Search Documents

By John A. Herbst, Per-Olaf Samskog, Jan Bjorkman, Yi Chang Lo

The study described here is concerned with the development of a model for the simulation and optimization of a rod milllpebble mill circuit. A series of laboratory tests was conducted to investigate the effect of critical operating variables. The pebble mill model structure used was a population balance type which accounta for impact breakage and fines production from pebble wear. Model parameterization and verification were performed using data obtained in batch tests and in a plant test campaign. The model developed was found to provide accurate predictions of plant-scale grinding. The prediction errors are less than 21 for the product size and 31 for the mill power required to achieve that product with a mill volume scale-up of 14,000 to 1. These results indicate that accurate extrapolations from laboratory batch data to plant scale performance are poaaible using the population balance model and scale-up prediction procedures for pebble mill circuits as well as ball mills. Preliminary indications are that the new model developed here will provide vital input for pebble mill optimization and process control as well as pebble mill design.

Jan 1, 1990

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By Robert L. Virta

An asbestos substitute is any material that replaces asbestos in a commercial product. There are many asbestos substitutes, each with its own unique physical and chemical properties. Substitutes can be inorganic or organic, fibrous or nonfibrous, and natural or synthetic. They also can be used as a direct substitute for asbestos or as a replacement product. Probably in no other field is the diversity of substitute materials so great. The concept of asbestos substitutes is not new. The first major effort to develop asbestos substitutes was undertaken by the federal government. The United States has always been dependent on foreign sources for strategic-grade asbestos, and during World War II, the government was concerned that these supplies would be cut off. Strategic-grade asbestos was critical in many electrical and thermal insulation applications (electrical insulation, battery plate separators, flame-proof boards, insulation for rocket components, etc.). A reliable supply of nonstrategic-grade asbestos also was required for general civilian and military applications, such as in brakes, clutches, and construction materials. The government not only initiated a major search for deposits containing strategic-grade asbestos, it also funded research on synthesizing asbestos in the laboratory and developing products that did not contain strategic- grade asbestos. These efforts, as well as those conducted by the private sector, generally were unsuccessful. In the late 1960s and early 1970s, a second major effort to develop asbestos substitutes began because the general public was concerned about the health threat posed by the release of asbestos fibers during the manufacture, use, repair, and disposal of asbestos-containing products. Strict regulations covering the mining and manufacturing sector already had been enacted because of the issue of occupational exposure. The issue then became environmental exposures. Environmental regulations were enacted, and through time they became more strict. The combination of increasingly strict environmental regulation, maturing of some asbestos markets, and liability issues prompted many manufacturers to discontinue asbestos product lines or search for asbestos substitutes. As a result, asbestos usage dramatically declined from the 1970s to the present (Table 1).

Jan 1, 1994

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By K. M. Stone, N. J. G. Masson, A. C. Woollett

The Jabali zinc deposit in Yemen contains at least 9.4 Mt (10.4 million st) of ore at a grade of 10.7% zinc, 2.2% lead and 77 g/t (2.2 opst) silver. The zinc occurs as smithsonite with minor hydrozincite. The Jabali ore does not produce a zinc concentrate of sufficient grade to be acceptable to a conventional zinc smelter, and it has been necessary to formulate a less-conventional development plan. This involves the construction of a mine and concentrator at Jabali and a metal production facility using a new flowsheet designed specifically for the treatment of oxide material at Yanbu, Saudi Arabia. To give the facility the necessary economies of scale, the Jabali concentrate will be supplemented by feed from other deposits, this may be either oxide or sulfide material. The paper outlines the geology and proposed mining and treatment operations at Jabali, presents the flowsheet for Yanbu and estimates preliminary costs for both operations.

Jan 1, 2003

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By Gordon S. Thomas

The problem of how best to exploit a reserve has vexed mine planners and design engineers since mining began. The cyclic nature of the mine design-scheduling problem, combined with the lack of good mathematical tools for tackling it, have ensured that it has been, and will continue to be, a major challenge for operations researchers working in mining. This paper reviews the current state of the art in pit optimisation and scheduling algorithms. Starting from the inception of the first block models in the late 1950's, it progresses through the developments and applications of the Moving Cone algorithm, the Lerchs Grossmann 3D Graph Theory algorithm and some of the heuristics, to the new artificial intelligence techniques that are being applied today. Along the way, it discusses the limitations of the various approaches and lays the foundations for the research that is currently being undertaken by CSIRO and others in the field of mine production scheduling and control.

Jan 1, 1996

By William E. Hole

The sand and gravel industry provides an enormous quantity of materials vital to the maintenance of low-cost construction. There has been little effort to conserve this valuable natural resource. In fact, existing regulations which affect sand and gravel operations act more to waste these materials than to conserve them. Another factor affecting the industry is new legislation requiring the reclamation of worked-out pits. Although such legislation creates many administrative headaches for a sand and gravel operator, there exists the possibility through such legislation of gaining some conservation measures that could be helpful to the industry.

Jan 1, 1974

By Robert F. Reeves, Stephens A. Avary

Introduction People, systems, methods, and organization make up maintenance productivity. Methods promote efficiency in operations, systems ensure consistency and continuity, and organization maintains direction and control. The common denominator in these techniques, though, is people. Management systems can be technically correct, but fail to work because management systems do not work by themselves - people make them work. Therefore, the foundation for mine maintenance productivity must begin with the people involved. Traditionally, the emphasis placed on mine maintenance, as opposed to production, is not proportional to the impact that maintenance has on a mining operation. The performance and productivity of mine maintenance substantially affects the operating costs, revenues, and profits of the mine. The mining industry has recently experienced a period of economic depression. While it has created financial problems in all segments of the industry, it has caused the industry to focus on the need for improved productivity. Mining companies that have made investments in productivity during this period will have a competitive edge during the recovery, and mine maintenance may be the best place to put that investment. Future lost production and maintenance cost problems can be avoided if mine management has the foresight to seize the opportunities that now exist. Background Technological improvements over the last 30 years have been dramatic in the industry. Before these changes, mining equipment was not very sophisticated. So maintenance needs were not very sophisticated. Maintenance people were not required to have any formal training in mechanical or electrical skills. At many mines there was no formal maintenance organization. The mechanic was a part of the section crew and received direction from the face boss. Mine maintenance was not a function, it was a task. Technological change in mining came about in response to an expanding economy and greater demand for mined products. The past 20 years brought about a change in the kind of individual needed to mine ore and coal, and an even greater change in the person needed to maintain equipment. Equipment went from mechanical and pneumatic to complicated electrical and hydraulic. Maintenance progressed from being a task to being a function. Types of Mechanics Mine maintenance workers can be grouped into three categories based on experience: mechanics with more than 20 years, five- to 10-years, and less then five years. These groupings have influenced mine maintenance productivity. The 20-plus mechanic has been the foundation of the maintenance force. He had no formal training and his skills were acquired on the job. As new equipment was introduced, he learned to repair it by trial and error. Not all of what he learned was correct. Personal initiative and conscientiousness are characteristics of this group. They have experienced the bad times and the good, and appreciate the opportunity to work. The five- to 10-year group worked with the older, more experienced mechanics to acquire maintenance skills. These mechanics came in during industry boom times, and many progressed quickly by being in the right place at the right time. Many in this group have difficulty with diagnostic trouble-shooting, and depend on changing out parts to identify problems. This group is generally more mobile and less apt to have a strong work ethic. Mechanics with about five years experience have vocational training, some formal education or basic skills training. Like the five- to 10-year group, these miners are mobile and tend to move readily to satisfy their changing needs. These two younger groups are less apt to feel any loyalty to the employer or obligation to be productive. Their attitudes and abilities reflect the influence of their general age groups, and has a definite impact on mining productivity. Past Requirements In the 1960s, the basic requirements for a maintenance supervisor was that he be a top mechanic, get along well with the men, and be a hustler and improviser. He learned the details of new equipment as repairs were needed. Oftentimes, this individual would be the only person on the property with the ability to read prints, use diagnostic testing equipment, and troubleshoot using an analytical approach. This approach to maintenance is sufficient when the equipment design is reasonably uncomplicated. Management Changes As technology progressed, organized labor gained strength, government regulation increased, and the job of supervising and managing people had to change. The environment has changed and

Jan 11, 1983

By V Leus, J. Kallioinen

The large size of the modern flotation cells and the high product flow rate from them has increased the importance of optimal flotation of all the particle sizes and of process control. By treating all the subprocesses of flotation separately a new family of flotation cells and a new concept of optimizing the flotation of coarse and fine particles in separate units but in the same row of flotation cells has been developed. The paper discusses the possibility to enhance coarse particle flotation by varying the froth residence time. A function has been developed between the residence time of the froth, air rate and the froth removal rate of coarse apatite particles. The response of apatite flotation to different control variables has been studied and modelled. The results show that the BPL assay response depends not only on the control variable used but also on the feed assay to the cell. There exists an feed assay dependent region within which the froth assay can be controlled by using the froth residence time as the control variable. These regions can be used to tune a rougher-multistep cleaner circuit to optimal.

Jan 1, 1993

By R. C. Beers, R. J. McKinley, R. D. Stewart

Preliminary test results at Occidental Research Corp.’s Irvine, CA, research facility indicate the viability of a new induced fluorescent sorting technique for preconcentration of limestone, coal, and oil shale. The patented “Oxylore”* process is a preconcentration stage that takes advantage of selective surface chemistry to label either ore or gangue particles with a fluorescent coating that can be detected by activation with ultraviolet light. The technology was originally developed by Ted Matthews (SME-AIME Fall Meeting, 1974, Preprint 74-B-328) and was acquired by Occidental in 1977. The firm has continued development of the process since its acquisition.

Jan 6, 1980

By Liu Cheng-si

Variable airway is controllable, which is an important discovery in ventilation research in recent years. For this reason, conventional calculating methods are no longer suitable to solve this problem. I used Mayeda-Seshu and Newton methods to solve the above problem before, they have been proved feasible. However, it is troublesome and difficult to apply to operation with a large amount of calculations. In this paper combination theory and simplified formula are used in determine all control plans and its parameters. This new method with less calculation is easy to understand and master, so it is more important in research and application.

Jan 1, 1997

By Z. T. Bieniawski

After many significant advances in mining, including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining strata control is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? Did you know that most design experts are often unaware of their own decision-making processes? This paper explores the methodology of creative engineering design as a new recognized discipline.

Jan 1, 1987

By P. Worley

Installation of UP& Is monitoring system was planned to be completed in three stages: Environmental Monitoring, ConveyorBelt Interface, and Power Distribution Interface. With Phases 1 and 2 completed and Phase 3 initiated, massive amounts of valuable information have been obtained. From this information, many benefits where recognized and the decision was made to expand the system. This provided monitoring and control capabilities in a variety of new applications from ventilation fan and pump interface to innovative installations such as ground control monitoring. All current uses as well as future plans for expansion and data manipulation will be discussed.

Jan 1, 1990

By J. L. Post, L. Borer

Small seams of fibrous tremolite and actinolite commonly occur in many California counties. A number of larger seams of this fibrous material were mined from 1882 until about 1955. The fibers from these mines were used for making acid filters, battery cases and fire-resistant paint. With increasing population, new residential areas are being developed in the foothill regions, leading to increased contact with seams of fibrous amphiboles. These forms of asbestos can be particularly dangerous to human health. Thus, it is necessary to determine the locations of these mines and adjacent veins and to identify the specific amphibole minerals present.

Jan 1, 2003

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By Pan Eimon

She was young, beautiful, intelligent, virgin. Her name was Barbara and she captured the attention of many men, especially those in dangerous occupations. Her rich and doting father was hopeful of making an advantageous marriage for his daughter. Instead, she defied him, became a Christian, and refused to marry. Traumatized, he killed her and was himself struck dead by lightning. That is not the plot of a new soap opera. It is the melodramatic story of a Turkish teenager who was martyred in the third century but lives still as patron saint of mining. The story begins with a 20th century fact. Santa Barbara is a figment of imagination - perhaps based on an early oriental folk heroine, embroidered by a seventh century storyteller, and reworked by a ninth century Greek martyrologist. The authoritative Lives of the Saints reports: "There is ... Considerable doubt about the existence of a virgin martyr called Barbara and it is quite certain that her legend is spurious. There is no mention of her in the earlier martyrologies, her legend is not older than the seventh century, and her cult did not spread until the ninth." The Catholic Dictionary adds that the Barbara story is probably "a pious legend." Widely revered Santa Barbara was one of the most widely venerated saints of the Middle Ages. She became the patron, not only to miners, but also to artillerymen, engineers, architects, builders, stonemasons, gravediggers, and sailors. Mines, mountains, churches, and places bear her name. Barbara's feast day, Dec. 4, appears on the most ancient holy day calendars. And a Barbara festival is still celebrated throughout central Europe, in Spain, and in mining areas of Latin America on that date. The Pacific coast channel, the city, and the mission of California are named for Santa Barbara. An expedition, sailing that coast under Viscaino in 1602, was saved from shipwreck on Dec. 4 after the sailors prayed for Barbara's intervention. Franciscans gave her name to the modern Franciscan Province of Santa Barbara, which embraces six western states and the Philippine Islands. Barbara is intimately entwined with mining. The origins of both saint and profession are lost in an-

Jan 11, 1985

By Paul F. Saxton

Introduction As the world economies continue to face an increased demand for natural resources to support growth in the established and developing world, the western mining industry has expanded its operations and funding of mineral developments into new and relatively unexplored regions of the world. Mining companies worldwide, in order to grow in a global economy, are now actively exploring and developing mineral resources in the emerging markets of South and Central America and most recently have expanded activities throughout Asia. South East Asia Resources (S.E.A. Resources) has recognized the vast resource potential offered by countries such as China, India and Indonesia, Asia's main driving forces of economic growth and has made a commitment to be actively involved in the area. These countries rich in mineral resources, represent some of the highly prospective and underexplored regions on earth. Their vast potential has been underestimated because of political reasons and overlooked as Central and South America still continue to be the focus of exploration for many mining companies. Most of these Asian countries have faced a prolonged period of political unrest and it has not been until recently that they have begun to enjoy a relatively stable political climate which has encouraged foreign investment, growth and economic development. These countries are in need of capital to develop their infrastructure and market economies. Their wealth in resources is one of the best methods to achieve their goals. Gold is usually one of the first targets to be extracted from developing economies. Equivalent-sized gold projects tend to cost less to develop and require less supporting infrastructure than base metals. These projects are easier to finance and, most important of all, tend to give a quicker return on investment than that offered by base metals. They also provide the economy with precious foreign exchange, international investment and the technology required to build the country. Following is a graph representing the global re-allocation of the total capital investment on the twenty largest gold projects now under construction with the total for those under construction in 1990.

Jan 1, 1996

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012