandstone escarpment These are canyon slope, sandstone thickness, and mining influence ante.

Jan 1, 2000

By Winton J. Gale

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the leading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By John Bullock

Limestone and dolomite quarries were mapped to determine specific failure mechanisms for the various geologic and structural conditions. Algorithms for analyzing these mechanisms were incorporated into a software package together with ranges of physical properties such as joint shear strength, angle of internal friction, and cohesion for specified lithologic units. Reliability options using Monte Carlo sampling and sensitivity studies are included to evaluate alternative highwall designs. The package is designed to facilitate progressive stability evaluation of quarry highwalls as mining continues. This package includes an optimum design protocol that can be followed to avoid the potential of massive failure. The program was developed in conjunction with the quarry industry and is demonstrated using case studies.

Jan 1, 1993

By P. K. Kaiser

The purpose of deformation monitoring for the evaluation of the stability of underground openings is reviewed briefly and some results from laboratory tests of small tunnels are presented. The ground behaviour is described by comparison with the response of structural systems and illustrated by the data from the testing of small tunnels. It is concluded that the main objective of a deformation monitoring system for stability evaluation is to determine the actual process of deformation and instability in the area surrounding the opening. Only when this process has been established is it possible to use deformation measurements to design support systems or to improve construction or mining procedures. Present monitoring practice is not sufficiently orientated toward the aim of process description.

Jan 1, 1981

By John P. Dunford

U.S. Bureau of Mines researchers are investigating the ability of mine-wide monitoring systems already in place at many coal operations to provide a direct link between geotechnical instruments and the mine-wide monitoring console on the surface. This paper describes a number of field tests using instruments such as-string potentiometers to measure roof-to-floor closure and bed separation and pressure transducers to monitor pillar loading. The advantages of using existing systems include on-site data collection and analysis, real-time understanding of geological conditions, and long-term data recovery from areas that have become inaccessible to mine personnel. However, because data are generated constantly, large files develop very quickly. In many cases, the data are redundant, such as during times of reduced mining activity or in areas not yet in the vicinity of active mining. To reduce the volume of data, a software program was written that eliminates unnecessary readings and generates a more concise file that can be output to a mine-wide monitoring system, personal computer, or as hard copy.

Jan 1, 1993

By Thomas M. Barczak

Wood cribs are used extensively to stabilize mine openings by providing resistance to deflections of the immediate roof and floor and by supporting the weight of unstable rock masses. While the unit costs of these supports are relatively low, their extensive use results in significant costs to coal mining. The Bureau of Mines has developed a model that computes the load capacity of wood cribs as a function of the displacement of the crib structure induced by mine roof and floor convergence. This permits comparison of the loading characteristics of various crib constructions and enables systems to be designed with consideration of the load conditions imposed by the mine environment. The design method matches the stiffness, strength, and stability of the crib structure with expected rock mass behavior to determine a crib design and employment spacing that will provide the lowest cost support.

Jan 1, 1993