Search Documents

By Lynn B. Hales, Randy A. Ynchausti

Because of the high economic value associated with small improvements in the operating performance of mineral processing plants, innovations in instrumentation, stabilization and expert control systems have been an ever-present part of the landscape in plants throughout the world since the I 960s. Expert control systems are computer programs that continuously monitor plant conditions; contain "expert knowledge" concerning the process, equipment and operational knowledge; and make timely recommendations for new process set points or even directly change the process set points to achieve desired management goals. Early rudimentary expert control systems first appeared in the early 1970s. They have grown from small, experimental but ambitious projects in which single unit operations were controlled to plant-wide systems that include technologies used in the U.S. space shuttle program. Experiences and results of applying these systems throughout the world will be explained discussed and analyzed. Typical results will be outlined and the use of expert control in the future will be projected.

Jan 1, 2000

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, a1ternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pi1lar retreat practices have been successful1y imp1emented to mitigate coal mine bumps. Several techniques have evolved for room-and-pi1lar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U.S. coal mine industry.

Jan 1, 1992

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant. able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). [ ] The most recent development, however, is the use of H2O2 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). [ ] Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: Hydrogen peroxide must be diluted before it is added to the pulp. The dosage of H2O, must be properly regulated based on the oxygen level of the pulp. An important part of the continuous O, control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1990

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant, able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). CN- + H202 => OCN- + H2O The most recent development, however, is the use of H202 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O2, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). 2 Au + 4CN- + 1 /2 O2 + H2O => 2 [Au(CN)2]- + 2 OH Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: • In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. • In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: • Hydrogen peroxide must be diluted before it is added to the pulp. • The dosage of H2O2, must be properly regulated based on the oxygen level of the pulp. • An important part of the continuous 02-control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1989

By Allan E. Hall, Stephen G. Hardcastle, Lucien D. Nel, Jean-Paul Saindon

A description is given of the investigation conducted at Sherritt Gordon's Ruttan Operation in Manitoba during 1986. Gas and dust concentrations were measured in the exhaust air of the major working sections to assess the potential for recirculating exhaust air into the intake air in winter to reduce heating costs. The results indicate that there is excellent potential to significantly reduce winter heating costs by controlled recirculation of exhaust air. Gas and dust concentrations vary significantly during the working shifts but have consistent trends from shift to shift and day to day. The variations in gas concentrations have similar trends but no single gas could be reliably used to predict the variation of the other gas or the dust concentrations. Dilution and the other effects which reduce pollutant levels as the exhaust air returns to surface indicate that recirculation should take place as close to surface as possible, subject to the economic constraints of the airway construction required and the extra fan energy required for the longer recirculation path. Recommendations are made for the choice and positioning of air and dust monitoring sensors and the logic of a control system. Economic analysis of the results indicates that controlled recirculation is viable at an existing mine with a pay back period of approximately two years. Incorporation of a system into a new mine at the planning stage would significantly shorten the pay back period.

Jan 1, 1987

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By H. Mercado G., J. R. Parga T

Mexico continues to be one of the main producers of silver, lead and zinc; although this leadership is ending because of the use of obsolete technologies, which is reflected in low recoveries of these processes. The country therefore requires to develop on new technologies in the field of nonferrous metallurgy, particularly be'cause it is the second most important source of foreign exchange. A novel method, presented in this paper, demostrates that refractory gold and silver can be extracted from a complex sulphide concentrate by a one stage pressure oxidation in an alkaline cyanide solution, this is achieved by simultaneous liberation_ and solubilization of the precious metals. Both gold and silver extractions are greater than 97%. Factors affecting recovery efficiency, such as: pH, lixiviation time in the reactor, temperature, particle diameter, pressure, % of NaCN and pulp density, were investigated. A summary of actual plant operations is also be included.

Jan 1, 1993

By Paul D. Tomlingson

Editor's note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By G. R. Struble, J. R. Marks, A. B. Brown

The center of mining at the Homestake gold mine in Lead, SD, is moving deeper every year. As a result, it has become necessary to upgrade the ventilation system. This paper describes the first phase of a scheduled two-phase upgrade - installation of a 2.2-MW (3000-hp) centrifugal fan. The higher pressure fan is required to route larger airflows into the deeper production levels. Selection of the fan began by specifying the necessary operating point to provide these larger airflows. Special site work had to be done on the surface to accommodate the new fan structure as well as underground to reroute airflows.

Jan 1, 1987

By Stanley R. Riggs

Extensive phosphate resources occur within the Miocene Hawthorn and Pungo River Formations which have not been considered in the past since they were poorly known and were not available to conventional mining. These resources include 1) deep phosphates that occur below 75 meters of overburden within major sediment basins throughout the southeastern coastal plain, and 2) offshore phosphates that occur on the continental shelf and within the U.S. Exclusive Economic Zone (EEZ). The future potential of these two vast resources will be realized with development of new mining technologies such as hydraulic slurry mining and integrated with advanced technolgy already being utilized in the offshore petroleum industry.

Jan 1, 1986

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By Wayde Esplin

At the Barrick Goldstrike processing facilities in northeastern Nevada, sulfide ore is pressure-oxidized at a temperature of 440° F and 420 p.s.i. in six autoclave circuits. The low pH, high temperature, and abrasive characteristics of the oxidized slurry present many new and unique maintenance challenges. To meet these challenges, the Barrick Goldstrike autoclave department formed a reliability group in August 1998. One of this group's critical missions is to reduce both maintenance costs and unscheduled downtime through the application of predictive maintenance technologies and Reliability Centered Maintenance Analysis. This paper discusses some of the successes of the reliability program at the Barrick Goldstrike autoclave.

Jan 1, 2000

The new generation of computer environment provides mineral processing plants with convenient tools to store and retrieve or to analyze on-line process variable values as given along time by the various sensors installed in the plant. The paper describes the application of classical tools, such as time series analysis, to retrieve the hidden information contained is such data. The concepts used in single signal processing (autocorrelogram, power spectrum, ARIMA descriptors) and multi-signal processing (cross-correlogram, cross-spectrum) are briefly reviewed. Some examples are given to illustrate their application (sampling, data filtering, process behaviour prediction, process evaluation, data synchronisation). Examples are taken from mixing, flotation and leaching processes.

Jan 1, 1990

By James P. Dorian, James M. Otto

The value of exported nonenergy minerals from the less-developed countries has increased substantially between 1970 and 1985, but their market share relative to world exports has remained stagnant. Of the top twenty minerals exporters, only four are developing countries. Production capacity in the developing countries is shown to be less sensitive to demand downturns than capacity in the developed countries. Two approaches to the management of cyclical minerals demand are given using examples from India and Papua New Guinea. The authors conclude that pro¬tective policies implemented by developing nations have, barring a few exceptions, relatively little impact on the chronic nonfuel minerals oversupply problem.

Jan 1, 1989

By Ulrich Maidl

The use of EPB shields in the so-called mixed face conditions has set new demands to man and machine in EPB shield tunneling. EPB shields were initially conceived to drive in the pressurized closed mode in soft ground, whereas hard rock TBMs were designed to work in the unpressurized open mode. The present use of EPB shields in hard rock and mixed face conditions requires the combination of both technologies by finding best compromise solutions. This paper deals firstly with the geotechnical and mechanical interactions between machine and ground. Further on the critical points such as tool wear and tool replacement are exposed, together with a proposal of best solutions.

Jan 1, 2003

By P. Bottomley, M. Matthews

Maintaining an acceptable thermal environment in South African gold mines becomes increasingly difficult as mining progresses to greater depths where higher virgin rock temperatures are encountered. Current environmental practice offsets the resulting high heat loads by installing large refrigeration plants. However, with the continued escalation of refrigeration costs, it has become necessary to examine other methods for economically combatting the underground heat load. The Chamber of Mines Research Organization has recently been pursuing a programme to devise methods of reducing the flow of heat into underground workings at source. Although there are several sources of heat (such as machinery, men, and explosives), the most significant is that from the rock mass surrounding the workings (Bluhm et al., 1986a). The main thrust of the work has therefore been directed at predicting and devising methods of reducing this heat source. A great deal of theoretical work has been carried out on the prediction of underground heat flow. From a review of this work (Bluhm et al., 1986b) it became apparent that there are two major aspects which require attention, namely algorithms for predicting the heat flow around the advancing stope face, and a correlation of the theoretical work with accurate empirical data. In order to remedy this situation, new theoretical models have been developed (von Glehn and Bluhm, 1986), and heat flow measurements have been made in both a conventional stope (Bluhm et al, 1986a) and in a backfilled stope (Matthews u., 1987). A number of methods for reducing rock heat flow are being examined. These include the insulation of intake airways (Bottomley, 1985 ), backfilling with waste material of the worked out areas, and alternative approaches to the design of mining layouts, the mining method, and the choice of cooling strategy. This paper highlights the heat load reductions that can be achieved by backfilling the worked-out areas and by adopting concentrated mining. The first part of this paper summarizes the results of the measurements obtained in the conventional and backfilled stopes. The theoretical models are then described and comparisons are made with the measured values.

Jan 1, 1987

By William S. Gilmer

INTRODUCTION As man moved through the ages into the era of metals, he became increas¬ingly dependent on the extraction and beneficiation of various ore types. His progression has required more material, new sources, and inevitably, a need to extract the values from ores of much lower yield. Inherently welded to this need to extract has been the attendant requisite of power and water to carry out these tasks. With the richness of these deposits diminished, and the in¬crease of demand, mining has become so intimately tied with the needs of these auxiliary systems that the modern day milling operation can ill afford to ignore them. In the times of Agricola 16th century methods of milling required little thought for power or water consumption. Reduction was accomplished by hand¬sorting and hammer and grinding done with stamps and millstones. Medieval concentration was carried out by the "Jigging sieve" with agitation supplied by the sleeveless arm of the operator (The Mines Magazine,_ March 1933). Little consideration was likely given to the power source unless it became apparent that he had insufficient means to meet the demands of a dawn to dusk operation. Fuel for power production was also probably of little consequence unless sustained drought or warring neighbors burned the miners fields. Water was available from any adjacent stream with recycle, potable, tailings and mill consumption all going and coming from the same source. By the end of the 18th century and the early 19th century the requirements of larger throughputs and better re¬covery were forcing the miner to the need for greater sources of power and water. Arrastras, capable of accepting several hundred pounds of charge, con¬sisted of a clay bottom, a "liner of rocks harder than the substance to be crushed" and a revolving center post in which the ore was ground and amalga¬mated. Used in conjunction with a slucing system, this formed the primary recovery method of the time. Power was supplied by horse or oxen or, if terrain was amenable, by use of a horizontal or overshot water wheel. A typical system required 4.5 kw (6 hp) and needed to run in the vicinity of 15 rpm (Pre¬ston, 1895).

Jan 1, 1986

By W. C. Wheeler, G. Suranyi, J. F. Gentleman, J. Muller, R. Kusiak

INTRODUCTION In 1974 two of the present authors reported the results of a pilot study indicating an increase of lung cancer risk in Ontario uranium miners. (Muller, Wheeler, 1973, 1974) The study was based on data contained in a computerized Mining Master File maintained by the Ontario Workmen's Compensation Board that contained information on miners examined in Ontario who had either 60 months of dust exposure in mines or had signs of pneumoconiosis or tuberculosis. Including the above conditions the definition of uranium miners added the condition of one month or more of uranium mining experience in Ontario. This list of Ontario uranium miners contained 8,649 names. Following the results of this first pilot study, we embarked on creating a file of uranium miners containing information on men with one month or more of uranium mining experience in Ontario without any further conditions. This file was used by the Royal Commission on the Health and Safety of Workers in Mines in their study of risk in Ontario uranium miners. (Hewitt 1976) This file contained 15,094 names. In this report we give an outline and progress report on a study of Ontario miners that we are conducting at present. It was felt that the male population of Ontario is not necessarily an adequate control population for uranium miners. A preliminary examination of the work history of uranium miners indicated that the majority of them (about 90 percent) had other mining experience in addition to their exposure in uranium mines. We therefore considered it useful to evaluate the possible effects of non-uranium mining on risk, and for this reason decided to make the Uranium Miners Study part of a study dealing with the mortality of Ontario miners in general. Aims of the Study The aims of the Study include the evaluation of: 1) the risk of dying by cause in non-uranium miners as compared to the male population of Ontario and Northern Ontario. 2) any differences that might exist in the death experience of non-uranium miners by cause according to ore mined. 3) the effect of length of exposure in non-uranium mines on age-specific risk by cause. 4) the dose-response function for primary cancer of the trachea, bronchus and lung from exposure to radon and its short-lived daughters. 5) the possible effect of the mining environment on deaths from causes other than cancer of the trachea, bronchus and lung. The study will address itself to a number of other factors that might well affect the dose-response function. These include: a) factors in the mine environment - other than radon daughters - that might affect lung cancer mortality. b) the effect of non-uranium mining on lung cancer risk in uranium miners. c) the effect of age as well as age at time of exposure on lung cancer risk. d) questions of latency and the possible dependence of latency on age at time of exposure. e) smoking as an important factor in lung cancer risk. f) Histological type of cancer in relation to the various parameters of exposure and age. MATERIALS AND METHODS The Study is making use of existing computerized data files and has set up certain new files. These include the Mining Master File and the Model Development File. The Mining Master File This file is a computerized record of data on individual miners obtained at yearly miners' examinations that have been carried out since the mid 1920's. The conditions for inclusion in the Mining Master File have been indicated above. Information contained in the file includes: (1) Identifying information: a) Surname and given names b) Date and place of birth c) Miners Certificate Number d) Social Insurance Number if available. (2) Updated Employment data obtained at each miner's examination: a) Year of first dust exposure in Ontario b) Year of first dust exposure outside Ontario c) Number of months worked in mining d) Ores mined e) Mining areas and mines f) Occupations

Jan 1, 1981

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By Robert E. Murray

It's indeed a pleasure for me to speak to you today about the development and operation of large-scale surface coal mining projects in the western United States. It is an exciting story about American business working to solve a critical national problem -- the energy shortage -- through research, new technologies, financial innovation, and imaginative management. The North American Coal Corporation -- the second largest independent mining company and ninth largest United States coal producer -- is proud to be a part of this story. Our operations in North Dakota reflect the coal industry's Western activities. So, today, I would like to focus on our planned involvement in that state. I'll briefly survey why North American is developing large- scale surface mining in North Dakota, and I will outline the many problems associated with this coal development and how we are working to solve them. Finally, I will look at the financial and management techniques we are using to make it all work. In short, I'm going to present a case study of Western coal mining. Let's begin by looking at the reasons we are in North Dakota. The United States Bureau of Mines estimates that 44 per cent of the nation's total recoverable coal deposits underlie the three Northern Great Plains States of North Dakota, Montana, and Wyoming. We estimate that North Dakota alone has about 25 billion economically surface-mineable tons of coal with today's technology. North Dakota has the energy that could keep our factories running and our homes lighted In the years ahead.

Jan 1, 1975