Search Documents

By Heflin. L.

The Washington Metropolitan Area Transit Authority, WMATA, has constructed over 92 revenue miles of rapid transit facilities including some 14 miles of rock tunnel and 12 miles of earth tunnel. The system map is shown in Figure 1. During construction it is not unusual for contractor to encounter ground conditions resulting in major problems and extra cost. Problems such as major rockfalls and a "stuck" boring machine in squeezing rock are not unusual. In recent years, faced with additional tunnel construction projects, the Authority has sought newer tunneling methods which might be less costly. One new method which has been tried is NATM, the New Austrian Tunnel¬ing Method. NATM, which is applicable to both soft ground, mixed face and rock tunneling, relies on miners and comparatively small machines to excavate in conventional ways, but it is unique in its methods of obtaining "stand-up" time at the excavated face and its method of using shotcrete as an initial lining, frequently with a drainage system to reduce hydro-static pressure on the final lining. Lower costs result from use of a cast-in-place concrete liner, and from a reduction in the number of work operations at the mine heading which provides better daily production. WMATA has recently completed three twin bore tunnels constructed by NATM technology. The first was the Wheaton Tunnel and Section, followed by the tail track tunnel to total some 4200 linear feet cut through jointed rock up to 270 feet below ground surface, and the last was in soft ground at Fort Totten. A

Jan 1, 1993

By Boris M. Vorobjev

The paper in question discusses a wide range of topics on the coal mining environment in general and on computerized coal mine environment systems in particular. The emphasis is being made on methodological aspects of coal mine environment with reference to computerized monitoring systems Classification of computerized coal mine environment monitoring system is suggested by the author with specific reference to coal mining operations. Coal quality control system at all levels (coal face to regional levels) is also discussed briefly hereunder, since coal quality is one of the major factor for environmental management. An integrated coal mining economic and environmental management super-system is presented in this paper Review Of the UN/DTCD, UNDP European Regional project "Computerized Coal Mining Systems" is presented here. Conceptualization of a new European Regional project on Coal Mining Environment and Economic Management is also a topic discussed in the paper.

Jan 1, 1992

By Robert L. Sandefur

Geostatistics of coal thickness and quality parameters for various coal seams in the San Juan Basin of New Mexico are reviewed. Interpretation of the histograms, variograms, and drifts of the data in the context of depositional environment and post-depositional geological history is discussed. A multivariate geostatistical technique for checking the accuracy of seam correlations is demonstrated.

Jan 1, 1982

By J. R. Sturgul

Computer simulation models of working mines can be a great benefit to mining engineers. Such models have been used in mine planning (how many trucks-shovels to have, when to add new equipment, etc.) and mine design (should a dispatch system be purchased, where is the optimum location, for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine. It can be easily changed to reflect a variety of situations. A major problem for the engineer is how to present the results of the simulation study. This has now been overcome by means of animation to present the results of the simulation. The main simulation languages in use for discrete system simulation are SLAM, SIMAN and GPSS/H. Each has animation with SLAMSYSTEM for SLAM, CINEMA for SIMAN and PROOF for GPSS/H. Animation with SLAM and CINEMA have been on the market for several years whereas PROOF is a relative newcomer and has features not found in other animation software. This discussion will be confined to PROOF. Some of the comments will apply to all simulation and animation software.

Jan 1, 1995

By I. WILKOMIRSKY, J. BECKER, F. Parada

The current processes that aim to purify molybdenite concentrates are not able to dissolve some copper compounds, hence limiting the processes. Typically, the copper content results are from 2 up to 4 weight percent in the last concentrate. Such values are still too high for the molybdenite concentrate to be further processed to molybdenum trioxide by roasting. In order to achieve lower levels of copper — but also avoid excessive molybdenite losses — a continuous sulfation-leaching process is investigated and applied successfully on a pilot scale. Additionally, a reactor prototype and its process parameters are proposed for a commercial plant.

Jan 1, 2023

By K. R. Wood, P. M. Blythe, J. A. Finch, M. L. Lavallee

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1991

By Michael McNinch, LaTasha R. Swanson, Jennica L. Bellanca, Justin Helton

As manufacturers and mine operators develop and implement proximity detection systems (PDSs), they need to be mindful of the systems’ compatibility with mineworkers’ tasks, and possible unintended consequences. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed mineworkers at mine sites that currently use or previously have used PDSs on mobile equipment, including shuttle cars, battery haulers and scoops. Mineworkers reported that mobile PDSs affect loading, tramming, section setup, maintenance and general work on the section. Mineworkers discussed the operational effects and increased burden, exposure and risk. Mineworkers also suggested that improved system task compatibility, training, logistics and PDS performance might help address these issues. Manufacturers and mine operators implementing this or similar technologies may also consider mitigating task incompatibilities up front, performing additional site-specific usability testing and restricting the use cases of the system to improve performance.

By Greg Beckstrom

Minnesota is a major mining state. This statement is not a dream or stretch goal but is a fact. As reported in a recent edition of Mining Engineering magazine, Minnesota ranks as the third largest state in terms revenues generated from nonfuels mineral production. The vibrancy of the mining sector in Minnesota can be attributed to several factors. The northeastern corner of the state is home to Minnesota?s iron range, one of North America?s largest deposits of iron ore. Iron ore from Minnesota is a strategic resource that has been [ ] instrumental to the nation?s development ? 90 percent of the iron used to build ships and planes during World War II came from Minnesota. Taconite pellets now produced from openpit mines on the iron range are shipped to steel mills worldwide. The growing appetite for steel in China and India has reignited once moribund mining operations throughout the iron range.

Jan 1, 2012

By Nasser Madani, SULTAN ABULKHAIR

The geological and geostatistical modeling of mineral deposits requires densely sampled drillholes that provide accurate and reliable hard data. Furthermore, quantifying orebody uncertainty through geostatistical simulation can allow mining engineers to assess long-term risk in mine planning. Nevertheless, ore deposits can sometimes lack dense drillhole information, reliable hard data with proper quality assurance/quality control (QA/QC), or sometimes both. This study is based on a coal mine located in the Republic of Kazakhstan, where an iron dataset is based on data from three newly drilled drillholes, and geological information comes from a massive collection of legacy drillhole data with no evidence of proper QA/QC. For this reason, a workflow was introduced to construct a representative training image from legacy data and stochastically model geological domains within these three drillholes using a multiple-point geostatistics technique. Once the geological model was obtained, a two-point geostatistics algorithm was applied to model the iron inside each geological domain. The direct sampling algorithm was chosen for modeling geological domains, and sequential Gaussian simulation for iron grade calculation. Both methods were extensively evaluated using different statistical tools and analyses.

Aug 1, 2022

By R. Milici

Current federal and State coal assessments estimate resources in the ground, resources available for mining, and economically recoverable resources. None of these assessments predict the amount of coal that may be produced from an assessed area in the near future (~20 years). Predictive assessments of coal production would be based on an understanding of the regional coal geology (coal systems), potential demand, and knowledge of the mining history of the region. The output of the predictive assessment would be a supply curve – a probability distribution of the amount of coal expected to be produced from current and new mines during the assessment period. I

Jan 1, 2004

By R. V. Ramani

This paper is based on the thesis that the demand for computer-oriented mining engineers will continue to sharply increase in coming years. It presents the philosophy behind the development of a mine systems engineering program at The Pennsylvania State University. The paper discusses the current status of mining engineering education and the problems encountered in integrating extensive computer background and education into a traditional mining engineering program. The paper analyzes the interrelated roles of research, graduate studies, and continuing education in developing a comprehensive program of study. It is hoped that this program philosophy will be useful to other institutions which are contemplating new programs and courses in emerging technologies.

Jan 1, 1982

By T. A. Toney, L. R. Fish, P. J. Bethell

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers and recirculation have been attempted with some success. This paper reports on a novel (patent applied for) approach to retreating spiral middlings in a heavymedia cyclone circuit.

Jan 1, 2000

By Tuncel M. Yegulalp

In this paper we revisit the well known "Ultimate Pit Limit Problem" and suggest an alternative approach for fast and efficient solution. We follow the approach originally proposed by Johnson and Barnes (1988), but utilize the "Excess Scaling Algorithm" in solving the equivalent maximum flow problem. This algorithm provides significant increases in speed and reduction in memory requirements over the well known Labeling Algorithm of Ford and Fulkerson (1956), enabling one to solve large problems with relatively small computers. We present results of a series: of benchmark tests using this approach against the well known Lerchs Grossman algorithm as well as a brief description of the new algorithm.

Jan 1, 1992

By Robert J. Wise, Mark Alspaugh

Underground longwall coal mines depend on conveyor haulage to transport large volumes of coal from the longwall face conveyor to the mine portal. In the last few years, the need for longer and larger longwall panel conveyors has become very significant. In order to keep conveyor equipment to a minimum and still transport higher tonnages over longer lengths, intermediate drive technology has been developed. The use of DC motors and controls in conjunction with load sharing techniques have a1 so proven effective. A case study of a new longwall panel conveyor at Utah Fuel's Skyline Mine incorporating these design techniques will be presented.

Jan 1, 1993

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

6.1 PRINCIPLES OF PLANNING GROUTING OPERATIONS FOR SHAFTS, DRIFTS AND TUNNELS The planning of integrated grouting of vertical, inclined or horizontal underground workings in saturated, fractured rock includes the following phases: 1. Planning for the collection and analysis of geological information concerning the characteristics of the struc¬tural deformation(s) that produced the details of the frac¬ture system being studied. 2. Planning for the acquisition of initial hydrogeological information produced by the flowmetric and hydrody¬namic investigations (described in Chapters 2 and 3). 3. Computing the initial engineering calculations of the ex¬pected or planned dimensions of the isolation curtains for each water-producing stratum (fracture zone) and the expected areal spreading pattern of the grout in each of these water-producing horizons. The selection of the lo¬cations, the initial optimal number of holes and the vol¬ume of grout needed to create each isolation curtain also are included in this phase. 4. The selection or development of a grout formula for the specific hydrogeological conditions that exist at the site. 5. Identification of a resource (deposit) required to produce the grouting clay. The planning of grouting operations must be supported by the acquisition of all necessary initial data, which in¬cludes: 1. The geographic location and administrative responsibil¬ity (ownership and regulatory constraints) of the mineral deposit and any peculiar features of the area where ex¬cavation of the underground workings is planned. The surface relief, the hydrographic network of the region, and the local climatic conditions must be evaluated prior to planning for buildings and waste discharges if any. 2. The economic status of the region, the available trans¬portation, the nature of the energy base, the water and heat supply sources, the location of construction mate¬rials suitable for making the grout all must be deter¬mined. 3. The geological and hydrogeological characterization of the work site must be accomplished. 4. The technical features of the shaft(s) and underground works must be characterized. 5. The organization's principal initial design plan features and the construction sequence of all buildings and struc¬tures must be developed. These must be correlated with the organization and schedule for excavating the under¬ground works. The technical characterization of a shaft or of other un¬derground workings must contain information about the purpose of the workings, the design depth, the planned excavation procedures along with cross-sections, and the parameters of the lining, if a lining is required. The geology of the section to be penetrated must include geological data obtained from existing exploration activities at the mineral deposit and conclusions about the shaft ex¬cavation conditions obtained from drilling technical moni¬toring holes and exploration drillholes. The interpreted stratigraphic regime, including the thickness, strike and dip of each stratum, must be shown in cross-section. The tec¬tonics, including all geologic structures, must be presented by cross-sections. The bedding orientations must be used to identify anticlines, synclines, monoclines and faults. The lithologic composition and the drillability of the rock com¬prising the section must be examined. The character of the rock's fracture pattern must be presented. Finally the per¬meability, porosity and storage characteristics of each aqui¬fer must be determined by in situ hydraulic property testing (injection tests or pumping tests, as described in Chapter 3). The fracture pattern of the indurated rock is presented in reports derived from geo-exploration borehole studies and from studies of outcrops on the surface and in all nearby underground workings. The extent of each fracture zone is mapped in three dimensions. The distribution of fracture apertures, the nature of the fractures according to each litho¬logic stratum, and the relationship of bedding planes to each fracture system are all determined. Acoustic logs, downhole cameras, caliper logs, oriented core, and any other appro¬priate geophysical tools available are used to construct the data base for this purpose. The hydrogeological characterization of the geologic section to be penetrated by the workings is based on the analysis of hydrogeological data collected during the drill¬ing and testing of technical monitoring holes and from in¬formation on ground water inflow collected during the ex¬cavation of nearby underground workings, if such workings exist. The hydrogeologic characterization must contain the following information: 1. The identification of all aquifers, their thicknesses and their locations in the section, 2. The distribution of hydrostatic head in the ground water in three dimensions, 3. The coefficient of saturated hydraulic conductivity (per¬ meability) of each aquifer, 4. The porosity and storativity of each aquifer, and 5. The projected rate of water inflow into the shaft, drift or tunnel for each aquifer prior to grouting. This step is used to identify the zones to be grouted.

Jan 1, 1993

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By George W. Luxbacher

The inclusion of a new term "planned subsidence" in the Surface Mining and Reclamation Act of 1977 has lead the U.S. coal mining industry into a new aspect of engineering: subsidence planning. Subsidence planning has necessitated the integration of geotechnical, civil, and mining engineering disciplines. Although much of the foundation and application work has been completed, subsidence planning is still a developing area. This paper discusses the application of subsidence planning in several brief case studies (a high voltage transmission tower, a sewage treatment plant, and a slurry impoundment), emphasizing the risk assessment aspects necessary to account for some of the uncertainties that may exist.

Jan 1, 1986

By R. D. Williams

"In a very real sense, Butte, MT is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site.One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot smelter operated from 1881 to 1910, moving Upper Silver Bow Creek to the south and depositing approximately 283,000 m3 (370,000 cu yd) of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 171,000 m3 (224,000 cu yd) of contaminated material. As part of the Superfund remedy, the U.S. Environmental Protection Agency (EPA) proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place, which set the stage for a series of studies that continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. History of the Parrott Mine and tailingsPlacer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery led to a stampede of placer and lode claims. One of the first lode claims located was the Parrot lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow, and it was not until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine.The Parrott Mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the district’s rich copper ore. In 1885, the employees of the Parrot smelter bought the Butte Reduction Works, another smelter. In 1885, dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Fig. 1).By 1890, the various smelters in Butte rendered Butte’s air quality as suffocating (Fig. 2). An 1889 funeral procession was rumored to have gotten lost in the thick smelter smoke and somehow ended up at the Centennial Brewery. A city ordinance was passed late in 1890 in an attempt to control smoke. The Parrot smelter employed approximately 500 men by 1890. Through the 1890s, the tailings produced grew from approximately 91 t/d (100 stpd) to more than 181 t/d (200 stpd). Copper values in the tailings were initially as high as 4 percent, but as the processing improved that was reduced to 1.5 percent."

Apr 1, 2019

By LUIS ALBERTO TORRES-CRUZ

The Plewes method is relatively well known among geotechnical engineers interested in assessing the liquefaction potential of soil deposits. Furthermore, it was one of the four methods considered in the post-failure investigation report of the Feijao Dam I, also known as the Brumadinho Dam, in Brazil. The inclusion of the method in that report is likely to increase its visibility among geotechnical practitioners tasked with assessing the liquefaction potential of tailings. While the authors of the method duly presented it as a screening method, more recent technical literature contains conflicting views on its reliability. Considering the popularity of the method and that the safety record of tailings dams is a cause of great concern, this study assessed the uncertainty of results from the Plewes method. The study concludes that, even under optimistic assumptions, the results of the method are too uncertain for detailed characterization of tailings deposits.

By B. E. Zeigler

This bi-product from a nickel smelter has been manufactured over the last 30 years for the abrasive and roofing industries. This paper discusses a new development for this material a foundry aggregate used for molding sand in both ferrous and non ferrous casting industries. Test data, marketing strategies, manufacturing, and case studies will be presented from the first concept, to current production, marketing and the end use of this product.

Jan 1, 1999