Search Documents

By L. Yuan, J. Soles, W. Tang, R. Thomas

Lithium-ion battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12V, 24V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicated that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Feb 1, 2023

By William E. Cobb

15.1 INTRODUCTION The mine development process, as discussed in Chapter 2, is a series of data gathering and analysis steps. As the mine development process proceeds, information about the geology, mineability, and metallurgy of a particular deposit is continually generated, along with environmental information regarding project permitting status. As data are obtained, checkpoint evaluations are typically conducted to determine the economic viability of the particular deposit. Although the project evaluation process was discussed at length in Chapter 2, a brief review of the process is presented here to "set the stage" for the discussion on economic analysis of heap leach projects. Figure 15.1 (MacKenzie, 1980) presents an overview of the sequential process of mine development. Once the deposit is discovered or acquired, an initial delineation program can be undertaken to expand the project's geologic, mining, and metallurgical data base. At the end of this initial program, the direction of the project is evaluated. The company can either abandon the project, postpone it, develop and mine it, or gather additional data in hopes of improving the project's economic viability. If the company continues gathering data, then another decision point and evaluation will be required. This process may continue until the company either decides to postpone the project or develop and mine it. A project may be postponed indefinitely, typically in hopes of improved metals prices. Certain holding costs, such as land or royalty payments, may be associated with postponement. In general, once a company goes through two evaluations, the project is less likely to be abandoned. For this discussion, it is assumed that the company will undertake initial, second, and third delineation programs to gather sufficient geologic, mining, metallurgical , and environmental data to justify a positive production decision from the second or third economic evaluation. The objectives of the first delineation program will be to confirm and expand upon the available information about the deposit. During the second delineation program, development funds should be directed toward identifying the critical project items (i .e., ore reserves, mineralogy, mineable grade, metallurgical recovery, etc.) that must be resolved before making the production decision. This second economic evaluation can be used to determine which metallurgical concept will be applied to the project: heap leach or a traditional agitation-type leach plant. If the proper work has solved key project concerns in the second program, a production decision may be made from that evaluation.

Jan 1, 1988

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By Paul E. Epstein

Despite the controversies that have surrounded asbestos over the past 20 to 30 years, no knowledgeable authority has doubted the usefulness of this material. Were it not for the health risks associated with the manufacture and use of asbestos products, its physical and chemical characteristics would continue to be hailed as an undeniable boon to mankind. However, it has become clear over the past 30 years that like other major contributors to our modern industrialized society, asbestos must be handled responsibly and with the full understanding that lack of care can lead to injury, suffering and death. In this sense, asbestos shares characteristics with nuclear power, pesticides and even motor vehicle usage. It is unlikely that modern society would be willing to walk away from the benefits bestowed by any of these valuable resources. Rather, the appropriate response to the identification of danger is to define the type of risk, quantify its incidence, search for methods of decreasing the risk and implement programs to achieve the goal of minimization of risk. We should recognize at the outset that the risk cannot be diminished to zero without elimination of the material entirely from our midst. The concept of acceptable risk is a complex issue involving medical, legal, financial, moral and even psychological factors that defy precise quantification. In essence, the major danger produced by exposure to asbestos is its potential effects on the respiratory system. Despite the fact that asbestos workers have constant skin contact with the material and porbably swallow it in the course of their activities, inhalation of the fibers is recognized as the major health risk associated with its use. Aerosols of asbestos are inhaled not only by miners, millers and fabricators but also by urban dwellers who have no direct occupational contact with the material. This occurs because asbestos has been applied to our buildings and has been used in a wide variety of products that touch our daily lives. While it is estimated that three to four million people in the United States have been occupationally exposed to asbestos, the number who have been non-occupationally exposed is many times that number.

Jan 1, 1984

By P. I. James, M. R. Baker

This paper examines new copper production from waste-grade ore using Blue Planet Strategies’ DEMET™ (Dynamic Electrode Mining Effluent Treatment) technology, which aims to bridge the practical weak pregnant leach solution (PLS) processing gap in heap leach-solvent extraction/electrowinning (SX/EW) operations by electrochemically removing metals from weak streams and generating product streams strengthened in target metals in a functional analog to SX. Weak PLS treatment was studied and used to estimate the economic and production impacts for a representative hypothetical brownfield copper heap leaching and DEMET-augmented SX/ EW operation to utilize "waste ore." Copper removal at 86% plating efficiency to below 0.1 g/L copper with power consumption of 0.55 kWh/lb copper and product strengths of over 10 g/L copper are presented. Modeling yielded approximately $2/lb total copper production and = $1/lb treatment costs with an immediate operation gross margin increase of 12% for the augmented brownfield. Potential mine life extension with an average 38% gross margin on "waste ore" augmented production at copper values of $3.25/lb was also indicated.

Jan 1, 2014

By Anibal Gajardo

Because of the Chilean Ministry of Mining's interest in the development of industrial minerals, the Chilean Geological and Mining Service (Servicio Nacional de Geología y Minería, SERNAGEOMIN) has carried out a research program during the last two years to identify projects that represent interesting investment opportunities for small- to medium-scale operations in Chile. Most important of these projects are: (1) Quebrada Lluta aluminum sulphate, for drinking- and industrial-water treatment, with a potential domestic and foreign mar- ket of almost 43,000 tonnes per year and investments of about US$1.8 million; (2) Quebrada Lluta-Quebrada Cardones pumice, for abrasives, filters, fillers, and light- weight aggregates, with a potential market of about 30,000 tonnes per year, and in- vestments of US$2.0 million; (3) El Maule dolomite, for soil conditioner and iron smelting, with a total potential domestic market of some 60,000 tonnes per year, and estimated investments of US$2.0 million; (4) Las Escaleras bentonite, for animal feed, pelletising, and oil absorbents, with a potential market of almost 6,000 tonnes per year, and investments of about US$2.4 million; (5) Laraquete-Carampangue andalucite, for alumina refractories, with a future total domestic and foreign demand of about 15,000 tonnes per year, and estimated investments of US$2-2.5 million; (6) Rio Lía garnet, for fillers and sand-blasting abrasives, whose domestic market represents 10,000 tonnes per year, with investments of US$2.3 million; and (7) Munilque pumice, for building bricks and panels, with a potential domestic market of 250,000 tonnes per year, and investments of US$1.4 million. The development of these projects will represent an important increase and a significant diversification in Chilean industrial-minerals production.

Jan 1, 1999

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

By Claes G. Björk

Over the past decade mined unlined rock cavern storage for crude oil and refined products has become economically more attractive. This trend is likely to continue, primarily due to advances in excavation methods, rising steel costs for above ground tanks and larger capacity requirements. The construction experience related in this paper comprises the excavation of more than 80 storage facilities (total capacity 90 million bbl) for crude and refined products ranging from propane to heavy fuel oil. This paper also deals with the experience gained as well as the problems derived from the utilization of these oil storage facilities.

Jan 1, 1981

By Prasad Kummarapurugu, Maija Teijonsalo, Sirkka-Liisa Jamsa-Jounela

There has been a significant progress in the use of mathematical modeling and simulation in the minerals industry in the last decade. Process models have moved from academic world to important industrial tools. This paper reviews the status of mineral processing simulators and recent progress in simulator development and applications is discussed. The simulation for process design and optimisation is now an established technique, as evidenced by its increasing use of practising engineers through commercially available simulator software. The paper presents a systematic approach to the process study procedure for the control system development, clarified by practical case examples calculated by SimCon - a novel steady-state simulator for mineral processes. Examples of the application of SimCon in drawing flowsheets, calculating mass balances and making simulations for grinding and flotation processes are presented. At the end of the paper, the state-of-the-art and the future of computer-aided pro- cess study at mineral processing plants is discussed. Keywords: Simulators, modelling, object oriented programming, computer aided control system design

Jan 1, 1996

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

By H. Wilcox, M. Prichard, Y. P. Chugh

Environmental considerations related to the disposal of coal combustion byproducts (CCBs) and the impacts of deforestation associated with the harvesting of timber for utilization as roof supports in mines should become more severe in the future, as landfill space and suitable timber reserves become more scarce. To help address these concerns, lightweight artificial supports, such as post and crib elements, that use large percentages of coal combustion byproducts as aggregate have been developed for use in underground mines. These structural products show equal or better engineering characteristics than timber, and they have the potential to replace timber support in underground mines. CCB-based ultralight structural material (ULSM) has also been developed and commercialized for use in the construction of ventilation stoppings in underground mines. The bulk densities of these blocks range from 0.40 to 0.64 g/cm3 (25 to 40 lb per cu ft) with more than 75% CCBs. Efforts are also given to develop and demonstrate large volume CCB-based subgrade improvement technique for road construction. Soil treated with SIUC fluidized-bed combustion (FBC) fly ash developed an immediate bearing value exceeding 25% with a swelling strain of less than I %, which is greater than untreated soils, and met Illinois Department of Transportation (IDOT) standard specifications. In this paper, development procedures, engineering characteristics and beneficial uses of CCB-based structural products are given.

Jan 1, 2002

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Richard E. Gertsch

The recent upswing in mining coincided with increased environmental concern. These trends have significantly increased regulation, but have not always provided sound environmental protection. Throughout, mining has remained passive, reacting to initiatives from outside. The high road to environmental protection must be an active strategy. The mining industry must take the lead and develop an environmental program effective in price and protection. It must involve all levels of mining. The mining industry should be the real environmental activist. We have the most to gain by sound environmental protection and the most to lose if the environment decays.

Jan 1, 1991

By H. J. Ilgner

Previous applications for using waste rock for backfilling in South African gold mines were reviewed and it was found that in many cases the mechanical equipment selected and the design philosophy applied did not meet the requirements. A more simplified system configuration is proposed, which allows the equipment to be relocated as mining progresses. Innovative high-intensity grinding and dense-phase pumping technology are proposed to provide a low-porosity backfill with a particle top size of 5 mm to 8 mm. According to recent rock mechanics modeling work, this comminuted waste backfill material can provide a good compromise between underground support characteristics and reliable hydraulic transportation behavior.

Jan 1, 2001

By Ching L. Wu, Bolek Chytrowski, Peter Frobenius, Dale Roberts

During the past few years, the first stage of the Waste Isolation Pilot Plant, (WIPP) which consists of an exploratory shaft, a ventilation shaft, shaft stations, access drifts and test rooms, has been under construction. Construction of the first stage is scheduled to be completed in the summer of 1983. The U.S. Department of Energy (DOE) is constructing the WIPP facility to demonstrate the feasibility of disposing of defense-related nuclear waste in the bedded salt deposits of the Delaware Basin near Carlsbad, N.M. The project promises to be a proving ground for underground nuclear waste storage facility design and construction. The completed underground plant will extend over an area of 647,500 m2 (160 acres), and 1,360,500 metric tons (1,500,000 tons) of salt will be excavated. The first stage of the project, the Site and Preliminary Design Validation (SPDV) Program, provides for full-scale construction of the major components of the underground facility. Shaft construction and underground development are described. Rock bolt installation is performed as required for roof control. Geotechnical instrumentation is installed to monitor the behavior of underground openings. Direct observation of the constructed shafts, shaft stations, and underground openings is expected to confirm the adequacy of the underground design and allow full-scale construction of the first U.S. underground nuclear waste storage facility to proceed.

Jan 1, 1983

By J. A. Brierley, R. Y. Wan

Newmont Gold has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for the pretreatment of low-grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the preg-robbing characteristics of the carbonaceous matter in the ores. Therefore, an alternative heapleach process using ammonium thiosulfate was developed to extract gold from these preg-robbing biooxidized ores. The ammonium thiosulfate leach process was successfully applied in both laboratory and pilot plant tests. Satisfactory test results were achieved, encouraging the continuation of process development.

Jan 1, 1998

By Zhongxue Li, Shuang Gao, Zhixin Zhen, Yiqing Zhao, Xuan Qin

If not well-managed, a mine-tailings facility may become a major source of risks, endangering the community and environment, and damaging the reputation of the minerals industry regarding sustainability. Identifying, characterizing, and mitigating the hazards and risks associated with tailings facilities have been critical to the maintenance of community-safe and environmentally sound mine-tailings facilities. Herein, a complex network model for characterizing the hazards and risks associated with the lifecycle of tailings facilities is presented. In this approach, the hazards are modeled as vertices of the complex network, and the interactions among the hazards are modeled as edges of the complex network. The complex network for modeling the hazard and risk spreading of mine-tailings impoundments is analyzed and characterized by using network metrics such as the network density, geometrical characteristics, characteristic path length, network efficiency, and clustering coefficient. The degree distribution of the network obeys a power-law distribution, indicating that the network for characterizing the risk spreading associated with a tailings facility is scale-free. According to the results of calculations and existing research results, the network is ultrasmall-world. By analyzing the change of the global network efficiency under four kinds of different methods to remove network nodes and edges, network nodes with higher between centrality (BC) are identified as critical. The removal of those critical nodes helps mitigate risks associated with a tailings facility and reveals the vulnerabilities to BC attacks.

Jan 1, 2017

By Y. J. Wang

This paper describes a procedure for solving the generalized system of n network equations in n unknowns considering the following ventilation variables and parameters: (a) air quantities, (b) pressure losses or gains caused by the control devices (i.e., fans or regulators), (c) resistance factors, (d) natural ventilation pressure, and (e) fan pressures (as a function of air quantities). The air quantities and pressure losses for all branches in the network are grouped into dependent and independent variables. The branches with an independent quantity are contained in a chord set, and the branches with a dependent pressure loss are contained in a chord set. In addition to the problem formulation, the solution procedure, applying the Newton method, is discussed and illustrated with a numerical example.

Jan 1, 1989

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines examined bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U. S. coal mines. Results indicate that restricting airflow into mined-out areas (bleederless ventilation) is recognized worldwide as a spontaneous combustion control measure. However, ventilation practices commonly used to limit airflow to mined-out areas are not easily applicable to United States mining conditions, systems, experience and regulations. The types of bleederless ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems are discussed. Primary design considerations for bleederless ventilation consist of the interaction of ventilation practices, methane drainage, ground control, seal construction and mine monitoring. Technological improvements needed for U.S. application of bleededess ventilation are also discussed.

Jan 1, 1995

A number of factors have resulted in the widespread use of computer simulation as a day to day tool in the mineral processing industry, as is the case in most engineering disciplines. A number of simulation packages, both steady-state and dynamic are now available commercially. The developers of such software face an enormous challenge in maintaining and improving the packages due to the complexity inherent in such systems. This problem known as the software crisis faces all developers of complex software. Object-oriented (OOP) and design is a methodology which has been developed to try and minimise this problem. The use of the OOP paradigm in the devlopment of simulation software for mineral processing systems is explored in this paper and it is found that OOP techniques have major benefits for the design and development of such software.

Jan 1, 1992