Search Documents

Acid Mine Drainage (AMD) is the most serious environmental problem facing the Canadian Mineral Industry today. Acid Mine Drainage results from oxidation of sulphide minerals (e.g. pyrite or pyrrhotite) contained in mine waste or mine tailings. It is characterised by acid effluents rich in heavy metals that are released into the environment. A new acid remediation technology is presented in this paper by which metallurgical residues from the aluminium extraction industry are used to construct permeable reactive barriers (PRB) to treat acid mine effluents. It describes column tests performed to simulate a PRB using Bauxsol?, a chemically and physically treated bauxite refinery residue, as a reactive material. This experimentation shows promising results for the Bauxsol? PRB method in neutralizing pH and removing metals from acidic mine effluents.

Jan 1, 2006

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By C. Flores, L. G. Twidwell, T. S. Jordan

It is well known that manguniferous silver ores containing manganese intimate) associated with silver are not amenable to conventional extraction methods. The segregation process has been applied primarily to the recovery of copper from oxidized and oxide-sulfide ores. A new alternative process, consisting of segregation roasting followed by flotation to recover the silver from refractory manganiferous silver ores, was studied using a 23-factorial experimental design. Laboratory investigations were conducted on a manganiferous silver ore analyzing 0.02% copper, 0.09% lead, 0.33% zinc, 12.55% manganese and 187 g/t silver. The investigation was designed to study the effects of the addition of salts, coke and copper (11) oxide on silver recovery. The results indicated that 79.3% of the silver can be recovered in the absence of copper oxide and 88.4% of the silver can be recovered with a copper oxide content of 1.5% at 750°C, 2% salt (NaCI). 1 % coke and 30 min of roasting. It was concluded that the addition of copper oxide improves silver recovery.

Jan 1, 1996

By M. M. Rajkovich

Just prior to the close of the century, the Mine Safety and Health Review Commission issued its long-awaited decision in Berwind Natural Resources et al. vs. Secretary of Labor[1] to usher in the new millennium. The case arose as a result of a mine explosion in Eastern Kentucky resulting in the US Mine Safety and Health Administration's (MSHA) issuance of 225 citations, not only to the contractor but to four affiliated entities of Berwind Corp. While an Administrative Law Judge dismissed citations to three of the four Berwind entities, MSHA and the remaining Berwind entity appealed the case to the commission. Although the commission effectively left intact the administrative law judge's decision, it announced a new theory of liability that would apparently be applied in the future, namely the unitary operator theory.

Jan 1, 2003

By Gregg A. Swayre, Roger N. Clark, Stephen J. Sutley, Kathleen S. Smith

Imaging spectroscopy is a relatively new remote sensing tool that provides a rapid method to screen entire mining districts for potential sources of surface acid drainage. An imaging spectrometer known as the Airborne Visible/InfraRed Imaging Spectrometer (AVIRIS) measures light reflected from the surface in 224 spectral channels from 0.4 - 2.5 µm. Spectral data from this instrument were used to evaluate mine waste at the California Gulch Superfluid Site near Leadville, Colorado. Here, the process of pyrite oxidation at the surface produces acidic water that is gradually neutralized as it drains away from mine waste, depositing a central jarosite zone surrounded by a jarosite + goethite zone, in turn surrounded by a goethite zone with a discontinuous hematite rim zone. Leaching tests show that pH is most acidic in the jarosite and jarosite + goethite zones and is near-neutral in the goethite zone. Measurements indicate that metals leach from minerals and amorphous materials in the jarosite + goethite and jarosite zones at concentrations 10 - 50 times higher than from goethite zone minerals. Goethite zones that fully encircle mine waste may indicate some attenuation of leachate metals and thus reduced metal loading to streams. The potential for impact by acidic drainage is highest where streams intersect the jarosite and jarosite + goethite zones. In these areas, metal-rich acidic dace runoff may flow directly into streams. The U.S. Environmental Protection Agency estimates (U.S. EPA, 1998) that mineral maps made from AVIRIS data at Leadville have accelerated remediation efforts by two years and saved over $2 million in cleanup costs.

Jan 1, 2000

By John A. L. Campbell

Although there has been an increased interest in the electrokinetic properties of coal (1) research on the subject is still in an early stage of development (2,3,4,5,6,7) To the author's knowledge, no electrokinetic studies have been made on coal lithotypes - particularly anthracite lithotypes. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods, It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published (8). The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results, however, the results are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation.

Jan 1, 1969

By Peter Ralph

All copper ore haulage at Isamine was transferred to the new 19 level haulage network by mid 1975. Previous experience together with design studies had indicated that a three train operation would be required to haul the scheduled ore production. The ore train with a gross weight of 600 tonne is made up of 15 bottom dumping trucks hauled by twin electric locomotives (Figure 1). Present train speeds reach 40 km/hr and, in the future, this speed could be increased to 55 km/hr. The planned operation on the restricted track network and the relatively high train speed meant that the train driver operated block light system would be inadequate on the grounds of haulage safety and meeting production targets. Some form of Centralised Train Control (CTC) system emerged as a necessity, and as an initial step, tenders were called for a relay control type CTC system. The high cost of these systems and the anticipated high maintenance costs and inflexibility of the offered systems led to the rejection of the tenders. It was decided to develop a CTC system locally and to use a digital computer to perform the basic track [ ] equipment interlocking tasks and monitor haulage operation.

Jan 1, 1979

By C. E. Jordan

The Bureau of Mines conducted research to measure the improvement provided by fine bubbles on the flotation of fine-sized particles (minus 20-um size) in an effort to improve flotation efficiency in our domestic minerals industry. The turbulent velocity distributions of the fluid within the flotation cell were measured as a function of time and position and used to increase the precision of a fine particle, turbulent flotation model. For the mineral system investigated, improved flotation response was obtained under laboratory conditions by using small bubbles and intense agitation. These results matched the model's predicted response.

Jan 1, 1989

By G. Henry, S. J. Domvile

Arsenic management practices at the Con Mine in Yellowknife, Northwest Territories have evolved over the last fifty years of operations under changing regulatory, economic and technological conditions and incentives. As a result of a processing upset in the mine' s arsenic trioxide reclamation plant circuit in August 1988, arsenic levels in the mine' s tailings pond rose from 30 to over 100 mg V. At these arsenic levels, water treatment operations were unable to meet water licence discharge criteria and the mine itself was under risk of closure due to limited water storage capacity. Under these internal pressures, the mine initiated its own research initiatives designed to restore water treatment operations. The new process developed from the mine's research, utilized the mine's existing water treatment plant hardware but introduced a pretreatment step involving a discrete sludge recycle and removal system. In February 1989, water treatment operations resumed under the new process.

Jan 1, 1992

By Carlos Álvarez, Sergio Sánchez, Michael Mains, Giuseppe Gaspari

Extensive record of tunnels excavated with SEM (sequential excavation method) in swelling grounds exists in literature: global experiences include successful tunnelling both through clayey and rock masses with time dependant deformation. However, TBM (tunnel boring machine) use in swelling conditions with high water pressures (EPB, earth pressure balance, machines or slurry shields) is much less documented, considering the lower expected impact due to the limited stress relief and operations under saturated conditions. This paper summarizes a number of studies conducted as part of the risk assessment and detailed design of a large diameter TBM tunnel in variable and challenging geological conditions. The tunnel alignment is driven through mixed face conditions including swelling soils and clayey soft rocks, prone to intense time-dependent deformations. The paper also describes the approach adopted for the design of pre-cast segmental lining subject to both swelling actions and high seismic loads, due to the regional active tectonic faults. The design of this lining included a detailed parametric study performed to handle the existing uncertainties related with ground characterization, potential deconnement and complex geological congurations.

Jun 23, 2024

By Richard Keith Corbin

INTRODUCTION The purpose of this paper is to assist explorationists and entrepreneurs in deciding whether to invest in gold mining concessions in lesser developed countries (LDCs) and, if so, in deciding which LDCs provide the best opportunity. The first decision is difficult in the face of common notions that foreigners are not welcome - only their money; that the best gold deposits were worked out long ago; that even if you survive the mal- aria, and in spite of 51% control by a national partner, you manage to profit from a new discovery, they will tax your operation to death, or worse yet, nationalize it. Close scrutiny of what happened to foreign investors in LDCs during the “Mexicanizationt” of the 1930's through the "Zambianization" of the 1970's shows that many of these concerns are well-founded historically. But the trend of knowledgeable writers over the past decade seems to be away from this gloomy foreboding, and towards a cautious optimism, based on recently perceptible metamorphoses in certain LDCs' conditions and attitudes. If the explorationist or entrepreneur decides to seize on this apparent opportunity, the second decision -- which of these certain LDCs to invest in -- is doubly difficult, because of the formidable tasks of coming up with a rating system to provide rational comparison, and then gathering enough current, reliable information to apply. To assist in these tasks, a suggested rating system and case studies, respectively, follow a brief review of recent writings on the subject

Jan 1, 1987

By Tom F. Deems

The term ball clay is applied to plastic sedimentary clays that have a high content of kaolinite and that possess white firing properties and high green strength (Mitchell and Stentiford, 1973). However, the name ball clay is not derived from any specific property of the clay. Instead, it comes from the original method of production in southwestern England (Scott, 1929). From open pits, the clay was cut into cubes with hand tools. The sides of the cubes were about 220 to 250 mm (9 to 10 in.) and weighed 14 to 16 kg (30 to 35 lb.). The eventual rounding of the corners with handling before sale gave rise to the term ball clay. Ball clays provide the workability and green strength required by the whiteware section of the world's ceramic industry. The main applications are in the sanitaryware, tile and tableware sectors. Each, though, requires particular technical properties in the ball clay component. The clay has to be as white firing as possible for all applications. However, for sanitary-ware, the rheological properties are most important. For tableware, fired whiteness and freedom from specking are the main criteria. Tiles need a reasonable green strength but the clay also needs to be cost-effective. The technical properties of the individual clays in any deposit depend on the clay mineral assemblage. This, in turn, depends on the geological formation of the deposits. Hence, it is the latter that largely determines the market sector for which the clay blends from a particular deposit are suited. Formation of ball clays Ball clays are formed from three main components - kaolinite, micaceous minerals and quartz - while carbonaceous material is also often present. The crystallinity of the kaolinite and mica varies. There are also occasional minor occurrences of feldspar, chlorite, montmorillonite andmixed. layer minerals. Marcasite, siderite and anatase also occur in small amounts. The properties of the clay depend on its mineralogical composition and its particle size distribution, particularly in the lowest size ranges. The original source rocks and the environment of deposition of the clay are the controlling factors. The importance of weathering processes in the formation of ball clays has long been recognized (Bristow, 1968). The diversity of source rocks produces considerable variation in the clay minerals formed. Therefore, each deposit is unique, with time-related variation within it. The greatest development of a weathering mantle takes place in a tropical climatic environment. Plant remains confirm that most ball clay deposits were formed under hot and wet conditions. Sedimentation of the clays had to be in fresh or low salinity water or clay minerals detrimental to whiteware manufacture would have been formed. Fresh water traps for the ball clay, sand and lignite sequences depended -on tectonic features, such as basin development along fault zones or lakes and lagoons on the edge of a large scale embayment. These factors for Devon ball clays were discussed by Vincent (1983). The combination of suitable source rocks, tropical climate, significant fresh water sedimentary environment

Jan 1, 1997

By J. G. Groppo

Froth flotation has been shown to be an effective method for reducing Loss-on-Ignition (LOI) of ponded or landfilled fly ash. Reduction of LOI is required for many fly ashes, particularly those produced from low-No, burners, in order to meet ASTM requirements for use as a mineral admixture in Portland cement concrete. An additional ASTM requirement, fineness, is critical in determining end use applicability, and in many cases, classification of fly ash is necessary to produce an acceptable product. Hydraulic classification has been shown to be a simple, cost-effective method for classification of a variety of minerals including silica, phosphate, mica, coal, etc. and has shown to be similarly effective on fly ash. The combination of froth flotation and hydraulic classification facilitate the production of a high quality pozzolan that meets or exceeds ASTM specifications. This combination has been rigorously evaluated and results of pilot-scale testing are presented. Pilot scale testing was conducted on fly ash from two active utility storage ponds and demonstrated that high quality, consistent pozzolan could be produced using APT's Fast Float? Technology. Along with the pozzolan, additional production of aggregate for masonry mortar and a low sulfur, medium Btu fuel were also demonstrated. The Fast Float? process incorporates several simple unit processes to ensure pozzolan consistency; classification controls particle size distribution which is critical to achieving early strength, flotation controls the grade with respect to L.O.I. (Loss on Ignition) while dewatering controls the moisture content.

Jan 1, 1998

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979

By Mohan Dutt

This paper is concerned with applied platinum resistance thermometry which involves many considerations absent in precision thermometry. The historical development of the Callendar-Van Dusen Equation which describes the resistance- temperature relation of pure platinum is discussed. The advantage of using platinum resistance temperature sensors over thermocouples is described, and the improvements in design and construction of these sensors that have come about in the past few years are discussed. Integral and remote bridges that convert resistance changes into voltage together with signal conditioning techniques and equipment for voltage or current signals are described. Errors encountered in temperature measuring schemes and methods to reduce these errors are summarized.

Jan 1, 1969

By Christopher Nelsen, Daniel Dobbels, R. Zachary Hollenbeck

Recent major floods have inundated Historic Ellicott City, Maryland, resulting in loss of life and property damage. Howard County, Maryland, has developed the Ellicott City Safe and Sound Plan to mitigate the risk of flash flooding in the Historic District, including a proposed stormwater conveyance tunnel. Challenges to overcome include thick zones of saprolite along the alignment, multiple near-surface structures, and minimal rock cover under an active railroad, while minimizing impacts to the public and historic structures. The project will also pursue recognition through the ISI Envision verification process.

Dec 1, 2022

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

"INTRODUCTION The characterization of groundwater hydrogeology is a common component in feasibility studies, geotechnical investigations and regulatory permitting for mining operations. The lithology at a location of interest may include several discrete water-bearing units; and the means of isolating each for testing can be accomplished through the use of inflatable packers. Consideration for testing during drilling program planning and communication between all stakeholders is essential to ensure that the Mine, Drilling Contractor and Hydrogeological Testing Specialist (Specialist) are ready to perform packer testing when the call is made to mobilize. Often, the notice to mobilize can be delayed and then occur with little warning due to the issues that can occur during drilling of very deep boreholes, as well as other factors. Hydrogeological investigation reports and journal articles generally discuss testing methods and results, with limited information available describing the planning and coordination of the field testing program, as evidenced by the lack of references cited below. The source of inspiration for the subject matter of this paper is grounded in the author’s past shortsightedness; with the hope that others not share similar misfortunes but experience success through thorough preparation for their future hydrogeological testing programs. The sections below focus on the planning stages of a field investigation using inflatable packers, including considerations for site specific conditions, designation of stakeholder responsibilities, and communication of testing expectations. Following these sections is a presentation of two examples of successful field programs and lessons learned in addressing problems encountered along the way. PRELIMINARY PROGRAM PLANNING & CONSIDERATIONS From the onset of planning for drilling programs, the Specialist should be in communication with the Mine to review plans and identify fatal flaws which could impede collection of hydrogeological data. Preliminary scope decisions can significantly affect the budget and duration of hydrogeological field programs and may dictate the means by which the field data is collected. The issues that need to be considered include the following factors. Testing Objectives The setup of the packer tool is dependent on the testing objectives. Is the goal to estimate bulk aquifer hydraulic conductivity or to identify discrete discontinuity hydraulic characteristics? Are groundwater samples needed? The answers to these questions affect selection of test interval length and what instrumentation might need to piggyback on the packer tool. Identifying the testing goals initially will provide adequate time to prepare packer equipment for mobilization. Borehole Size While inflatable packers come in many shapes and sizes, some sizes are more readily available and easier to procure on short notice. Packers for NQ and HQ size boreholes have been historically easy to procure and are commonly used in exploration drilling. Packer equipment is available for smaller holes, but it becomes more difficult to fit instrumentation down-hole as the borehole size decreases. This is particularly a consideration if collection of groundwater samples is required. In addition, risks of losing the hole or equipment downhole are greater for smaller boreholes. Larger boreholes require larger packers and clearly require more effort and heavier capacity machinery to manually manipulate due to the increased size."

Jan 1, 2017

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012