Search Documents

By Timothy D. Gardner, Christopher Mark

Coal mines in the Illinois Basin have not engaged in pillar recovery for many decades. In large part, this is due to the exceptionally weak nature of much of the roof in the region. But, as room-and-pillar mining is conducted at greater depths, and larger pillars become necessary, recovering them becomes more attractive. Recently a western Kentucky coal mine became the first in recent times to successfully employ full pillar recovery. This paper describes the many challenges that were overcome during the process. From the beginning, the focus was on protecting the miners from roof instability, using cable bolts, mesh, mobile roof supports (MRS), and engineered final stumps. Two short test panels were extracted first, and the results were used to adjust the support pattern and mining sequence. Further adjustments were made based on subsequent experience. To date, seven panels have been recovered without a ground fall injury.

Jul 1, 2023

By James J. Komadina

INTRODUCTION Newmont Gold Company's Rain operations are located in Elko County, Nevada, approximately 9 miles southeast of the Town of Carlin.The property was submitted to Newmont Exploration Limited in 1979 and underwent development drilling over the course of the next four years, culminating in the completion of a project feasibility study in October 1986. Initial project scope included development of an open pit mine, an 815,000 DSTPY heap leach, a 572,000 DSTPY mill (Mill No. 3), and associated support facilities. Approval to proceed was given by Newmont Gold Company management in June 1987. Detailed engineering began in early July, followed immediately thereafter by procurement of major equipment components through various second hand sources. PROJECT DESIGN Keep It Simple In early August, Newmont Mining Corporation, parent company of Newmont Gold Company, became the takeover target of an "investor" group headed by T. Boone Pickens. Details of the ensuing events have been well documented by the press; suffice to say their impact on this project was material and required immediate flowsheet changes. Project design throughputs were increased to 1,000,000 DSTPY and 760,000 DSTPY for the heap leach and mill, respectively, in mid- September. These changes caused major project headaches as all general arrangement drawings had been approved and structural steel as well as concrete contracts were in place. Additionally, ground breaking was to commence in two weeks time! Rain project management assembled shortly after the announced changes, to devise an engineering and construction strategy capable of handling these new business conditions. The project had been justified using a gold price of $325 per ounce with a forecasted overall cash cost per ounce of $230. Hence, strict control of capital expenditures was necessary to maintain development economics. Mill start-up had also been moved forward one month, to August 1, 1988. To meet an already ambitious schedule, construction techniques needed to be simple and proven as most of the facilities were planned for erection during winter at a site with design criteria of -40F and 90 mile per hour winds. Perhaps the most critical factor requiring consideration was that of personnel. Newmont Gold's revised business plan called for corporate-wide production increases from 587,000 ounces per year in 1987, to 1,400,000 ounces by mid- 1989. Labor requirements were forecasted to grow from 900 employees to over 2,100. This fact, in combination with the rapid growth of Nevada's gold industry, led to the expectation that turnover of operating personnel would be extremely high. It was concluded that, to meet cost, time, and operational goals, the necessary strategy could be succinctly put - "Keep It Simple." Mining/Metallurgical Factors The Rain deposit consists of three interconnecting mineable shapes with host rocks ranging from 90%+ barite to a highly silicified jasperoid. Due to a limited number of mining faces in the first two years, in-pit blending

Jan 1, 1990

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By Richard C. Smith, Steven H. Brown

Commercial scale in-situ leach uranium facilities (i.e., solution mining) have operated since late 1975, and have begun to appear in increasing numbers in the last few years. Solution mining involves the pumping of ground water, fortified with oxidizing and complexing agents, into an ore body, leaching and solubilizing the uranium in-situ, and then pumping the solutions to the surface where they are fed to a mill. Milling is by conventional means, involving ion exchange, precipitation, calcining and packaging processes. This paper presents an overview of the solution mining process, and discusses an empirical method that has been used to determine the radon gas release rate in Bq (curies) per year for the overall operation of the facility including wellfields, milling processes and waste storage reservoirs. In addition to radon generation on the surface from radium decay, it has been determined that the major component of radon release is associated with the dynamic generation of radon from solutions returning from underground. Process parameters impacting this evaluation and the mathematical expressions developed are discussed. The preliminary data accrued is presented.

Jan 1, 1981

By E. Lovera

Social attention to environmental aspects, steadily increasing in European Countries, has been leading to a stricter regulation of many productive activities. Among them, mining and quarrying sectors have been often censured for their potential and real impacts on land and environment. Referring to dimension stone exploitation (also the terms ornamental stone or natural stone are here used as synonymous), quarries are often concentrated in extractive basins, where the resource is localized with suitable quality and quantity: this fact has sometimes raised critical environmental situations. Nevertheless, dimension stone quarrying represents in Europe a traditional and important economical activity, source of wealth and employment. Moreover, many natural stones take on a ?cultural? value and may be considered as ?classic?, as they have been exploited since antiquity and are element of the architectural heritage of many Countries. The sector relevance demands the research of a sustainable balance between social-economical needs and environmental protection. Actually, very restrictive environmental protection policies have led to severe limitations to quarrying activity, but the results do not seem to be completely positive in terms of sustainability: on the one hand, closing-down stone quarrying activities imposes a shrinkage in local, social and economical development; on the other, quarrying activity is pushed towards developing Countries, environmentally un-protected, simply moving and putting off to next future the problem. The challenge of the sustainable development of quarrying sector ? recently explored in the European Commission?s communication ?Promoting sustainable development in the EU non energy extractive industry? (COM-2000-265) ? should be achieved through a positive link between theoretical statements and practical effects: sustainability indicators may be an effective instrument to assess and monitor the environmental performance of the industry. The paper refers to the development of specific ecological criteria and indicators, which can be useful to measure and predict the eco-efficiency of a dimension stone quarry, finally pointing out where improvement efforts have to be focused.

Jan 1, 2003

By K. Neumann

"INTRODUCTION For many automation and safety tasks in open cut and underground scenarios it is crucial to have highly reliable distance measurements at hand. These measurements can for instance be used to obtain the exact position of a machine in one-, two- or even three dimensions. Research and development has shown interest in the ultra-wide-band technology (UWB) in recent years. While for this technology short range, high speed data transfer is the current main research focus, the technology can also be used for highly accurate ranging applications. Due to the use of a very wide frequency band, it is robust against disturbances of many types (e.g. EMC, rain, dust etc.) and is therefore attractive for the use in mining applications. The wide frequency band also offers benefits for ranging applications. Especially in environments with strong multipath problems such as in underground mines it is possible to focus on the dominant signal propagation path, thus increasing the reliability of the measurements. [1] State-of-the-art UWB ranging equipment claims precision within the range of a couple of centimeters and working ranges of more than hundred meters. At the Institute for Mining and Metallurgical Machinery (IMR) at RWTH Aachen University in Germany a modern UWB system was examined in several laboratory and real life tests to examine the feasibility of UWB bases ranging equipment in mining applications. UWB TECHNOLOGY The term ultra-wide-band denotes radio systems that use an ultra-wide frequency band. A common definition for UWB radio systems is that it needs to work on a frequency bandwidth of more than 500 MHz or a bandwidth equal to 20% or more of the center frequency [1]. Due to the ultra-wide frequency bandwidth UWB systems overlap the frequency spectrum of narrow band radio technologies like Wi-Fi, Bluetooth and other mobile communication systems which use a defined carrier frequency onto which information is modulated on (e.g. by using frequency or phase modulation). In order to not conflict with these other radio applications, it needs to be ascertained that the transmission power of a UWB system on a given frequency is so low that narrow band systems are not affected by it. As opposed to this only a small fraction of the UWB system’s bandwidth is affected by the narrow band system. The unaffected remaining bandwidth is sufficient to reconstruct the original signal, even if additional noise is present. Figure 1 shows the power spectral densities of popular radio standards [6], [7], [8]. A significant driver of research and development of UWB systems has been wireless high bandwidth communication. Using an ultra-wide frequency band is highly desirable here, as the channel capacity is dependent on the bandwidth. So far systems have been realized especially for short distances (e.g. wireless USB or Wireless HDMI) but beyond that, communication systems for long distances (several kilometers) are possible [2]. Advances in semiconductor technology led to a reduction in power dissipation of such systems. This enabled higher integration levels which in turn facilitated smaller solution sizes for space constrained applications [3]. Nowadays, UWB is also used for high-precision ranging applications [4], [5]."

Jan 1, 2015

By I. Chatterjee

The application of microwaves has a demonstrated potential for the ultimate removal of water from fine coal. The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems drilling microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper the dielectric properties of various ranks of coal are presented as a function of frequency and moisture content. The measured dielectric data are incorporated into electromagnetic and thermal models of coal which predict the energy absorption and temperature distribution during microwave heating.

Jan 1, 1990

By Wallace N. Thomas

The present interest in large diameter grinding mills and the rapidly rising cost of the drive in proportion to the cost of the mill establishes a need to explore the drive system in detail. The drive for a seven to eight thousand horsepower mill will cost from 1350 thousand to $600 thousand which represents nearly half the total cost of the mill package, and requires as much building space as the mill proper. Some of the drive components require a longer time to manufacture and the installation time and costs are equal to those for the mill. It is apparent that the drive has become a dominant factor in the overall mill design consideration. A new plant requires a tremendous investment in both time and money. With the high degree of competition in the mining industry, low capital cost is an exceedingly important factor in the development of a project. It is just as important, however, to insure that the equipment is going to perform satisfactorily for the anticipated life of the project without adding unplanned operating, maintenance and replacement costs. This is the position in which the engineer or designer usually finds himself and is really one of his primary functions -- establishing a realistic compromise between cost and performance.

Jan 1, 1969

By David A. Sterling

Approximately 50 percent of the uranium resource of the Free World is in deposits of Precambrian age, principally in lower Proterozoic conglomerates in Canada and South Africa (Uranium Resources, Joint Report, ENEA and IAEA, 1967). Most of the uranium resource of the United States is in Mesozoic and Cenozoic continental clastic sedimentary rocks that fill intracratonic basins. The Atomic Energy Commission is investigating the distribution of uranium and thorium in the Precambrian of the Western United States and the relationship of, time-space-facies patterns of uranium and thorium enrichment in the Precambrian to the major resources of uranium in the Mesozoic and Cenozoic host sedimentary rocks. This paper summarizes the results of preliminary studies of the Precambrian in the Southwestern United States including New Mexico, Arizona, southern Nevada, and southern California (Fig. 1). The host rock provenances for the major uranium resources in epigenetic deposits of Mesozoic and Cenozoic age in the Western United States were in areas of extensive Precambrian exposure along the eastern margin of the Phanerozoic geosynclinal belt (Fig. 2). Mesozoic continental clastic sediments in the Colorado Plateau contain about two-thirds of the uranium resource of the United States. These sediments formed from detritus derived from the Mogollon highland in the Southwestern United States where the Precambrian was extensively exposed (Stewart, et al., 19593 McKee, et al., 1959; McKee, et al., 1956; Craig, et al., 1955) (Fig. 2). A genetic relationship may exist between this provenance and the major uranium deposits of the Colorado Plateau. The Precambrian might be equally important in the genesis of uranium deposits whether the most important process in the formation of these deposits was the leaching of low-order intrinsic amounts of uranium from Precambrian granite or from Mesozoic pyroclastics derived from syntexis of the Precambrian basement rocks (Malan, 1968).

Jan 1, 1969

By W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and trucks at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between the shovel and trucks with the new truck cycle times.

Jan 1, 1968

By Ehsan Moradabadi, Debra F. Laefer

"To more rigorously address tunneling risks to above-ground structures, vulnerability evaluation of all structures along a tunnel route is required. This multi-block area along the route can be considered a district. To fully assess each structure within a tunnel’s zone of influence, a multi-block or district-level model may provide new insights as to risk evaluation and mitigation strategies. However populating such a model with the existing geometry of the built environment poses a major challenge as measured drawings are not readily available for all structures along a tunnel’s route. Cost-effective population of such a model could arguably involve remote sensing data in the form of laser scanning or photogramme-try. However even for unreinforced masonry structures, where external, above-ground geometries can be captured, without a prohibitively expensive building-by-building, in person survey many factors would remain unknown. To consider these uncertainties in an automatic way, a performance assess-ment framework is proposed. Such a framework allows a more rigorous, initial, risk quantification than is currently possible within the simple empirical models generally being used in industry when tunneling risk is initially assessed. This paper introduces (within the allowable space limits of this format) consider-ations for auto-population and application of a district-level, tunnel-risk screening tool. INTRODUCTION Challenging topography, intense urbanization and infrastructure development, combined with limited land availability and a growing awareness of environmental issues have lead to increasing usage of un-derground spaces to control aboveground traffic and provide essential services in metropolitan areas. Tunneling, however, is not without its own risks, especially with respect to aboveground structures whether it be widespread minor damage (Burland et al. 2001) or the more notable, although less fre-quent, large-scale collapses such as the 2003 Shanghai (Allianz 2015) or 2004 Singapore (Magnus et al. 2005) events."

Jan 1, 2016

By S. K. Kawatra, J. E. D. McDonald, S. C. Roache

"The formation of geopolymers from mine tailings using cold-bonding processes is known to be possible. Numerous cold-bonding methods exist, but the hydrothermal processes involving high temperatures and pressures in the presence of steam have been found to be the most ideal. This paper presents the results of successful preliminary studies to apply hydrothermal bonding processes to mine tailings agglomerates. Particle-size analysis revealed the particle size of the tailings waste to be 80 percent passing at 35 µm. The compressive strengths of the tailings pellets were shown to increase with time in the curing vessel, closely approaching the 400 lbf of standard iron ore concentrate pellets. These strengths are sufficient to allow use of the tailings pellets as aggregate materials for asphalt and cement. Additional applications may be possible, including reprocessing to extract more valuable materials and usage as agglomerated road-bed materials, backfills for building foundations, and replacements for sand and lime in cement.IntroductionMine tailings are a waste byproduct of ore concentration and are available in large quantities across the world. Despite their abundance, they have received little attention or consideration for beneficial use. One reason is that the chemical nature of the material is not well known. Another factor that has hindered direct usage is the fine particle size. This raises the questions: what is the composition of the tailings, and how can such fine solids be beneficially used? Because the mining industry produces concentrates, the tailings may be treated as concentrates and processed in the same fashion, but it would be inefficient to consider full sintering or induration conditions for materials that have little ore content. To achieve sustainable operation, the development of technologies to use these tailings is necessary. Mine tailings should not be considered waste, and an “out of sight, out of mind” mentality does not represent a sustainable solution for the future.One iron ore mine in Michigan is estimated to have accumulated more than 400 million metric tons of tailings during its last 30 years of operation, with an additional 180 million metric tons accumulated before the ore body is depleted. These mine tailings currently have no practical use, largely due to a scarcity of knowledge of their true physiochemical nature. It is thought that lack of quality control of the waste material prevents its use, but variability in the unprocessed ore prevents a consistent waste stream composition. The fact that the tailings are available in such great quantities makes them an extremely attractive resource. However, developing a sustainable, low-cost means of repurposing the mine tailings waste as a construction material may only be completed once the tailings are physically and chemically understood. Due to the high silica content of the material studied, cold bonding was determined to be the most viable method for processing the tailings into a usable product."

Jan 1, 2016

By D. S. Yantek, L. A. Alcorn, M. J. Lowe, H. E. Camargo

U.S. National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the U.S. Mine Safety and Health Administration permissible exposure level of 90 dB(A). Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Office of Mine Safety and Health Research laboratory in Pittsburgh. The results show that the entire screen contributes to noise below 1 kHz, and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise in this range from 1-10 kHz. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam™ panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2011

By ANDREW HOBERT, Maoming Fan

Low-cost and environmentally friendly green froth flotation modifiers of plant origin, such as guar gum, carboxymethyl cellulose (CMC) and starch, have been used in the flotation of some sulfide and nonsulfide minerals. This paper discusses the fundamentals, current applications and potential new applications of guar gum, CMC and starch in minerals flotation. In this study, improved flotation performance was achieved using some green modifiers in flotation columns.

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988

By R. M. Carland, F. F. Aplan

Six natural zeolites were evaluated for their ability to selectively remove heavy metal cations from solution. Ion selectivity was found to be Pb+2>Zn+2>Ni+2 and Cu+2>Co+2 from their respective solutions. The presence of K+, Ca+2 and Mg+2 in the actual waters to be used may seriously interfere with the ion exchange and elution of cations from zeolites. Zeolites were found not to be effective in removing precious metals from their cyanide solutions.

Jan 1, 1995

By A. J. Naldrett

Over the past six or seven years important new ideas have been developed concerning the origin of nickel sulfide deposits. To a large extent these have been stimulated by the major nickel discoveries of the Eastern Goldfields area of Western Australia (Woodall and Travis, 1969; Ewers and Hudson, 1972). Prior to these finds, the most important nickel camps were regarded as being associated exclusively with intrusive rocks such as the Nickel Irruptive at Sudbury or the intrusive peridotites at Thompson, rocks that were thought to have no close association with volcanism. Study of the Australian discoveries, coupled with work in South Africa (Viljoen and Viljoen, 1969) and Canada (Naldrett and Mason, 1968; Pyke, Naldrett and Eckstrand, 1973), has shown that volcanic rocks with true ultramafic compositions and extrusion temperatures of 1400 to 1600°C were a common feature during the Archean. Under certain circumstances economic concentrations of nickel sulfides have formed from these rocks, either settling to the base of their associated flows or accumulating in shallow intrusive feeders to the flows. The aim of this article is to show how these ultramafic rocks can be recognized, how the nickel deposits, if present, are likely to occur within them, and what special features characterize ore-bearing examples of the rocks.

Jan 1, 1975

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"PROJECT OVERVIEWThe Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million inhabitants. The project was constructed by a joint venture of four South American contractors (“the JV”), and consisted of the following key components:• Treatment Plant: A 16 hectare area was cleared for the construction of a treatment plant to purify 900,000 m3/day of raw water from the Paraná River and distribute it to the surrounding communities.• Bored Tunnel: Nearly 15 km of 3.6 m inner diameter tunnel, ranging from 18 to 22 m below grade, was bored with two EPB tunnel boring machines to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions: Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access & Ventilation Shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of: one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (Intake and Treatment Plant, respectively), and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installed afterwards. Access Shaft 3, the intermediate shaft located between the launch shaft and the treatment plant, experienced persistent leaks during initial excavation attempts."

Jan 1, 2016

By J. E. Rourke, O&apos

This paper describes the use of rock index property testing to obtain rock properties that a.re useful in the design and construction planning of an underground development for civil engineering or mining projects. The index properties discussed include (1) point load; (2) Schmidt hammer hardness; (3) abrasion hardness; and (4) total hardness. The first two index properties correlate to uniaxial compressive strength and Young's modulus. Discussions are given on the relationship to rock mass properties and the integrated use with semi-empirical, geotechnical design methods. The latter two properties correlate to construction performance parameters and some experience is cited. Examples of data are presented from an index testing program carried out on siltstone, sandstone and limestone rock core samples from a deep borehole drilled in the Paradox Basin of Utah for a nuclear waste repository site investigation.

Jan 1, 1988