Search Documents

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By James J. Scott

In 1910 the United States Bureau of Mines was created. It was the outgrowth of a social problem stemming from the fact that 25,000 men were killed in coal mining accidents for the period 1900-1910. Something had to be done and congress responded to the people's demands by creation of this new regulatory agency. At that time mine operators felt the new agency was too strict but nonetheless new rules were developed and enforced and results were obtained by the industry which reduced fatal accidents to less than 250 per year by 1970.*Social reaction by the general public brought about legislation which created the Federal Coal Mine Health and Safety Act of 1969 This legislation was a direct reaction to the Farmington Disaster. Operators and miners alike said "we cannot operate under this law. It is too strict, requirements are unrealistic, production will suffer, .there will not be any improvement in health and safety, etc." Consider the facts: 1. Health and safety have improved. The 1972 frequency and severity rate was the best ever for the bituminous coal mining industry, Figure 1. 2 .Production per manshift has dropped in underground coal mines. For example, in West Virginia from near 16 tons/m.s. in 1967 to nearly 11 tons/m.s. in 1971-72. However, not all of this loss can be attributable to the Act, but certainly some is. (2) The betterment of the safety of coal mining was a prime motivation behind the coal law and from that standpoint the law has been partially successful, but the loss in productivity has been a real burden to the mine operator. Everyone should recognize that the law says little in regard to production--it only relates to health and safety. Production is management's responsibility.

Jan 1, 1973

By P. Zhang, W. D. Xiao

"A process mineralogy study was conducted to guide the development of a process for the extraction of vanadic oxide (V2O5) and aluminum compounds from bone coal and its ash as well as the production of byproducts. Results show that to extract the targeted metals at higher recovery rates, one must find a suitable agent capable of destroying the structure of the mica and breaking down the lattices in which these metal-bearing minerals occur. For such minerals, metal extraction efficiency is usually low if the approach is simply adding an oxidant that cannot destroy the structure. In this research, a byproduct fluosilicic acid (H2SiF6) at 20 percent concentration from an operating phosphate fertilizer plant was found to be powerful and effective for the leaching of vanadium-bearing minerals such as mica. This environmentally friendly process improved the leachability of valuable constituents in the bone coal significantly, with the leaching rate of V2O5 increased to 94 percent, from 83 percent, and that of aluminum oxide (Al2O3) increased to 75 percent, from 40 percent. X-ray diffraction and chemical analyses showed that the structure of mica can be destroyed using fluosilicic acid either alone or in combination with sulfuric acid. Based on the process mineralogy study, a processing flowsheet was tested, which resulted in a final V2O5 powder product with purity of 99.2 percent and an overall recovery rate of higher than 85 percent. The flowsheet consists of leaching, ion exchange and ammonium precipitation. With this process, various byproducts could also be generated, including aluminum fluoride, cryolite, aluminum sulfate, calcium sulfate, ammonium chloride, sodium chloride and cement admixtures.IntroductionVanadium is an important rare metal broadly used in the production of steel alloys and nonferrous alloys as well as in the chemical field as a catalyst. Vanadium-bearing bone coal and clays are abundant in China, and they contain other valuable metals such as aluminum. Bone coal is a type of carbonaceous shale. The vanadium-bearing minerals mainly exist in mica, kaolin, iron oxides, tourmaline and garnet. According to previous studies (Xiao, 2007; Xu, 1989; Xu and Chen, 1991; Ji and Xu, 1991; Chen and Xu, 1992; Xu and Heng, 1992), vanadium occurs from the isomorphous substitution of V3+ for Al3+ or Fe3 + in the crystal lattices of mica, tourmaline, garnet, dolomite and aluminosilicate minerals. In iron oxide and kaolin minerals, vanadium appears as an adsorption form. The isomorphous substitution of vanadium is more stable in tourmaline, garnet and silicate minerals. Therefore, vanadium in bone coal may exist in three phases: vanadium-containing kaolin and oxides, vanadium-containing mica, and tourmaline and garnet (Xu and Chen, 1993; Xu and Zhang, 1993; Xu and Wang, 1994; Feng, et al., 2005; Lin and Fan, 2001)."

Jan 1, 2015

By H. W. Breathitt

World demand for phosphate rock has increased significantly in the past fifteen years. Prior to the early 1960's, most of the world production was obtained from Florida, North Africa, and Kola. As the 1960's arrived, new mines in North Florida and Eastern North Carolina, as well as expanded production in the Western United States, .increased domestic production. Many new mines overseas have also become significant. This includes countries such as Senegal, Togo, Israel, Spanish Sahara, and Jordan. Limited production, often as by-products, has been noted in South Africa, Brazil, and other countries. In recent years, and even recent months, we have learned of many new areas being considered as potential sources of phosphate rock. This includes Australia, Saudi Arabia, Mexico, Colombia, and Brazil. Many other developing countries have discoveries and are considering their new deposits, often with difficult beneficiation problems, as potential sources of phosphate. These factors all relate to expanded world, population and the demand for more fertilizer products to produce food. In this paper, four areas of the world with different types of phosphate deposits are briefly reviewed to contrast the ore beneficiation problems to Florida procedures--long considered the "standard" of the industry, at least for most of the United States' domestic production. Agrico has three large operating mines in Florida with total production capacity exceeding seven million tons per year. Here, pebble phosphate (+14 mesh material) is produced without the use of flotation, whereas all of the material finer than 14 mesh is subjected to flotation beneficiation to upgrade into high grade concentrates.

Jan 1, 1977

By Kimberlie Staheli

A new sanitary sewer was installed in Pleasant Hill, California using microtunnelling methods. The project consisted of 693 meters of 1372 mm and 1981 mm concrete pipe. A Herrenknecht AVN 1200 was used to install the nominal 1372 mm pipe in three drives. The machine was then fitted with an oversized shield used to install the large diameter pipeline. This articulated shield allowed the excavation of a 2362 mm diameter hole with a 1524 mm machine-- a technique new to North America. This paper reviews the design considerations for the articulated shield and reports on the project challenges and solutions to overcome these challenges.

Jan 1, 1995

By S. Usui

In a previous article1 the methyl stretching vibrations for a series of xanthates and amines were reported, and the frequency of the methyl stretching vibrations in a homologous series of the alkyl compounds were shown to decrease exponentially with chain length and approach a limiting value corresponding to that of saturated hydrocarbon beyond six or seven carbons. These observations were explained quantitatively by the theory of Goto and Takenaka2 who proposed an equation relating the frequency shifts to the inductive effect of polar groups. As a result, the alkyl groups in the shorter chain heteropolar compounds were interpreted as becoming somewhat polar, and a good correlation was observed between the CH3-stretching frequencies and such surface chemistry parameters as contact angle, surface tension lowering, solubility, and critical micelle concentration" The substitution of fluorine atoms, the most electronegative of all atoms, for the hydrogen atoms in alkyl groups was expected to reverse the direction of the inductive effect within a heteropolar molecule, and its effect on the C-F stretching frequency shifts and on some surface chemical properties became of interest. In a recent study the C-F stretching frequencies of a series of normal perfluorocarboxylic acids and a few 1,1' -dihydroperfluoro alcohols were determined as a function of chain length and the results were compared with the corresponding hydrocarbon analogs. Furthermore, the nature of the induced polarity in the hydrocarbon and fluorocarbon groups was investigated through surface potential measurements at the interfaces of air-aqueous solutions of normal butyl alcohol and of l,l'-dihydroperfluorobutyl alcohol and through differential capacity and electrocapillary measurements at the interfaces of mercury-aqueous solutions containing the above two alcohols. Experimental Normal perfluorocarboxylic acids and 1,1' -dihydroperfluoro alcohols were provided through the courtesy of the 3M Company, St. Paul, Minnesota. Normal butyl alcohol was purchased from Distillation Product Industries, Rochester, New York. A Perkin-Elmer Model 621 infrared spectrophotometer was used to investigate the spectra in the frequency region of 1200 to 1270 cm-l with frequency scale

Jan 1, 1971

By Brad Hewitt

Since Campbell Mine began processing ore, there has been a gravity gold recovery circuit. From 1947 to 1982, gravity gold was concentrated through the combination of jigs and mercury amalgamation. In 1982, jigs with concentrating table upgrading commenced and was utilized until the end of 1994. As of January of 1995 to the present, Knelson Concentrators in com­bination with concentrating tables have been employed to achieve a refinable product. An evaluation of the justification used for the last change is the focus of this paper.

Jan 1, 1996

By J. A. Halt, E. Larsen

"The Sydvaranger magnetite mine closed in 1996 due to low iron ore prices and was reopened in 2009. The flowsheet has remained more or less as in the old plant, based upon two grinding steps followed by magnetic separation. The magnetite is free of harmful elements and should be attractive on the high quality market. This requires a concentrate containing less than 2% SiO2, which previously was achieved by amine flotation. Amine was preferred because it could be used with sea water. The use of amine is now restricted by the Norwegian Climate and Pollution Agency. Therefore, testwork to replace cationic with anionic flotation was done. Activation of quartz with Ca or Mg ions prior to anionic flotation was shown by research from 1960 to 1980 to be effective under laboratory conditions. The old research results have been followed up in order to make a commercial process for Sydvaranger. Calcium activation works excellently with all Sydvaranger ores, including the ones containing amphibole minerals, but Ca activation requires the high and not environmentally friendly pH of 12.4. Magnesium activation at pH 10.5 is a little more challenging, because the maximum concentration of MgOH+ is about 100 times lower than that of CaOH+. Fortunately, the major impurity in the main Bjornevatn orebody is quartz, which responds well to Mg activation. The process does not appear to depend much upon water quality, as the silicates may already be activated during grinding and magnetic separation in recycled water. The new process is environmentally friendly, as only well-known household reagents are used; oleic acid or tall oil, dextrin, sodium hydroxide and magnesium chloride at pH 10.5.IntroductionThe processing plant of Sydvaranger Gruve AS (SVG) is located in the port town of Kirkenes in the northernmost part of Norway, 10 km by rail from the high-grade deposit of Bjornevatn. This plant has been able to beneficiate magnetite ore to up to 99.5% purity, as described by Sandvik and Malvik (2001). Using the magnetic properties of the ore and making the most out of its enviable liberation characteristics, the original plant consisted of ball mills and 600-mm magnetic separators. The plant was shut down due to market conditions in 1996 but reopened in 2009."

Jan 1, 2015

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By S. Alpay

Underground mining method selection (UMMS) is one of the most important decisions that mining engineers have to make. Choosing a suitable underground mining method to extract a mineral deposit is very important in terms of economics, safety and productivity of mining operations. In real life, UMMS is one of the Multiple Attribute Decision Making (MADM) problems and decision makers have always some difficulties in making the right decision in the multiple criteria environment. Analytic Hierarchy Process (AHP) and Fuzzy MADM (FMADM) are the MADM tools and can be used for the selection of the best underground mining method by considering the problem criteria. UMMSMADM is a computer program which is based on AHP and FMADM and it can analyze the UMMS problems and produce the best underground mining method considering different deposit shapes and ore bodies.

Jan 1, 2010

By A. M. McKim

6, 7.3 meter diameter autogenous mills at Wabush Mines are undergoing conversion from a radial configuration of pulp discharger to a curved design. Improved discharging efficiency has effectively lowered the pulp level in the mill. The low level operation enhances the grinding efficiency netting a 12% power reduction. Significant reductions to rate of wear has been a spin off benefit. The design incorporates features for holding the assembly solidly in place thus eliminating bolt hole damage and leakers. Preliminary work in one 11 meter mill at Hibbing Taconite did not indicate that all the same advantages were available in their process.

Jan 1, 1982

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By H. B. Charmbury

In Pennsylvania there are two distinct coal regions, bituminous and anthracite, in which the mining conditions and production trends are different. Bituminous mining is more mechanized, and production is increasing. This report is concerned specifically with the bituminous area. The bituminous coal industry apparently is facing a shortage of miners and mine officials which may become acute by 1970. Since 1949, when Pennsylvania had more than 100,000 bituminous coal miners, the number has steadily decreased. There are two principal reasons for the decrease of certified miners and mine officials. These reasons are the fact that apprentices are almost a thing of the past and the fact that the image of the coal miner is a poor one to people in general and to parents in particular. This has contributed greatly to the high average age of our miners today. The average age of all those employed in the mines is 50. Yet it is known that the progress in mine mechanization requires younger and more alert men to operate the newer type equipment.

Jan 1, 1966

By David P. Kimball, Dalva L. Moellenberg

On May 21, 1990, EPA released its Strawman II draft program for mining wastes. It proposes to expand RCRA regulation of mining operations to include materials other than wastes. Strawman I1 would establish strict standards for the states to follow, rather than technical guidance. It proposes to establish performance standards; design criteria; monitoring requirements; and corrective action, closure, post-closure, and financial assurance requirements. It suggests "pollution prevention" concepts for mining operations. This paper explores the Strawman II proposals, particularly the technical criteria, and addresses several of the important concerns raised by industry.

Jan 1, 1991

The Northside Storage Tunnel Project in Sydney includes over 20 km of TBM driven tunnels, over three km of declines and major caverns and pump rooms. The paper describes methods used for design on the project. Emphasis is given to the refinement of the use of empirical rock mass classifications, and to the use of discontinuum numerical methods. The use of empirical rock mass classifications in Sydney sandstone has usually led to conservative design because the systems are based on a random orientation of joints in the rockmass. Because the joint sets are usually oriented in a way that is beneficial for tunnelling, limits must be placed on the parameters used in the classifications system. The paper discusses these limits and the derivation of the parameters. The use of numerical methods in Sydney sandstone is discussed. Continuum methods have their uses, but discontinuum methods are preferred. The use of UDEC has been validated against a previous project, the New Southern Railway. Recommendations are given for UDEC models. In Sydney's geology, so advantageous for tunnelling, the challenges of this project have been to make the best use of the good conditions, while maintaining safety for the workforce and the future operators of the project.

Jan 1, 1999

By Angus Maxwell, Jacob Grasmick

As the tunneling industry continues to adopt Tunnel 4.0, digital twins of the tunnel construction site are becoming standard requirements for tunneling projects. However, the benefits of these remain unproven to many practitioners. The paper discusses the various implementations of digitalization and describes efforts to combine all data types to analyze the relationships between influences, predictions and performance in a single digital platform. This includes data pertaining to investigations, design, construction, monitoring and post-construction asset performance and management. Based on 16 years of global tunneling projects the paper aims to quantify the tangible and intangible benefits of such systems. Using a number of real examples, the paper describes where opportunities were taken and where they went unrealized. Challenges and considerations for both procuring and developing these digital twins are also discussed.

Jun 13, 2021