Search Documents

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two stage conditioning process was attributed to the amount as well as changes in the nature of the adsorbed collector species upon reconditioning. In this paper, bench scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1988

By R. A. Pimentel

Many longwall operators experience difficulty complying with the federal regulation limiting average dust exposure. Others are currently in compliance, but the dust exposure limit keeps then from increasing their production. Spray water is a major means of dust control. Excess water can cause problems in the transportation system and the cleaning plant, and reduces the Btu value of the run of mine coal. Thus, the dust exposure reduction per unit of water sprayed must be maximized. This paper discusses underground tests recently completed as part of a Bureau of Mines research program to determine the effects of variations in spray water flow rate, pressure, proportioning and spray orientation on longwall shearers.

Jan 1, 1984

By Carl-Eric Dr. Nilsson

Energy cost for mine ventilation in Sweden is high, especially during winter time when air must be heated. This paper presents the result from a project entitled ventilation-as-required. The term ventilation-as-required means that the required volume of fresh air should be distributed only to such areas, where mining work is going on and to be reduced to a minimum in the rest of the mine. Ventilation-as-required is a monitoring system that controls the operation and capacity of the fans and measure the air pollutant gases, i.e. carbon monoxide, nitrogen and sulphur dioxide at strategic points. It is an active system that responds when equipment is under operation. MITU proposed in 1991 a project to develop a ventiation-as¬required system and such components as transmitters and receivers for the communication between the equipment and the fans. The mining companies, Boliden Mineral AB, LKAB, Outokumpu and Ammeberg Mining Corporation joined the project and have financed a joint research and development programme supported with a grant from the Swedish Government through NUTEK. MITU proposed a second project in 1992 to the mining companies to develop an improved "intelligent" fan for scope ventilation. Boliden Mineral and LKAB joined the project and have financed a joint research and development project supported by the Swedish Government through NUTEK. The Government even made a commitment to support the investment of the first 50 fans ordered with a grant of 25% of the investment cost. The result from projects show that the target set up in the plans is more than achieved, with an energy reduction that exceeds 30% compared to previous consumption. No environmental influence due to reduced ventilation is observed in the stope when work is under progress. Dilution of exhaust gases from diesel fuel decreased from 6.000 m3/L consumed diesel fuels to 3,600 m3/L. The automatic data processing and sensor system is even increasing the security of the work so that it can be done under safer environmental conditions.

Jan 1, 1995

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

By Steven J. Schatzel, Kayode M. Ajayi, Bo H. Kim, Zoheir Khademian, Gabriel S. Esterhuizen

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a discrete fracture network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A fracture flow code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.006 m3/ s, significantly lower than the average inflow of 0.22 m3/ s for a shallow-cover mine (145-m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk.

Jun 19, 2022

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By B. Salopek, D. Rajkovic, D. Rumenjak

Among other types of sustainability indicators, linguistic variables have been proposed. During the past few years considerable effort for using the fuzzy logic and linguistic variables (LVs) in environmental decision-making for the mineral industry has been made. The linguistic variables defined could, among others properties, describe the property of acceptability for environment for various environmental indicators. Some proposals for construction of such variables are based on administrative decisions from environmental impact assessment procedures for mining, which provide information for acceptability of quality kind for environment (e.g. obtained from public participation, experts, environmental administration). The measures of evidence for construction have to be based on sets (not only on the members of sets). The administrative decisions with their statements and explanations could be considered as such sets. The measures of evidence appropriate are plausibility and belief measures. Using the more elaborated methods from the theory of evidence, the better estimation of those measures could be achieved. The methods of constructing the linguistic variables, previously suggested and based on obtained measures, are also discussed.

Jan 1, 2011

By William I. Weisman

The annual consumption of fluorspar in the United States, in the last 10 years has doubled. In 1971, when 1,344,742 tons were consumed, almost 45 percent of this amount was used in the production of steel and nearly 50 percent was consumed in the manufacture of hydrofluoric acid. Of the hydrofluoric acid produced, about one-third was used in the manufacture of aluminum electrolytes for production of primary aluminum metal and the balance was consumed in the manufacture of a variety of fluorocarbons and other chemicals. A small amount of fluorspar, constituting less than five percent of total consumption, was used in the foundry industry, and in the manufacture of glass, enamel, cement and other products. It is apparent that a continuing supply of fluorspar will be required to meet the demands for these vital metals and chemicals in our expanding industrial society. Domestic fluorspar production meets only approximately 20 percent of our needs. Hence, it is essential that the United States maintain a healthy domestic fluorspar industry in order to have adequate domestic reserves available at times of emergency and to protect this country from becoming solely dependent on foreign sources for this strategic commodity.

Jan 1, 1973

By Javad Sattarvand, Frimpong Kwaku Asare

The safe evacuation of miners during an emergency in the shortest amount of time is one of the most essential features of a mining operation. Despite advancements in mine evacuation research, the usage of mine vehicles during evacuation has not been considered. The majority of recent studies have been done on miners’ evacuation on foot. Mathematical formulations including Minimum Cost Network Flow (MCNF) models, Dijkstra's algorithm, Floyd-Warshall algorithm, and Ant Colony Optimization models have been used to solve mine evacuation problems. These models, which concentrate on determining the shortest escape routes during the evacuation, have been found to be computationally expensive and may not offer the best solutions in some cases. The goal of this paper is to incorporate light vehicles in the evacuation process using a mixed-integer programming approach. The methodology aims to minimize the total time required to evacuate the mine, ensuring minimal exposure of the miners to the adverse conditions that triggered the evacuation.

Jun 25, 2023

By Sidney L. Hansen

This report was written because of concerns of the possible error involved when stopping leakage is incorrectly assumed to be turbulent. It is common practice to use turbulent flow to characterize each airway branch for computer models of mine ventilation circuits. This report addresses computer methods to accurately model air-leakage paths. A graphical method is described for deriving the equations of leakage through stoppings. The significance of modeling leakage according to the proper flow regime (turbulent or laminar) is demonstrated by the following method. A hypothetical mine was developed to represent present-day conditions. The stoppings of the mine were chosen to leak according to laminar flow properties. The mine was represented by constructing two base models. One base model used turbulent leakage equations for each stopping, while allowing the corresponding resistances to vary. The other base model used the correct laminar leakage equations and held corresponding resistances constant. The mine circuit was then expanded to demonstrate future development. The expanded portion was designed with stoppings that were identical to those in the base mine. The mine in the future state was represented by two projection models. Each projection model was an extended version of its associated base model; one used turbulent leakage equations and one used laminar leakage equations for stoppings. The laminar projection was theoretically correct and is used as a basis for comparison of differences in airflow quantities. Rather than modeling every leakage path for stoppings, a more practical approach is also discussed. A good level of accuracy is maintained by combining leakage paths if the proper flow equations are used. This method was used on the hypothetical mine projection and the flows were very similar to the theoretical values.

Jan 1, 1989

By K. Cothern, S. Novack, D. A. Johnson, R. Borden, S. Pavlou

A procedure is presented for ranking hazardous waste sites for remedial decisions, and an example with application to mining waste sites is discussed. Typical contaminant concentrations are calculated from field data. Exposure indices that compare these measured concentrations with allowable limits are then computed. The limits are selected to protect both the health of humans (for both carcinogen and noncarcinogen effects) and the health of key organisms in the ecological food web. The additive exposure index for a site, defined as the sum of all contaminant-specific exposure indices, is then used in ranking the sites and assigning each a priority for remedial action. One key source of uncertainty in the process is the estimation of a typical site concentration from data that include values reported as "below certified reporting limit" (BCRL). This uncertainty is compounded in the additive exposure index and therefore may have a substantial effect on the assignment of remediation priority. A general approach is presented for incorporating consideration of BCRL data into uncertainty evaluation when assigning remediation priority designators to hazardous waste sites.

Jan 1, 1992

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By S. D. Thompson, L. Adler

Several researchers in the last 20 years have developed computer simulation models for designing coal mine belt systems. A careful review of these reveals that each omitted or oversimplified important factors, especially in belt loading. To remedy this, the coal mine belt capacity simulator (CMBCS) was developed to include various types of probability distributions, delays, and longwall and continuous haulage. CMBCS is computer coded in FORTRAN and employs the Monte Carlo simulation technique. Basically, the model simulates the loading and corresponding flow of coal through a belt system. By recording spillage and belt stoppage statistics for the simulated flow, belt and surge bin capacities can be evaluated. A complete user's guide is available. The modeling and verification of CMBCS are briefly described, and its major advantages and disadvantages are explored.

Jan 1, 1987

By Y. J. Wang

The concept of subsystem characteristic curves for multiple-fan ventilation networks is presented through the construction of characteristic curves for two-fan, series-parallel networks. By considering fans as the individual network branches, the multiple-fan network is viewed as consisting of two components: any one fan branch, which is called the reference fan branch, and its associated subsystem. Thus, F subsystems can be designated for the network with F fan branches. Each subsystem contains one or more fan branches. The subsystem characteristic curve is the pressure-vs.-quantity curve of the subsystem. As illustrated in the example networks, the subsystem characteristic curve is not a strictly increasing curve and does not pass through the origin. The intersection of the characteristic curves for the subsystem and the reference fan branch represents an operating point. Multiple intersections therefore represent multiple operating points.

Jan 1, 1994

By Robert S. Setren, Jeffrey L. Ambs

The disposable diesel exhaust filter (DDEF) system developed by the U.S. Bureau of Mines and Industry cooperators for heavy-duty permissible, diesel-powered haulage vehicles, effectively reduces in-mine diesel particulate matter concentrations up to 95%. However, there are concerns about the hazards that exist when the filter is used in situations for which it was not designed. This work investigates the exhaust gas temperature limits to which the filter elements can be exposed without posing a safety or health hazard, such as 6re or off-gassing toxic compounds. A filter approved by the Mine Safety and Health administration and after-market filters were evaluated under varying engine exhaust conditions to determine if after-market filters pose an unacceptable hazard when used in a DDEF system. Filters were laboratory tested at engine exhaust temperatures ranging from 77°C to 290°C. Of the seven filter types tested, six appeared suitable for use on water scrubber-based cooling systems and two appeared suitable for use on dry heat exchanger type exhaust cooling systems with exhaust temperatures up to 150°C. Any filter elements used as exhaust filters on permissible diesel machines must be approved by MSHA for that application. Mine operators who wish to use an after-market filter element should request an MSHA field modification. MSHA will work with the mine and filter manufacturer to ensure its use in this exhaust system application does not pose a health or safety hazard.

Jan 1, 1995

By Martha Caudill

When planning for the required amount of storage capacity at a proposed open-pit coal mine or determining when additional storage capacity should be added to an existing operation, the decision must be based on a breakeven- analysis relating the discounted cost of capital for storage capacity to the marginal costs incurred for additional crew call-outs on weekends and demurrage charges. The model developed in this paper uses simulation techniques applied to two coal mines in the Powder-River Basin to determine how much storage capacity is needed and when it is needed. The paper also generalizes the simulation model so that it can be applied to any type of open-pit mining operation. Two important results of the model are (1) all of the mines in the Powder River Basin have excessive amounts of storage capacity, and (2) management is provided with estimates of the total number of hours that crews will have to work on the weekends as annual tonnage increases, and the levels of demurrage costs incurred.

Jan 1, 1986

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By G. L. Schroeder, C. H. Summers, D. B. Lindsay

INTRODUCTION The requirement that is placed on owners and operators of underground mines to protect workers against the health hazard of inhaling radioactive materials which are short-lived decay products of 222Rn can be satisfied by applying a considerable variety of what we may call "engineering" solutions as well as a number of "administrative" remedies to the problem. The most obvious of the "engineering" approaches has always been that of forced ventilation, in which relatively clean (i.e., radon-free) air from aboveground is drawn or pushed through the mine workings by a system of fans and ducts. This relatively clean air, in sweeping through the drifts, stopes and haulageways, dilutes the radon and radon-daughter concentrations in the air of the mine, and performs the added beneficial function of removing the daughter-mixture quickly enought to limit grow-in of the longer-lived nuclides in the group that make up the "toxic trio" on which the Working Level (IM) unit is based. Effective as the dilution-ventilation method is for control of WL in most underground mining situations, however, the increasing strictness of control measures that have been imposed on the mining industry over the last two decades have demanded measures of even greater effectiveness. In times of poor markets for yellow-cake and other products of the mines, mine operators are pressed to reduce operating costs, and the installation of additional primary ventilation capacity can be a severe burden on a mine that is already laboring under an unfavorable earning power. When traditional dilution-ventilation systems alone cannot meet the requirement for WI, control, radiation safety engineers and ventilation engineers begin to look at alternatives and auxiliary methods. Since the radon which produces the toxic daughter products originates in the rock of the mine walls, and since, in most United States mines, that rock is a porous sandstone through which air can move under the effect of atmospheric pressure gradients, and through which radon can diffuse relatively freely, one way to help control the growth of WL would be to hinder the escape of radon from that reservior of porous rock. An appealing; method for hindering that natural flux of radon-polluted air from the walls of the mine has long been apparent; namely, to apply a low-permeability coating over the surface of the rock, thus sealing the radon in place and, in theory at least, preventing its escape into the mine air. Our 1970 report to the U.S. Federal Radiation Council on the subject of cost impacts of proposed changes in the occupational standards for exposure of underground uranium miners to airborne radon daughters noted the possibility of using polymeric wall sealants as a means of controlling radon-pollution of mine air. Since that time a number of reports have appeared in the technical literature advocating this technique for restraining the escape of radon from building materials, mill tailings, and other materials containing 226Ra, in addition to the surfaces of underground mine workings. During this period, some controversy has occurred over the question of the probable effectiveness of wall sealants in limiting the escape of radon from the rock. Our 1970 report speculated that flaws (cracks and "pinholes") in the coating might be all but unavoidable in practice, and that even a conservative estimate of the frequency of such flaws would lead to a prediction of ineffectiveness. Hammon et al, in a laboratory evaluation of radon sealants conducted by Lawrence Livermore Laboratory of the University of California in 1975 on behalf of U.S. Bureau of Mines, concluded that a wide variety of polymeric coatings would provide "nearly 100% effectiveness" in restrain¬ing escape of radon from mine wall surfaces if applied in "thicknesses between 5 and 10 mil" (125-250 [y]pm). John Franklin and co-workers at the U.S. Bureau of Mines laboratories in Spokane, Washington, have carried the experiments with polymeric sealants through additional laboratory tests and into actual mine environments, reporting that selected sealants could provide attenuation of radon flux by a factor of four (75-80% reduction). Robert Bates and John Edwards of USBM developed a computer-assisted mathematical/physical model that predicts a relatively small effect of flaws in a low-permeability coating on the radon flux from a sandstone-type matrix. FIELD TEST Since all actual experimental work with wall sealants showed some beneficial effect on radon attenuation (even if not as exciting as the "nearly 100%" predicted by Hammon), USBM was encouraged to extend its evaluation to an actual operating uranium mine, and awarded a contract for that work to Arthur D. Little, Inc. in September 1979. We were fortunate in obtaining the voluntary cooperation of Atlas Minerals Division of Atlas Corp., who operate a mill and several underground mines in and around Moab, Utah. Atlas made available for our use a small T-shaped drift in their Pandora Mine in LaSal, Utah, and provided space for instrumentation and recordkeeping by our field crew in a surface building near the mine entry. Atlas also provided electricity and water to the test site, together with assistance in establishing necessary ventilation, removing rubble from the site, conducting periodic WL surveys and furnishing auxiliary man-power for the heavy hard work of coating the walls with gunite prior to application of the polymeric sealant. The generous coopera-

Jan 1, 1981

By William F. Brandom

INTRODUCTION Cross, et al. (1974), produced a retrospective study of standard setting for underground miners. This report had two distinct components; i) criteria of importance for the protection of the miners, and ii) economic considerations for standard setting. The methods for setting radiation safety standards reviewed were: dose calculations and consensus methods; epidemiology; pathology; bioassay; animal experiments; sputum cytology; chromosome aberrations; and, the Mantel-Bryan Model. By looking back, the authors intended to enable officials to look ahead in making future decisions based on reasonable conclusions. Now it may be time to consider underground miners' protection from another perspective: are there miners who may be especially susceptible to toxic environments?; and if so, are there any biomedical assays that might be indicative of exceptional sensitivities to toxic substances? The human population is genetically very heterogeneous. The data of Saccomanno, et al. (1973), reveal great variability in individual response to radon daughter exposure and only a small portion of the miner population subject to toxic inhalants develop squamous cell metaplasia (Saccomanno, et al., 1970). The majority of the miner population is either not susceptible or is resistant to the toxic agents. This information suggests the existence of a small subpopulation with increased sensitivity or reduced resistance and underscores the need for indicators from biomedical assays that might prove of value for the detection of such individuals. The heightened awareness of the contribution of pollutants in the environment for the potential induction of mutations and carcinogenesis lead to a profusion of short-term bioassays to circumvent the high cost and time-consuming large toxicity animal studies. Over 100 bioassays across taxa from microbes to man are at various stages of use or development (Hollstein, et al., 1979). Less than a dozen tests currently offer early promise for application to[ in vivo] effect studies of man. Many are still in early development, lack the sensitivity needed for a retrospective or prospective study at current permissible exposures, are impractical to conduct in the field, or are not cost effective. The purpose of this paper is to review some of the bioassays that may now, or in the near term, prove applicable for the detection of individual underground miners with increased susceptibility to toxic agents. Throughout this statement, it is assumed that any single test may give false negatives or false positives and, therefore, a tier of tests should be investigated. The possible tests are in various stages of development; some tests better proven than others with a firmer data base and, therefore, with greater probability of usefulness. Some of the less proven assays are not ruled out if they have practical or theoretical promise as indicators. Table I summarizes the assays critiqued for their potential to monitor the effects of [in vivo] exposure to genotoxic substances. POTENTIAL INDICATORS OF HIGHLY SENSITIVE MINERS Assays of Body Fluids It is desirable to have data on the agent(s) to which subjects are exposed when humans are monitored by biomedical effects. Obviously, to varying intensity, the underground mining environments are monitored for radon daughters and it is recognized that the miners are also exposed to other pollutants, most notably, uranium ore dust and diesel fumes. Further testing for the metabolites of the pollutants can be done on body fluid, urine. [High Performance Liquid Chromatography (HPLC)]: This is a very sensitive method for the detection of mutagenic metabolites in urine. The urine is treated with the enzyme sulfatase and beta-glucuronidase to permit identification of substances that are made nonmutagenic by conjugation as glucuronides. The sample is then passed through an XAD-2 resin column and the absorbed organic molecules eluted with acetone. The sample is then split and evaporated to 1 ml and used for direct chemical analysis using HPLC. One drawback to the test is the inability to measure cumulative exposure, but multiple samples can be obtained and comparison to baseline (control) and exposure samples can reveal qualitative differences as a consequence of exposure to mutagens. [The Ames/Salmonella Microbiological Assay]: The Ames/Salmonella microbiological mutagen test is the most extensively used short-term bioassay, with over 2,600 chemicals having undergone testing by this method (Hollstein, et al., 1979). The method, thoroughly worked out and tested for 10 years, consists of taking the second split urine sample from the HPLC preparation, evaporating to dryness and dissolving in dimethylsulfoxide (DMSO). The sample is then applied directly to

Jan 1, 1981

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

The principle of high-pressure interparticulate comminution has been used very successfully since the mid 1980's for grinding a wide range of different materials. A number of reports about operating experience have already been published. High-pressure grinding rolls (HPGRs) are currently making their debut in the mining industry. Experience is being gained with test machines, particularly for the comminution of hard rock. In the grinding of diamond-bearing ore, (Fig 1) interparticulate comminution has already become the standard for liberating the diamonds from the matrix. The advantages of interparticulate comminution are also recognized for the grinding of concentrates (chrome ore, iron ore). Numerous HPGRs are being used very successfully in this field. A testing plant for first-time industrial grinding of coarse, very hard and highly abrasive copper ore was built at Cyprus Amax's plant in Sieretta, Arizona (Fig. 2). The operating experience gained here showed that the grinding of very hard ores places particularly high mechanical demands on the mill. While the machine itself meets the high availability requirements, the wear-protection system proves to be the most sensitive point. Naturally, the properties of the ore to be ground exert a considerable influence on the lifetime of the grinding rolls. This paper describes the wear mechanisms and the wear­protection systems designed to combat these.

Jan 1, 1997