Search Documents

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By Mark J. Dowiak, Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980s. About 45 Mt of hazardous wastes are produced yearly. One major aspect of the problem is the siting, design, and construction of' environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sites for several reasons. • Surface mines offer an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic, savings when compared with sites on undisturbed lands that might require extensive excavation or embankment construction. • Surface mines often have an abundance of mine spoil available that could potentially serve as construction material. This could result in a significant economic advantage over other sites that might require extensive amounts of construction material to be excavated or hauled in. • Operation of a commercial disposal facility in a surface mine can reduce or totally alleviate reclamation costs. • For an abandoned surface mine, conversion into a disposal facility could represent a positive form of land use and may provide a means for reclaiming lands that would otherwise remain unreclaimed. Despite these positive reasons, there are many technical factors associated with surface raining that can make the prospect of disposal site development an uncertain one. Before discussing factors associated with mining that can present siting, design, or construction problems, some understanding of the basic components of a chemical waste disposal facility is necessary.

Jan 2, 1981

By L. Cui

X. Huang (1997) recently suggested a poroelastic model for simulating the hydraulic fracturing breakdown pressure. His paper began with a discussion questioning Haimson and Fairhurst's (H&F) model. He claimed that the H&F model failed to lead to the Hubbert and Willis (H&W) model as[ a --> 0.] Huang also tried to explain why the H&F model could only work for special types of rock conditions. He pointed out that one possible reason could be that the Terzaghi's effective-stress concept had been adopted. The H&F model (Haimson and Fairhurst, 1969) was derived under the conditions that the borehole wall is fully penetrated (pp = pi) and a drained state is realized (steady pore-pressure field). Cui et al. (1997a) demonstrated that, under drained conditions, the total stresses in the penetrating poroelastic model (identical to the H&F model) degenerate into their counterparts in the elastic model (identical to the H&W model) as [a -- 0.] However, the effective-stress conditions are different for both of these models, because different pore-pressure conditions at the borehole wall were adopted. In the H&W model, p = po was assumed, i.e., the pore pressure field is not disturbed; but pp = pi was assumed in the H&F model. Assuming that Terzaghi's effective-stress controls tensile failure (that was the hypothesis adopted in both the H&F and the H&W models), only the following two special drained poroelastic cases may degenerate into the H&W model for very small a: • when the pore pressure at the borehole wall remains at the same level as the virgin pore pressure for a penetrating model and when the borehole wall is simply impermeable (i.e., the nonpenetrating model, Cui et al., 1997b). Therefore, simply setting a = 0 in the H&F model generally does not lead to the same problem described by the H&W model. On the other hand, when the porepressure boundary conditions do not correspond to the ones in the H&W model, a degeneration of the poroelastic model to the H&W model as [a – 0] should be questionable. The pore pressure at the borehole wall is generally dependent on the injection-fluid pressure and the penetrating conditions at the borehole wall, such as the existence of a filter-cake. For an impermeable wall, pp is independent of Pi, and it is basically an unknown [(how¬ever, pp -- po as t --oo).] For a fully permeable wall, pp is the same as Pi. Between these two extremes, pp should be a function of p; and the permeable condition of the borehole wall, which may be dependent of the leak-off coefficient cf. (the range of cf is from 0 to 1). Theoretically, for a rock with low permeability, a penetrating borehole wall is still possible. For saturated porous materials with very low values of a, poroelasticity shows that a pore pressure will be built up due to the stress concentration subjected to a nonhydrostatic in situ stress field (Cheng et al., 1993). This phenomenon is known as the Skempton effect. The variation of the pore pressure may be evaluated by [AP = 3 B(A rr + 06ee + A (Y,,)] (1) where B is the Skempton pore pressure coefficient. This pore pressure variation dissipates as time increases (it is totally gone as the drained state is approached). The rate of the dissipation mainly rely on the permeability of the formation. The dissipation is very slow for tight formations because their permeability is very low, and it is fast for rocks of high permeability. According to our analyses, the time period for this process could be from seconds (for sandstone's) to a couple of days (for stales). One possible reason that the H&C model did not agree well with the experimental results for rocks with low permeability might be that the time interval between the application of the loading and the fluid injection had not been long enough for the dissipation of the Skempton effect. The effective-stress law basically defines how much pore pressure contributes to the total stress. The difference between Terzaghi's effective stress and Biot's effective stress is that 100% of the pore pressure contributes to the total stress in Terzaghi's definition, while only a certain portion of the pore pressure ((ap) goes to the total stress in Biot's definition. Therefore, when the pore pressure at the boretole wall (pp) is determined according to Biot's effective-stress law, app in the total tangential stress is attributed to the pore pressure. In other words, Terzaghi's effective tangential stress is expressed

Jan 1, 1999

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By M. J. Zdunczyk

Sand is one of the most common materials on the earth’s surface. It is a naturally occurring material resulting from the physical and chemical breakdown of rocks. The definition of sand varies, as do the number of products made from the material. Sand is generally classified by grain size, however the measurement or scales differ depending on the context in which it is being used. Geologist define sand as particles of rock between .05 and 2 millimeters in diameter. The variability of the mineral composition generally dictates which sand can be used for different industrial purposes. For example, sand used for Portland cement concrete and asphaltic concrete mixtures can be very different in physical and chemical composition than sand used in the making of fiberglass. In this paper, construction uses of silica sand, which consists almost entirely of the mineral quartz (SiO2), will be discussed and analyzed.

Jan 1, 2001

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By John A. Shuster

INTRODUCTION Controlled ground freezing for mining and construction applications has been in use for over a century. Despite the great technological evolution which has occurred during this period, ground freezing is still used on projects today with much the same basic technology as that used originally over 100 years ago. Major developments have occurred in the separate fields of frozen soil mechanics, refrigeration, and heat transfer analysis. However, except for a few projects in Europe and Asia, these developments have not been combined to upgrade ground freezing techniques to their potential level. In view of this situation, it is believed desirable to examine the art of ground freezing in light of recent technical developments, together with highlights on some of the apparent advantages, disadvantages and economics of the various alternative approaches. The purpose of this paper is to attempt such an examination, with particular emphasis on the practical application of presently available technology. GENERAL ADVANTAGES AND DISADVANTAGES Ground freezing may be used in any soil or rock formation, regardless of structure, grain size or permeability; however, it is best suited to soft ground rather than rock conditions. Freezing may be used for any size, shape or depth of excavation and the same physical plant can be used from job to job despite wide variation in these factors.

Jan 1, 1997

By D. C. Yang, J. Ye

A comprehensive flotation study has been conducted on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University (MTU). The results are compared with those for a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4% to 5% higher recovery and much lower silica impurity than the concentrate produced by up to six stages using a conventional mechanical cell. The results also show that the packed-column flotation process is particularly suitable for the recovery of finer fluorspar particles.

Jan 1, 1993

By Rudolf E. Greuer, Xintan Chang

Mine fires have always been of great concern to mining engineers and their behavior has been studied for a long time. Although an abundance of observations exist, no satisfactory mathematical model for their interpretation and extrapolation has become known. The paper presented here tries to close this gap, making use of the laws of chemical kinetics, energy and momentum conservation. To overcome the mathematical difficulties, the fire zone is axially divided into segments and radially into sections, each one with an extension of only a few inches. Conditions in segments and sections are updated in time intervals of one second or less. To solve the large number of resulting equations, a numerical solution is performed. The model has so far been tried on timber fires. It confirms experimental observations on the ignition phases and equilibria of these fires.

Jan 1, 1987

By J. Wiedenroth

Since the end of the 1970s Pipe Conveyors have become increasingly important for conveying bulk materials because they have some specific advantages over conventional troughed belt conveyors. FLSmidth KOCH Pipe Conveyor represent the marked-leading know how of the former KOCH Transporttechnik GmbH, which belongs to the FLSmidth Group since January 2007. Pipe Conveyors from FLSmidth KOCH are already being used successfully at more than 260 locations around the world. Their special properties, their extreme flexibility, the horizontal and vertical changes in direction without transfer points, the small space requirement, the low-noise running and their optimum protection of environment and material without any additional casing mean that Pipe Conveyors can provide transport solutions that are often far superior to other conveying systems. The utilization of these many advantages will be illustrated in the following example of the world?s longest Pipe Conveyor at Cementos Lima, the Peruvian cement producer.

Jan 1, 2010

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By Sigmund J. Sulinski

The following is a progress report on a continuing study being made by the Sanitary District for purposes of developing reliable data for predicting costs and progress on future tunnel contracts. All data available to date on five separate tunnel contracts has been analyzed. All were machine-mined in soft ground, all used steel ribs and wood lagging and finished inside diameters varying from 5'6" to 6'6". Basic data regarding progress per shift, hours mined per shift, hours of downtime per shift, cause of downtime and type of soil mined were reported by the District's resident engineer at the job site. Figure 1, Weekly Mining Report is an example of the form used. Data regarding manpower and equipment used during tunnelling operations was also supplied by the resident engineer during the course of construction. Soil type being mined was verified by the resident engineer during construction, by visual observation, and compared with data listed on a previously prepared soil profile. The soil profile is a graphic presentation of anticipated soil stratas superimposed on a cross section

Jan 1, 1997

By David J. Starbuck

For small precious metals mining to show a comeback a different perspective must be taken than that of larger mining companies. This perspective must be much the same as that of past successful smaller mining enterprises such as when the US had a need for Uranium. Abandoned mines and environmental concerns in older mining districts have discouraged many from entering with the attitudes of why try there if so many unsuccessful mines exist. A small mining venture can be successful there but must have a "think smart'' attitude. There must be a thorough understanding of deposits, utilization of advanced technology and a properly managed mining operation. "THINK SMART" MINING The small mine operator is usually looking for small high grade deposits, consequently, long term success depends on a series of small successful mining operations. The small miner must succeed right-off or credibility and future project funding will suffer. No veteran of even a few years in the mining industry needs to be told that a dollar spent on production today fails to yield as much as it once did. More efficient equipment and techniques have helped soften the problem, but there is little likelihood that a mining company can do much to control inflation, wages, regulations, or grade. That leaves the small miner to "think smart" as one area where operating dollars can still be stretched to produce more than they presently do (Gardner. 1981). In the planning stage of a mining venture, when most options are still open, the main controllable elements are market timing, deposit selection, cutoff grade, mining method, mine design, mining sequence, rate of production build up, process design, project financing structure, project management, and project ownership structure. During planning, optimum criteria can be established for each of these. Once a mine is in production, these options are foreclosed or at least severely constrained. The more thought given to a mining program using all information available the less the risk of encountering disabling surprises. Thus the intent of this paper is to suggest the "think smart" attitude most small mine operations use for long term success. If one looks at a number of successful mining ventures, whether large or small, there is a general logic most have followed to be successful. They have used proven exploration, mining and processing techniques along with economic evaluation and experienced personnel to improve their odds. LOGIC IN DEVELOPING A FEASIBLE VENTURE Most successful small mine ventures achieve positive cash flow as quickly as possible by seeking out those deposits which require the least time and expense on activities leading up to production. To do this they look for deposits that are the most accessible, easily investigated, mined and processed with the cheapest fundamental methods. The general sequence of events starting with district selection are deposit selection, preliminary feasibility, exploration, detailed economic feasibility, mine planning, development and production. Each successive step becomes more costly requiring intermediate decisions along the way. District Selection Small operations should look for known deposits which favor the occurrence of the type deposit sought rather than efforts in unproductive areas. Known deposits in developed areas have some advantages over remote areas: 1. More alternative methods of transportation are available. 2. A larger stable work force is available. 3. The area is usually more pro-mining. 4. Power, water, housing, technical services, skilled services, schools, recreation and shopping are available.

Jan 1, 1987

A roof rating system has been devel¬oped for upper seam damage prediction during mul¬ti-seam mining based on structural and geologic conditions in the upper seam. Two primary consid¬erations -geologic and spatial - form the basis of the classification system. It includes factors commonly found in geomechanics classification systems as well as factors which are peculiar to multi-seam mining, such as those which define the two adjacent seams and the innerburden. This rating system has been applied to numerous case studies to form empirical relationships for quan-titatively predicting potential upper seam damage based on anticipated subsidence and strain values and vertical movements.

Jan 1, 1988

By Surendra K. Mishra

Recent land ban act has put pressure on industry to decontaminate the waste streams before they could be discharged. However, for both metal and organic contaminated wastes, there are commercial incentives to recover usable resources. Recent technology developments have helped meeting such objectives. This paper reviews developments in treatment technologies for industrial wastes. Major chemical groups used in waste treatment are summarized.

Jan 1, 1994

By Dennis C. Martin

Assessment of the potential for mining induced subsidence and determination of ultimate design requirements for a mining operation should be based on a number of assessment approaches. Although the rock mechanics engineer has a variety of limit equilibrium and numerical modeling tools available for assessment and prediction of subsidence effects, empirical approaches based on precedent experience provide a powerful tool for calibration/verification of analytical models and prediction of subsidence. Three separate analyses approaches have been applied to the assessment of potential subsidence for a proposed block caving mine in eastern Canada. The investigations have included an assessment of documented historical information from previous block cave mining at the site, deterministic analyses using limit equilibrium approaches to assess kinematically possible failure mechanisms, and three-dimensional numerical modeling techniques. Analyses results have been used and compared with precedent experience and documentation of subsidence behavior from previous mining to optimize the subsidence predictions for the proposed mine.

Jan 1, 1998

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By William H. Lehr

A 4200 ton-per- hour marine transfer terminal, where river and oceangoing vessels simultaneously exchange cargos of coal and phosphate rock, is now in operation near the mouth of the Mississippi. Its materials handling machinery includes a bucket ladder barge unloader; a rope operated clamshell bucket unloader; a coal loader; and a rail mounted bucket wheel machine. The design and operation of this equipment is described as are the docks and conveying, breasting and barge-haul systems in use at the facility. Design considerations imposed by soil and river conditions, geography, operating needs and investment requirements are discussed. The economic significance of design and shipping innovations introduced by this facility is noted.

Jan 1, 1967

By D. L. Misterek, E. J. Slebir, G. W. Ring, M. A. Laird

INTRODUCTION In 1973, the Federal Highway Administration (FHWA) initiated a 10-year program of research on tunneling technology for future highways as a part of a larger Department of Transportation effort on tunnels. The objectives of the FHWA program are to: improve tunnel design technology, reduce costs, minimize adverse environmental impact due to construction, increase the rate of construction, and assure the maintenance of a safe and attractive tunnel environment. The program is divided into four research tasks designed to solve tunneling problems identified by the engineering and field offices of the FHWA. These tasks are as follows: 1. Cut-and-Cover Tunneling 2. Site Investigations 3. Ground Movements - Prediction and Control 4. Highway Environmental Criteria for Tunnels In order to provide input into Tasks 2 and 3, the FHWA is sponsoring an investigation and testing program by the U.S. Bureau of Reclamation to instrument and monitor two sites in the second bore of the Eisenhower Memorial Tunnel located on Interstate Highway 70 at Loveland Pass approximately 97 km (60 miles) west of Denver, Colorado. The tunnel will be approximately 14.0 m (46 ft) in diameter when excavated. The study is designed to generate data on: (1) changes in the state of stress, and movements during and after tunneling, (2) tunnel lining design requirements, (3) developing a

Jan 1, 1976