Search Documents

By D. R. Schricker

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment.

Jan 1, 1990

By C. C. Nolan

As the size of the mills get larger and the liners get heavier, abetter means had to be found to handle liner replacement. McLellan Industries is famous for their innovative ideas andwas called upon by an engineering company to develop a mill liner crane. The first crane was developed for Similkameen about 1969 to serve a 32' Ø X 14' Long SAG Mill. The next was Island Copper in Port Hardy, B.C., the same size as Similkameen in 1970. At that time, we took existing hydraulic cranes and modified them to meet the mill configuration. In 1973, we developed a completely new approach for the Southern Peru copper mine at Tacna, Peru for a Ball Mill, size 16'-6" Ø X 19' Long. Each installation required a design study to meet the change in mill size, trunnion size, elevation of floor to feed trunnion, area at the feed or discharge end of the mill. We have supplied self-propelled units as well as lift in. When there is no room at the feed end and if the mill has a trunnion overflow discharge, we have the mill supplier provide a structural frame to span the sump and move the mill liner handier into position with the use of the overhead crane or a mobile crane.

Jan 1, 1999

By L. H. Munson, D. E. Hadlock, L. F. Munson, R. L. Gilchrist, P. D. Robinson

All uranium mills are required to perform sampling and analysis for radioactive particulates in their gaseous effluent streams and in the environment. Pacific Northwest Laboratory was requested by the U.S. Nuclear Regulatory Commission (NRC) to provide technical assistance to them for their Uranium Mill Health Physics Appraisal Program. In conducting appraisals, air sampling methods used at NRC-licensed mills were reviewed and several deficiencies noted. This paper includes only environmental and effluent particulate sampling although much of the information is applicable to both in-plant and environmental samples. First, the components of a proper sampling program are discussed: program objectives, program design, sampler design, analyses, quality assurance, and data handling. Then the specific deficiencies, or the "pitfalls" from the first 8 mill appraisals are discussed. The first consideration in establishing an air sampling program is defining the objectives of the program. What is air sampling suppose to accomplish? Many of the deficiencies we have observed have resulted because the desired objectives were not clearly established in the minds of the radiation safety staff. PROGRAM OBJECTIVES An environmental air sampling program ought to fulfill the following seven objectives. The first is to: 1) [demonstrate regulatory compliance]. Although a goal of most programs, regulatory compliance, is not well understood. One has not only to comply with the conditions of the source materials licensee, but one must also demonstrate compliance with 10CFR20 and 40CFR190. For example, 10CFR20.106 states: "A licensee shall not possess, use, or transfer licensed material so as to release to an unrestricted area radioactive material in concentrations which exceed the limits specified in Appendix B, Table II of this part .... For purposes of this section, concentrations may be averaged over a period not greater than one year." Even if a mill's license does not require sampling at the site boundary of maximum concentration, a sample may be necessary to demonstrate compliance with 10CFR20. Most mill personnel are painfully familiar with 40CFRl90.10, which states: "Operations.... shall be conducted in such a manner as to provide reasonable assurance that: (a) The annual dose equivalent does not exceed 25 millirems to the whole body.... of any member of the public as the result of exposures to planned discharges of radioactive materials, radon and its daughters excepted... from uranium fuel cycle operations..." This means a licensee's sampling program must give "reasonable assurance" that the member of the general public receiving in the most exposure gets no more than 25 millirems per year. The sampling program necessary to provide that assurance may or may not be a license requirement. However, merely meeting the license requirements and the explicit regulatory requirements does not necessariarly ensure an adequate effluent and environmental air sampling program. The second objective of the environmental air sampling program, is to 2) [identify the source(s) of contaminants]. This will include not only the routine program, but special sampling for verification of sources and nonsources. Only after sampling can a mill operator be assured that roof vents, laboratory hoods, and other localized ventilation systems are not making a significant contribution to environmental releases. An environmental sampling program should also allow the mill operator to fulfill the third objective, to 3) [estimate exposures]. Even before 40CFR190, a sampling program should have provided the mill operator with the information necessary to determine the dose to the "fence post" person, or at least to determine if doses were well below the 10CFR20 limits previously allowed. The program should 4) [detect and measure unplanned releases]. If there is a fire, a scrubber failure, or if a drum of yellowcake breaks open, measured releases will almost always be lower than conservative estimates. Whether or not a system to provide sampling during accidents is needed is almost always a cost-benefit decision. In general, uranium operations do not sample just in case an accident may occur. Yet they may decide on continuous air sampling in lieu of intermittant sampling partially because of the potential for accidents. Another objective of air sampling is 5) [to provide information on the effectiveness of control systems]. This is always a concern with new or modified equipment and may dictate sampling frequency in other situations as well. For instance, if a small leak in a bag filter cannot be detected by other means, then more frequent stack sampling may be indicated. A routine effluent and environmental monitoring program should also fulfill the sixth objective,

Jan 1, 1981

By Archie M. Richardson, Carl E. Brechtel, Tom R. Kelly, Frank Feero

Recent work to upgrade the ventilation system for the el Mochito lead/zinc mine in central Honduras is discussed. Network modeling and underground measurements were used to evaluate cost-effective alternatives for achieving satisfactory ventilation in a complex and expanding underground operation. Both interim and long-term solutions were implemented to make mining possible under difficult conditions. INTRODUCTION Mining operations at the el Mochito Mine, located in the central highlands of Honduras, Central America, have been virtually continuous since the opening of the mine in 1948. Initially a high-grade silver mine, the mine has expanded along a westward trend of pipe-like orebodies to a distance of roughly one mile from two centrally located shafts. Production of the relatively large San Juan orebody at the western most extension of the mine (Paddock, 1981) led to the introduction of diesel-powered equipment; however, the ventilation infrastructure was insufficient to meet the needs of mechanized mining. A succession of owners/operators in the 1980s allowed the existing ventilation infrastructure to decay to the point that ventilation in the production areas of the mine was very poor. Environmental conditions in some working areas were not conducive to efficient ore extraction because of high dry bulb temperature, high humidity, and diesel emissions. Upon acquiring the mine in 1990, Breakwater Resources of Tucson, Arizona began an aggressive program to refurbish the mine infrastructure to complete extraction of the San Juan orebody and to allow the extension of the mine another 2500 ft to the west for extraction of the Nacional orebody. The program included increasing the capacity of the main ventilation system. This article presents a case history of the process of upgrading the ventilation system in a mine where extensive old workings cause large air leakage. This process has been one of selecting solutions to difficult technical problems that are compatible with the existing mine infrastructure and economic constraints. The initial ventilation system is described in the background section, along with ventilation projections for the mine expansion. Field characterization of the ventilation system for design verification and fan specification is then discussed. The paper describes a series of interim changes to the system to improve ventilation pending completion of new ventilation boreholes. In addition, the temperature/ heat problems in the mine are described. BACKGROUND Initial Condition of Ventilation System The ventilation system is illustrated in Figure 1, which shows the extent of mining with the main ventilation paths superimposed. Early mining around the two shafts opened up vertical connections (stopes and raises) over the entire 2420 ft (737.6 m) of vertical extent, and mining progressed to the west primarily using compressed air and electric-powered equipment. Since ventilation was not a complex problem in the original mining system, the stopes and interconnecting raises were not sealed. The San Juan orebody was much larger than the silver ore zones mined previously, being primarily zinc and other base metals. Its geometry, size, and grade allowed the use of vertical crater retreat (VCR) stoping with diesel mucking and haulage equipment. Its depth, along with the existence of warm groundwater, resulted in a mine climate problem on the lower levels. To establish a complete ventilation circuit, two vertical boreholes (Bonanza Nos. 1 and 2) had been drilled by previous owners from the surface in the vicinity of the San Juan orebody. The system design called for air to be drawn down the intake shafts, across the lower mine levels to the San Juan workings, then up through the San Juan ramps and ore passes to these two exhaust boreholes (see Figure 1). In practice, however, only the Bonanza No. 1 borehole was drawing air through the desired path. Leakage across the old upper levels from the intake shafts, the Caliche tunnel, and from intervening abandoned stopes and raises supplied most of the air flowing to the base of the Bonanza No. 2 borehole. In effect, there were two ventilation circuits in semi-parallel through the mine, of which only one was delivering appreciable air to the San Juan workings.

Jan 1, 1993

By James W. Furlow

A recent attempt by a major mining company to mine phosphate in Chatham County, Georgia, resulted in a study by the Georgia Department of Mines, Mining and Geology which was intended to evaluate the deposit as well as potential hazards to the major fresh-water aquifer of the area. The study found that the confining layer above the fresh-water artesian aquifer is sufficiently thick and impermeable to allow removal of the phosphate ore zone without significant salt water infiltration into the aquifer. Therefore, phosphate mining under proper supervision will not adversely affect the quality of water used by the city of Savannah nearby. Volumetric studies show that there is a minimum of 4,800,000,000 cubic yards of phosphate matrix containing an average of 22.5% BPL. At an approximate weight of 1.5 tons per cubic yard and a concentration of 22.5% BPL, there are about 1.6 billion tons of 100% BPL concentrate present. At a conservative factor of 50% at least 800,000,000 tons of 100% BPL concentrate could be recovered for market sale. In addition to the area discussed, evidence indicates that the phosphate horizon-may extend continuously out to sea for at least ten miles, and probably beyond.

Jan 1, 1972

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By A. P. Massmann

Design for economical operation, minimum operating labor and minimum maintenance for labor and supplies are virtually inseparable. Each consideration has a vital bearing on the other. Let us assume that we have the design complete for the most economical operation with a minimum of operating personnel. This means, in addition, that we have the fewest number of operating units consistent with the product requirements for a team or metallurgical coal which we are called on to produce. The number of units will vary greatly, being influenced by design, washability characteristics, tonnage and degree of quality control necessary by reason of producing a product for metallurgical, steam or domestic use. The units involved most ordinarily for any type coal preparation plant will number as a minimum the following: 1. Hoppering R.O.M. Coal 2. Feeding

Jan 1, 1959

By Thomas E. Howard

Engineers today face a tremendous challenge. Growing population and rising standards of living all over the world are creating unprecedented and accelerating demands on and for all kinds of technology. At the same time, the public is becoming more and more conscious of--and concerned with--the impact of technology on human welfare. The growing controversy over the Supersonic Transport is a case in point, It is clear that the modern engineer must expect to spend a growing share of his time considering this dilemma and evaluating the tools that are available to him, not only with respect to their adequacy for the job at hand but also their capability for meeting the increasingly demanding--and, in many cases, conflicting--requirements of the future. This meeting seems a particularly appropriate place to speculate about the future of mining technology. The summary of the state-of-the-art in surface mining contained in the papers scheduled for the International Conference, together with the recently published Surface Mining volume, constitute not only a major contribution to the technical literature but also form an impressive record of technologic progress. That record, and the advanced technology displayed in the exhibits, and to be discussed in the SME technical sessions demonstrate engineering achievement in which the mining community can justly take pride.

Jan 1, 1968

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959

By F. J. Hurst

Phosphate rock, which is a prime source of phosphate used in fertilizer manufacture in the United States, contains uranium. In general, the uranium content of the rock increases with the phosphate content and most high-grade phosphate deposits (>30% P2O5) contain 0.01- 0.02% U3 8. The large tonnages of rock being mined represent a significant potential source of uranium that lends itself to recovery as a by-product of the wet-process phosphate industry. For example, in 1953, the U. S. Geological Survey estimated that recoverable phosphate reserves in the U. S. totaled about 5 billion tons and contained 600,000 tons of uranium. I This estimate did not include any rock from North Carolina which has since been estimated at about 2 billion tons. For the most part, the known, economically mineable U. S. reserves - estimated at about 7 billion tons - are concentrated in a few areas: 43% in the western states of Idaho, Montana, Utah and Wyoming; 28% in each of Florida and North Carolina and less than 1% in Tennessee. In the past, Florida has supplied about 80% of the total U. S. production, practically all of which is land pebble phosphate. All forecasts indicate increased production rates from North Carolina and the western states.

Jan 1, 1976

By Elizabeth Anne Semon

The marketability of a large volume bulk material is significantly effected by transportation costs. Hence, it is essential for anyone that deals with minerals or mineral wastes to be able to reliably estimate bulk transport costs. The three types of bulk overland transportation modes that will be discussed are truck, railroad, and pipeline. Contract and private carriage are the two types of truck transport generally suitable for movement of bulk commodities. Contract carriers are those transportation firms that service a limited number of shippers and geographic points, and carry a restricted number of commodities. Private carriage consists of control over drivers and equipment by the shipper, ownership or lease of the transport equipment, and shipment of commodities related to the primary business of the shipper.1 A combination of private and contract carriage may also be used. Depending on the size and regularity of the shipment, rail offers single car, multiple car, or unit train service to move bulk minerals. Both long and short distance pipeline transportation has been shown economically and technically feasible for many different solids such as, mine and quarry products, coal, chemicals, copper concentrates, phosphate rock, and sewage sludge. 2

Jan 1, 1973

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By Musa I. Marto

The theory of ore flotation has developed at a rather fast rate and the application of theory to practice has been successfully investigated. Significant technological advances have been made in such areas as control of the ore grade, automation in metallurgical control through conductivity measurements, and the development of faster and continuous analytical techniques for ore pulp analysis. Further significant improvements in mill control are being_ investigated through the application of a computer control to the process. This represents the more advanced trend in process control. At the heart of a control system installation, the digital computer will communicate directly with process instrumentation, perform' complex calcu¬lations to determine on a timely basis the control settings for attaining optimum results and automatically furnish signals to effect control actions. The process is considered as an integrated unit and economic criteria are used to measure its performance. The approaches to a mathematical model development to describe the process, optimization and control schemes as applied to an ore beneficiation process will be discussed.

Jan 1, 1962

By Paul Javor

Optimization of a process is achieved by selecting, 'from all the known options, the most beneficial method of obtaining a product. It is rare that the optimum process is arrived at by conventional methods, because of the great amount of time required for developing and comparing all the options. On the other hand, it is now possible, by means of an optimization program based on special mathematical formulas involving an algorithm and implemented by a computer, to plot the optimum process realizing considerable savings and in a reasonably short time. The flow sheet arrived at in accordance with the optimization program described in this paper investigates and develops all the possible options and, with the aid of the computer, makes it possible to select the most economical ore beneficiation process. The options in an ore beneficiation process are all the possible trajectories that can be traced through the particle sizes to which the ore is reducible in the extraction of its valuable minerals. Although an ore can have a wide range of composition and several valuable minerals that can be extracted, this paper is concerned with the special case in which only one mineral is extracted from the ore and in which the maximum allowable percentage of impurities in the end product is defined.

Jan 1, 1971

By J. Hanna, I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pHs without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35% to 38% P2O5, 0.8% to 1% MgO) with high recoveries (80% to 85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P2O5 and 0.8% MgO, with a P2O5 recovery of 76%. A concentrate obtained from the western US phosphate ore from Utah assayed 30% P2O5 and about 1% MgO, with a P2O5 recovery of 89%.

Jan 1, 1988

By George B. Griswold

The two most stringent parameters for in place fracturing of rock are the lack of any initial void space in the rock which to expand into and the ability to gain access only through drill holes. These two restrictions have proven so severe that as of today the only proven techniques for efficient fracturing are the contained nuclear detonation and hydrofracing. Both of these methods have highly developed technologies for their application. Hydrofracing has been a standard oil field practice for two decades, and the experience gained from a couple hundred underground nuclear detonations has resulted in a thorough understanding of the phenomenology of cavity and chimney formation. What is still lacking is a practical method to create a suit- able degree of fracturing for those ore bodies which do not meet the application criteria for either the nuclear explosion or hydrofracing. Nuclear applications must be restricted to thick ore deposits so as to take advantage of chimney collapse height--preferable in excess of 200 feet thick. Other requirements such as ground shock, containment, and radioactive contamination further reduce the number of sites that prudently can be selected.

Jan 1, 1969

In this paper, response surface methodology was applied to optimize the experimental conditions for the wet grinding of synthetic rutile. The effects of parameters such as rotation speed, solids concentration and duration of grinding on grinding efficiency were systematically investigated and the process conditions were optimized, using a nonlinear regression model based on central composite design. The statistical analysis of the results showed that in the range studied, the grinding efficiency of synthetic rutile was significantly affected by the rotation speed of the conical ball mill. According to results from analysis of variance, the value of the determination coefficient (R2=0.9989) indicates that the predicted values are found to be in good agreement with experimental values. The optimized experimental conditions were as follows: a rotation speed of 350 rpm, a solids concentration of 27.31% and a grinding time of 50.31 min, respectively. Under optimum conditions, the predicted grinding efficiency of 94.79% is obtained. The experimental values from the validation experiments were well within the predicted value of the model.

Jan 1, 2011