Search Documents

By Tomás Vergara, Marcelo Vergara, Alonso Pereira, Fernando Concha, María V. Gutiérrez, Fernando Betancourt

Filtration of copper concentrates in the mining industry is carried out in cycles, mainly cake formation, expression, and blowing. Each of these cycles depends on the solid (mineralogy, porosity, particle size distribution), water, and air (density, viscosity, permeability, and relative permeability) properties that define the performance in each cycle. The fundamental phenomenon in cake formation and expression is a one-phase flow (water) through a porous bed of solid particles (the cake), while in blowing it is a two-phase flow (water and air) through the cake. Sometimes, due to a change in the properties of the mineral, a filtration plant is unable to maintain the capacity at the specified humidity. One alternative to solve this problem is to heat the air during the blowing cycle, which in turn heats the water in the cake, this process significantly decreases the water viscosity and only marginally increases the air viscosity. In this work, this strategy was studied at a laboratory scale. The results show a significant decrease in the blowing time as the temperature of the air was increased.

May 24, 2022

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By G. Swiatnicki, w. Chruscielewski, T. Domanski

INTRODUCTION The inherent errors of simple passive track detectors /SPTD/ used for estimation of exposure to the radon daughters /RnDP/ amount to about 30% /Do75/ while for active detectors only reach about 3 - 4% /Ph78, Du79/. The large error inherent in SPTD is the result of strong dependence of its calibration coefficient on the equilibrium Rn RnDP in the vicinity of detector /0r80/. Nevertheless the SPTD shows many advantages and seems to be very useful for to the estimation of individual exposure of miners to RnDP /Do81a/. For this reason the investigations are undertaken to improve SPTD so that it might provide information about the equilibrium Rn : RnDP during exposure. If the equilibrium would be known then one could use a suitable calibration coefficient yielding a better precision of the measurement. So far, some investigations of the improved type of SPTD have been conducted. One was based on the concept of using the so called diffusion barrier permitting to differentiate the tracks originating from Rn and RnDP /Fr77/. Such improved detector has been named a passive differentiating track detector /PDTD/. However, own investigations have shown /Do81b/ that this type of detector cannot provide precise informations about equilibrium Rn : RnDP. For this reason the investigations of the new idea of PDTD have been carried out. The new model presented below is based on the use of the absorbers of alpha particles. THEORETICAL CONSIDERATIONS The first variant of the concept is as follows: The differentiating detector consists of two portions of detective foil /track detector/ but only one is covered with an aluminium absorber. Thickness of the absorber is carefully selected so that only RaC' particles /7.7 MeV/ can pass the barrier. The second portion of the detective foil records all alpha particles originated from Rn and RnDP i.e. works like a SPTD. The scheme of such a detector, the so called two-fields passive differentiating track detector /PDTD-2/ is shown in the Fig. 1. It is possible to introduce a parameter that can characterize the equilibrium Rn RnDP, namely, the so called track density ratio /TDR/. The definition of this parameter for the considered type of detector is TDR2 = D1•D2-1. One can expect the simple proportion to hold: [ ]

Jan 1, 1981

By John J. Dran

Large mining companies use a number of sophisticated analytical techniques for introducing the element of risk into the valuation of mineral reserve sites. These methods include, but are not limited to, sensitivity analysis, computer simulation, conditional probability, and portfolio theory. Such techniques enable the managements of these large companies to have an awareness of the many possible ramifications of their investment decisions. On the other hand, small mining companies and individuals in the mining business, due to limited financial and technical resources, still rely primarily on single point estimates of the value of mineral reserves. These small miners introduce the aspect of risk only through the application of an appropriate "speculative" discount rate. This paper illustrates the application of a technique for the introduction of risk into investment analysis. The method appears to be most suitable for use by small mining companies and individuals contemplating a large investment in a new mineral reserve site.

Jan 1, 1974

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By R. Yang

This paper presents a kinematic approach for blast modeling with examples of blast models that were developed previously. A kinematic approach was applied successfully in developing blasting models that can simulate all blast design parameters for field applications. Several applied blasting models have been developed and applied widely in the world. A kinematic approach to blast modeling refers to using measurements of kinematic quantities such as the velocity, strain, or displacement and well-established assumptions to model blasting phenomena, rather than being restricted to use first principal of physics, such as, the stress- and material-constitutive relations. The kinematic quantities are easy to measure in the field. Due to the complexity and inhomogeneity of rock mass properties, using first principles of physics, many parameters of rock and explosive properties must be involved, which are hard or impossible to quantify. This creates a major impediment when trying to simulate the total process of blasting based upon first principles of physics. The 3D kinematic model for muckpile formation was developed and applied to open pit blasts. The multiple blasthole fragmentation model developed during recent years has been applied successfully to many mine sites around the globe. These models are typical examples of blast modeling using the kinematic approach, which enables the models to catch major trends of the blasting process and explicitly simulate full blast design parameters and complex geometries. Blast modeling using the kinematic approach results in easy model calibration and validation against field measurements and effective applications to practical problems. Using kinematic models of the muckpile formation and the multiple blasthole fragmentation model, this paper demonstrates the merits of the kinematic approach for blast modeling. New developments of the models were also presented in the paper, which illustrate the potential of the kinematic modelling approach.

Mar 2, 2022

By Luc Morin

What you don't know won't hurt you! This attitude can get you into trouble when considering your process! When trying to extract the most and the best possible performance from a mineral processing circuit this should be reworded to say: What you don't know about your process will hurt your profits! Today, with the popularity of joint ventures, custom milling contracts and process audits by specialists, not knowing is a formula for trouble! Good Sampling Systems are no longer considered a luxury' Not too long ago the practice of grab sampling was considered acceptable and became the norm. Today, it is rare to hear metallurgists say, "All I need is a trend not a good representative sample. so I'll just grab a sample every few hours." Buyers and sellers of quality products have found that grab sampling leads to poor partnerships'

Jan 1, 1999

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By Russell. A. Smith

This paper describes some recent work on the identification and development of new chemical reagents aimed at improving the industrial processing of phosphate ores by froth flotation. In particular, three chemical product families which will be discussed appear to offer enhanced flexibility by: 1) utilizing a small amount of a silica control reagent which can significantly reduce the amount of anionic (carboxylic) collector required for a given P2O5 recovery level; 2) utilizing a new anionic collector family which offers high P2O5 recovery and selectivity versus standard carboxylic collectors; and 3) utilizing another new anionic collector family which has, in some tests, allowed for selective removal of dolomite from apatite. Examples and use characteristics of each of these new chemical ideas will be presented.

Jan 1, 1993

By Dennis L. Boley, Francesco Gallavresi, Donald A. Bruce

The authors describe novel aspects of ground reinforcement and treatment as related to soft ground excavation for tunnels throughout the world. Insitu reinforcement for cut slopes (soil nailing), as underpinning (reticulated micropiles), and as direct tunnel support (infilaggi) is introduced. Ground treatment focuses on new aspects of permeation grouting (by the tube'a manchette system), and on jet grouting-a very powerful and positive new technique. Recent developments in equipment, materials, methods and instrumentation are reviewed, with special reference to major tunnelling projects in Italy and Singapore.

Jan 1, 1987

By James Humphrey

There is a natural resistance to change in any form. When it comes to implementing a game-changing technology like autonomous haulage on an operating mine site, the resistance can at times appear insurmountable. Whether based on real information or misguided preconceptions, it?s essential that we don?t underestimate the effort it will take to overcome this resistance, while clearly recognizing when it?s worth the effort. These realizations did not happen overnight for sites where autonomous haulage has been implemented. Nor did they happen overnight for manufacturers of autonomous mining equipment. Caterpillar, for example, began building toward autonomy more than 30 years ago and had a truck operating in the mid-1990s. Lessons learned during those early years led to the realization that there was much more to be learned ? not just about the machines themselves, but about the systems and knowledge that must be in place for a successful implementation. Working closely with customers, initiating real-life demonstrations on mine sites, having discussions with regulatory agencies and other stakeholders ? these and many other activities were necessary before autonomy could be fully and successfully launched. After decades of effort, Caterpillar?s first official commercial autonomous mine site went to work in 2011 in Farmington, NM.

By H. Yoon

Several processes involving injection of sorbent and humidification water downstream of the air preheater in a coal-fired boiler unit, are being developed as low capital cost retrofit S02 control options. Extensive laboratory work, pilot plant programs and larger scale programs have developed performance data and design information. Many of these programs were supported by the U. S. Department of Energy (DOE) as "proofs-of-concept" of three different processes proposed by Dravo, Bechtel and General Electric. Based on these project results, DOE formulated a comprehensive in-duct sorbent injection development program to fully commercialize the technology by 1992. Also, EPRI will conduct a 4 MWe pilot program to develop its HYPAS process. The Consol Coolside process is scheduled for utility demonstration in 1989 on a 104 MWe unit at the Ohio Edison Edgewater Station under partial sponsorship of the DOE Clean Coal Technology Program.

Jan 1, 1989

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By Javad Sattarvand, Amin Moniri-Morad

Predicting equipment failure behavior plays a critical role in providing a safe operation. Although various reliability evaluation methods are available for estimating failure behavior profiles, these approaches are based on mathematical formulation, leading to actual operation simplification and improper estimation of failure trends. This study proposes a discrete-event simulation (DES) approach to model fleet failure behavior. This approach can model the maintenance strategies in multi-component systems with minimum simplifications. In this regard, the first step was to collect a historical failure time dataset (e.g., the time between failures). Then, the DES model is established to predict the severity of failure events and design maintenance strategy considering actual operation circumstances. Afterward, the maintainability analysis was performed to estimate equipment downtime and availability. The achieved results showed that the system availability was about 85%. Also, the findings demonstrated that the DES could efficiently predict the equipment failure behavior using various stochastic events.

Jun 25, 2023

By P. Huttagosol

The use of computer models to design ultimate pit limits during feasibility study and long range mine planning is becoming a significant practice in open pit mining. One of the problems in determining optimal ultimate pit limits using true optimization techniques has been they require a great deal of computer memory and execution time. In this paper, the maximum closure of a graph, which is a true optimizing model developed by Lerchs and Grossmann, is modified for solving ultimate pit limit problems. By using some properties of the original L&G graph algorithm, the tree configuration can be reduced to only connections between positive ore nodes. The modified algorithm is shown to require less memory and processing time while still yielding an optimal solution.

Jan 1, 1989

By David Mast, Irwan Halim, Brian Hagan, Kaveh Talebi, Jason Edberg, Amanda Foote

On June 14, 2023 Jay Dee Contractors’ Tunnel Boring Machine (TBM) “Phoenix” holed through and completed mining the second drive of the I-75 Segment 3 Storage and Drainage Tunnel. Completion of the tunnel came only after overcoming several challenges, including a groundwater intrusion event which deposited thousands of cubic yards of wet ground material into the tunnel. This paper will discuss the events which delayed completion of the tunnel by over nine months, the risk management and construction approaches assumed by the Design-Build team during bid, several challenges faced by Design-Build teams when building stormwater resilience tunnels using traditional Department of Transportation standards, and recommendations for improving risk allocation and proposal documents for future similar Design-Build tunnel projects.

Jun 23, 2024

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016

By Michael N. Greeley

The movement to reclaim abandoned mine sites has gained momentum as federal, state, and private organizations have increased their commitment and resources to tackle mutual, and often controversial, problems of health and safety. Numerous interorganizational agreements have been implemented to promote cooperation in the characterization of mine site hazards, development of mutually acceptable plans of remediation, and sharing of actual cleanup requirements. Working through these partnerships, the federal land management agencies have begun to focus on abandoned mine reclamation in selected, priority watersheds and other drainage basins. Although there are major difficulties to overcome, significant progress continues to be made.

Jan 1, 1999

By Nathaniel Wollman

About nine years ago the President's Materials Policy Co commission under the chairmanship of William Paley released its report entitled "Resources for Freedom." Not long ago the Senate Select Committee on National Water Resources under the chairmanship of Senator Kerr released a study entitled Water Supply and Demand. Both reports contained projections of future water user the report for 1975, and the Select Committee print for 1980 and 2000, It is my task to compare the two reports. In the initial letter from Mr. Kazmann arranging for thus session he suggested that I present "a critical evaluation of the Paley Report's section on water ?ten years later,? which might include a comparison of predicted and actual water-use rates and would spotlight the assumptions which lead to errors in the predictions , . ." It is possible to compare the results of both studies, and it possible to explain art of the differences that can be found between them. The remainder must remain shrouded in doubt, since the Paley Report did not give all details of the methods used in estimating the com¬ponents of water use.

Jan 1, 1961