Search Documents

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

By George D. Coumoulos

The following aspects of diasporic bauxite are discussed: The importance of world reserves of diasporic bauxites; the geological, chemical and mineralogical characteristics of the Greek diasporic bauxite; the uniformity of bauxite deliveries; the significance of the absence of organics; the excellent settling properties of the red mud; the production of sandy alumina from diasporic bauxites; the advantages of applying tube digestion systems in processing diasporic bauxites; the conditions for introducing diasporic bauxite in the existing European refineries.

Jan 1, 1984

By J. A. Reizes, C. A. J. Fletcher, T. Jancar

Spirals play an important role in fine coal and mineral processing. To date, almost all spiral designs have been empirically based. Although many operational units have evolved utilising this approach, it does not necessarily lead to optimal spiral designs. This paper presents the preliminary results of a collaborative computational and experimental research program to understand the detailed separation process which will ultimately lead to a parametric assessment of alternative spiral designs through computational simulation. Unlike the empirical approach, a computational simulation is only subject to the fundamental physics of the fluid flow. No prior knowledge of the generic spiral flow is necessary. The computer code implements a robust finite volume technique to predict the three dimensional fluid motion. A height function method is used to model free surfaces and the code is capable of handling arbitrary spiral geometries. Preliminary validation of the computational simulation is carried out through analysis of an existing spiral design -the Mineral Technologies LD9 unit. Computational flow predictions are compared with experimental measurements obtained using a number of techniques, including sampling and flow visualisation, for flow test cases where no solid particulate is present.

Jan 1, 1995

By R. Bruce Thorndycraft

Pinson Mining Company was formed to develop a gold orebody located in northern Nevada near Winnemucca. A feasibility study was undertaken in 1979 by a consortium of three Toronto-based mining companies and a Reno-based exploration company. The study indicated a viable project with gold priced above $225 per ounce. A project manager, and mine and mill superintendents, were hired in late 1979 to expedite the development of a 1000 ton per day mine-mill complex. Plant design engineering was contracted with Industrial Design Corporation in Salt Lake City. Three experienced plant metallurgists representing Pinson were stationed in Salt Lake to guide the work of Industrial Design. Among the many design criteria spelled out by Pinson, foremost were bringing the mill on line as quickly as possible at minimum capital cost. Fourteen months after the beginning of design engineering, the completed Pinson mill became operational. Total capital cost, including mine development, was $18 million. The Pinson project has proved to be far more than viable; the entire capital cost will be recovered within 18 months of the mill start-up.

Jan 1, 1982

The molecular form of aliphatic amines precipitates in alkaline solutions when the amine solubility limit is exceeded and forms a typical colloidal system. The zones of mines precipitation and micellization are defined and it is shown that the appearance of a colloidal system in a certain pH range is a unique feature that makes weak electrolyte type surfactants differ from strong electrolytes. The formation of iono-molecular complexes reported in the literature is shown to be a pre-precipitation phenomenon. The zeta potential - pH curves for minerals and bubbles in the presence of amines in the pH range where the amine forms a colloidal precipitate are entirely determined by the precipitate. The pH dependence of the flotation of certain minerals using amines is discussed in the light of these findings.

Jan 1, 1989

By Shail J. Butani

This paper analyzes the 1982 coal mine accident data collected by the Mine Safety and Health Administration (MSHA) for key equipment types, by mine type, and by geographic region. The differences in hazards associated with the various equipment types are studied both in absolute (i.e., total number of incidences) and relative (i.e., incidence rate or the number of incidences per 200,000 employee or exposure hours) terms. The paper compares and contrasts the total number of incidents as well as incidence rates classified by several types of severity measures such as lost workdays cases, mean number of lost workdays per lost workdays case, fatal cases, non- fatal cases without lost workdays, total number of cases, and total number of lost workdays This statistical analysis shows that significant differences in hazards exist not only due to equipment type but also due to mine type and geographic region.

Jan 1, 1986

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By C. B. Rash, W. W. Fowler, Gill Montgomery

INTRODUCTION Fluorspar is the common term used for the mineral fluorite, which is naturally occurring calcium fluoride (CaF2). It is the principal source of fluorine, the most reactive of the chemical elements, from which a great variety of unique and strategically important chemicals are produced. Commercial deposits of fluorspar are widespread throughout the world, and its availability is essential to the industrial progress of all nations. GEOLOGY AND MINERALOGY In its pure form fluorspar, CaF2, contains 51.1% calcium and 48.9% fluorine, and has a sp gr of 3.18 and a hardness of 4. It is commonly a glassy mineral. colorless, white, or grayish. but may also be various shades of purple, pink, blue, green, yellow, or tan. It belongs to the cubic system mineralogically, and commonly crystallizes into cubic shapes in vugs and cavities, although most of it is massive, with interlocking crystals. Minable fluorspar deposits, in descending order of importance, occur as bedded limestone replacement deposits along fault zones; fissure-filling vein deposits; breccia filling in limestones, dolomites,

Jan 1, 1985

By H. Fayed

Two-phase (water and air) flow in a self-aspirated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). The geometric model is a replica of a 300 m3 cell. A 72-degree sector containing two blades of the ten-blade rotor has been modeled and periodic boundary conditions are applied in the circumferential direction. Simulation of a sector of the machine allows acceptable resolution of the mean flow field using 4x106 grid points. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Unsteady simulations have been performed. In a self-aspirated machine, airflow rate is not known a prior; it is an output from the CFD simulation. Uniform mean bubble diameter of 0.7 mm has been specified as an input for the simulation. Air flow rate and power consumption have been monitored with time, and results indicate a stable operation. Air volume fraction contours and velocity field in different regions of the machine are presented and discussed.

Feb 27, 2013

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By P. D. Pack, E. H. Skinner

During design of a 550-foot rectangular shaft in alluvium, lateral support within the excavation was an anticipated construction problem. Actual experience showed that the nearly 9 x 14 foot excavation required no lateral support. A strain measurement program con- current with construction and for a 9-month period following completion of the shaft detected only minor strains. Shaft design included consideration of available geological information. Site exploration included a 754-foot drill hole, cored at selected intervals, and a suite of geophysical well logs. Generalized physical properties of the alluvium were developed from laboratory core testing. An elasto-plastic, finite element computer program (DAHLKE) developed by the Spokane Mining Research Center U.S. Bureau of Mines, has been recently used to analyze the behavior of the alluvium around the shaft. Analysis showed that yielding first develops in the shaft corners and progressively expands into the wall zones around the shaft as loading increases. Gradual growth of a plastic zone progressed outward from the excavation boundary at increasing loads but had limited extent and was surrounded at all stress levels by an infinite elastic zone. This design review, aided by computer analysis, confirmed that the shaft would have been considered theoretically stable as designed.

Jan 1, 1977

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be re-handled. Prior studies have shown that by only changing blast hole timing with the same blast design, fragmentation and throw alters. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum inter-hole delay for fragmentation has been found by studying timings from 0ms to 45ms. Instantaneous timing between holes increased the throw by over 100 ft, but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw. This paper investigates this optimized inter-hole timing while altering top and bottom column primer time to potentially improve throw while maintaining optimum fragmentation. Timings studied are top initiation, bottom initiation, and top and bottom simultaneously. INTRODUCTION Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading, and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.” Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is re-handled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators has allowed for precise delay timings to be used between rows, holes, and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation. This study consisted of 3 full scale bench blasts at a granite quarry in Talbotton, GA. Each blast was characterized by the timing delay between the top and bottom primer in the blast column of each hole; one simultaneous blast with a 0 ms delay, a bottom-initiated blast with a 1 ms delay, and a top-initiated blast with a 1 ms delay. Fragmentation analysis of the resultant muckpiles was performed using a combination of the PortaMetrics handheld point-and-shoot rugged tablet from Motion Metrics and the software WipFrag from WipWare. Throw was measured by placing strategic distance markers on the floor of the bench and then taking overhead photographs of the muckpiles after each blast. High-speed video footage was captured of each blast using an MREL Blaster’s Ranger II camera."

Jan 1, 2017

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC), as agent for Phillips Petroleum Company, Sohio Shale Oil Company, and Sun Shale Oil Company, is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub, located in northeastern Utah and known as the White River Shale Project (WRSP). The Ralph M. Parsons Company (Parsons) has been retained as the design engineer/constructor for the project. This paper covers the successful pregrouting of the Bird&apos;s Nest Aquifer in conjunction with the sinking of a 9.2-m (30-ft)-diameter shaft and driving of a 3.89-m by 5.64-m (18.5-ft by 12.75-ft) decline. The Bird&apos;s Nest Aquifer derives its name from the ellipsidal solution cavities caused by leaching of random-size nacholite nodules. The sodium bicarbonate nodules occur as persistent bands within a matrix of siltstone and marlstone. The team, made up of the owner, engineer/contractor, and subcontractor successfully grouted the shaft down to an inflow of less than 0.06 lps (1 gmp) and the decline down to less than 0.12 lps (2 gpm) by injecting a total of 213.190 kg (470,000 lb) of Celtite Terraseal, 113,400 kg (250,000 lb) of limestone dust, and 41,730 kg (92,000 lb) of cement into the formation.

Jan 1, 1985

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By R. H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing some practical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers? exposure to airborne contaminants.

Jan 1, 2008

By Adrian C. Dorenfeld

[Agitation and transport of slurries have been investigated intensively for the past twenty years. It has been shown (1) that slurries have the properties summarized in Figs. 1, 2, 3, 4, and S. For a detailed exposition the reader is referred to the above reference and the bibliography, which, in turn, have extensive references and bibliographies. An interesting problem with which the senior author has been concerned with is the scab up of power requirements for slurry agitators operating in the laminar region with pseudo plastic materials. Pulps of shaly ores, after various chemical reactions in aqueous leaching systems, are often difficult to settle and filter if agitation is violent. In these cases agitation must be at a minimum, yet prevent [tling] such as in copper uranium ores. This mild agitation is on the laminar region.]

Jan 1, 1967

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979