Search Documents

By Yi Luo, Jianwei Cheng, Mingming Li, Lei Xiao

Concealed thermal events in longwall gobs present safety hazards for underground coal miners and can significantly interrupt mining production. The probable causes for such thermal events range from coal oxidation at slightly above ambient temperature to smoldering fires due to spontaneous combustion of the broken coal left in the gobs. Locating such “hot spots” is the key step for planning and implementing mitigation measures to bring such thermal events under control. If a mine section, or even an entire mine, has to be sealed, understanding the status of the sealed mine atmosphere is important for the decisions guiding subsequent actions. The gas composition data obtained through the tube bundle mine atmospheric monitoring system is firsthand information of great value. Fire ratios proposed by various researchers and derived from gas composition data are useful in determining the fire status and even approximating the source locations (Timko and Derick, 2006). However, the applicability of each of these ratios under particular conditions should be carefully evaluated. The use of properly combined fire ratios can enhance the certainty of analysis. The explosibility of a sealed mine atmosphere deserves primary concern for safety reasons during seal construction, idle time and reopening of the sealed area.Mine atmospheric monitoring data from a longwall mine with flame fire have been analyzed. Efforts have been made to identify the possible causes, locations and statuses of these events using the obtained gas data, as well as other ventilation, geological and mining parameters. The effect of injected inert gas to control the events has also been quantified. The explosibility of the sealed atmosphere has been determined using two methods.

Jan 1, 2012

By J. P. Rider, T. W. Beck, J. A. Organiscak

"The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR) has recently developed a series of models utilizing Computational Fluid Dynamics (CFD) to study gas distribution around a continuous mining machine with various fan-powered flooded bed scrubber discharge configurations. CFD models utilizing Species Transport Model without reactions in FLUENT were constructed to evaluate the redirection of scrubber discharge toward the mining face rather than behind the return curtain. The following scenarios are considered in this study: 100% of the discharge redirected back towards the face on the off-curtain side of the continuous miner; 100% of the discharge redirected back towards the face, but divided equally to both sides of the machine; and 15% of the discharge redirected toward the face on the off-curtain side of the machine, with 85% directed into the return. These models were compared to a model with a conventional scrubber discharge where air is directed away from the face into the return. The CFD models were calibrated and validated based on experimental data and accurately predicted sulfur hexafluoride (SF6) gas levels at four gas monitoring locations. One additional prediction model was simulated to consider a different scrubber discharge angle for the 100% redirected, equally divided case. These models identified relatively high gassy areas around the continuous miner which may not warrant their use in coal mines with medium to high methane liberation rates. This paper describes the methodology used to develop the CFD models, and the validation of the models based on experimental data.INTRODUCTION Methane gas and respirable dust are two hazards frequently encountered at continuous miner (CM) operations. An accumulation of both methane gas and coal dust may lead to massive explosions underground [1], and overexposure to respirable coal dust can result in pneumoconiosis (commonly referred to as “Black Lung Disease”) in coal workers [2]. Current U.S. federal coal mine regulations limit concentrations of methane gas to below 1% at the face area and require exposures to respirable coal dust to be at or less than 2.0 mg/m3 for an 8 h shift average. Begin on August 1, 2016; the overall respirable dust standard in coal mines is reduced from 2.0 to 1.5 mg/m3 for full shift sampling. If the quartz content of the dust exceeds 5% by weight, the dust standard becomes more stringent, reducing the allowable concentration to the value of 10 divided by the % quartz."

Jan 1, 2015

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

The purpose of this paper is to demonstrate how the Computational Fluid Dynamics (CFD) technique can be an attractive approach to evaluate the performance of face ventilation systems. To present the capability of the CFD for such a study and for design purposes, a series of simulations using CFD have been performed at the Department of Mining Engineering, University of Kentucky, for different face ventilation arrangements (e.g. different scrubber geometries, brattice (curtain) and continuous miners locations, airflow quantities, etc.). Results from these simulations are displayed as three dimensional graphs and discussed. Needs for the field validation of these results and refinements of design methodologies are also discussed.

Jan 1, 1998

By William J. Miles

For compliance with the Hazard Communication Standard and other federal and state regulations, numerous minerals, chemicals and products need to be evaluated for crystalline silica content at a threshold of 0.1 %. The polymorphs of crystalline silica that can occur in chemical and mineral products are quartz, cristobalite and tridymite. Other natural, industrial and synthetic amorphous silicas and hydrates must be distinguished from these polymorphs to prevent over-regulation in the workplace and environment. A number of industrial silica products are composed of glasses, expanded perlite, diatomite, slags, and precipitated and fumed silica products. Amorphous silica hydrates used for industrial products, include opal (hydrated silica of biogenic or inorganic origin), perlite, pumice and tuffs. In addition, crystalline and amorphous silicate minerals and chemicals, abundant in nature and industrial products, must be distinguished from the polymorphs of crystalline silica.

Jan 1, 1997

By H. Nakazawa

Galvanic contact, occurring between electricall y conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions, and the results were correlated with their oxygen-consuming characteristics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, x-ray photoelectron spectroscopy and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased whereas that on pyrite increased when these minerals were held in contact. An electrochemical mechanism was proposed for the observed behaviors.

Jan 1, 1985

By B. G. McNish

Neutron Activator Laboratory Analyzer used for Rapid Analysis for Ore Blending, Stripping, and Mine Control BAUXITE is a rock and not a mineral. Since it is a rock, its mineral content varies depending upon the parent material, the topographic location of the deposit and the severity of the weathering and oxidation processes which produced it. At Bauxite, Arkansas the major mineralogical constituent of the bauxite is gibbsite with ~IL- purities of silica, iron oxide, and titania minerals. Minor amounts of other minerals are found. Chemical composition varies from 45% to 60% alumina, 5% to 25% silica, 1% to 15% ferric oxide, and 1% to 3% titania. The Arkansas bauxite region is located entirely within the north- central area of the West Gulf Coastal Plain near the northwestern boundary with the Interior Highlands. The region trends northeast-southwest and is about 42 kilometers long. It is divided into two districts; one in Saline County and the other in Pulaski County. The Saline District is the most important since it has produced most of the bauxite. This district is located at Bauxite, Arkansas and the deposits are found around the flanks of the Saline Dome. It is roughly square-shaped and is about 190 square kilometers in area. The source rock for the deposits is a Late Cretaceous, grey, nepheline syenite.

Jan 1, 1979

By Richard C. Holmquist

Some of you may be old enough to remember -- as I do -- the early days of World War II. A highly prepared, well-equipped Japanese striking force had moved like lightning across the South Pacific islands and Southeastern Asia. As the invasion force pushed its way down the Malaysian Peninsula, Singapore stood serene and beautiful, protected by its natural moat of water, busy as ever with its commercial pursuits. One can see its captains of trade and industry now, sitting com¬fortably on the veranda of the "Singapore Country Club", sipping scotch between cricket games, convinced that the weary, logistically extended Japanese force couldn't possibly cross over to their island which had been so secure for a hundred' years or more. No need to remind you what happened. The brave men in their ships at sea and in the gun emplacements ashore were hopelessly out-gunned and out-maneuvered.

Jan 1, 1979

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By K. J. Shelswell

This work describes the design, analysis, and comparison of discrete simulation and static spreadsheet models developed to compare the oreflow efficiency of two conveyor-based material handling systems; one approach with a conveyor stream in series and one with parallel conveyor streams. Analysis and comparison indicated that daily rates were significantly affected by random conveyor failures in both designs. The compound effect of random failures limited the effectiveness of long belt assemblies in series, while the parallel conveyor stream design partially alleviated this constraint. The static spreadsheet model predicted a lower average daily oreflow rate for the series conveyor stream design and a higher average daily oreflow rate for the design with parallel conveyor streams when compared to the discrete simulation results. These discrepancies were the product of model sensitivity to operational factors incorporated in the system and provided the opportunity to further use the discrete simulation models for trade-off comparisons and sensitivity breakdowns of mine operating practices and material handling system efficiencies in both the series and parallel belt stream designs

Feb 23, 2014

By Douglas M. Deason

Swelling clays, such as montmorillonite, contribute significantly to the poor dewatering and consolidation behavior of the Florida phosphate clay wastes. Understanding and to a degree, control of the forces which cause the swelling behavior may aid in supplying a solution to this problem. The technical feasibility of utilizing control- led dispersion for aiding dewatering of phosphatic slimes was investigated. This technique is based upon inhibition of swelling and self-dispersing tendencies of the montmorillonite clays by dispersing the solids in electrolyte solutions. Through this process, significant improvements in settling rates and sediment solids content were achieved in both pure clay systems and on simulated phosphate slimes.

Jan 1, 1983

By Robert M. Dreyer

Thirty years ago it was possible to locate a quarry site for crushed rock for concrete aggregate by finding the nearest solid rock bluff accessible by road, But times have changed and the location of a quarry site to furnish crushed rock for concrete aggregate now has become rather complicated, Although both sand and gravel can be used for aggregate, this discussion will be confined to crushed rock in the regions around a metropolitan area. Let us assume that a consultant has been retained to advise on the desirability, and the possibility, of opening a new quarry within a given area. The problems are geological and ecological. Since the geological problems are simpler, they will be discussed first. Generally, the first step is to make a market study of competitive aggregate sources within the projected area. Assuming that the quality of aggregate to be sold by competitors as well as their mining costs will, within narrow limits, be the same, the problem becomes essentially a study of haulage costs from established quarries into the projected new area. Since haulage cannot be effected along straight lines and since each quarry operator may have different unit haulage costs, a map showing lines of increasing cost intersecting points on roads available for truck haulage radiating from competitive quarries can be rather complicated. Such a map, more-over, changes each time a new haulage contract is negotiated by a

Jan 1, 1971

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974

By K. McG. Bowling

A statistically-designed exper¬mental study showed how gangue minerals, flux additions, fineness of grind, firing temperature and time affect the properties of acid pellets made from a Western Australian hematite ore. Alumina has less effect than silica and lime, but various interactions between the six variables occur, which influence abrasion index, reducibility and cold compression strength. Finer grinding has little influence on reducibility but improves the other two properties. The major variable is firing temperature. It interacts with all other variables in its effects on pellet properties. Calculations based on the data show the implications for straight-grate pellet plants and optimum hood temperature range.

Jan 1, 1980

By Walid M. Abdellah, Soliman Abu Elatta A. Mahmoud, Hanaa A. Abu Khoziem

The high-grade Th-U-Y zone is one of the numerous mineralized zones found in the El Garra El Hamra hydrothermally altered syenites in southwestern Egypt. It is characterized by the thorium minerals thorite and thorogummite, which are closely associated with xenotime-(Y). This zone of mineralization is localized in the eastern part of the El Garra El Hamra hydrothermally altered syenites. This zone does not relate to the first phase of syenites that appeared on the surface but is linked to the other, hidden phase of the syenitic body. Additionally, the fluids responsible for the mineralization of this zone belong to the late-stage hydrothermal event as well as the fault action due to the fact that it had continued reactivations for a long period of time. The studied mineralized zone also contains ceriopyrochlore-(Ce),(Ce,Ca,)2 (Nb,Ta)2O6 (OH), fluorite (CaF2) and barite (BaSO4), which are found in considerable amounts, whereas apatite (Ca5(PO4)3F) and chromite (FeCr2O4) are rarely found together with Fe-oxi-hydroxides (hematite and goethite) with a minor amount of jarosite (KFe33+(OH)6(SO4)2). Finally, the main constituent mineral in the zone is the pseudomorph perthite in addition to quartz, which is found as deformed crystals. A technological sample was collected from this zone and was found to assay 4.62 weight percent thorium (Th), 0.37 weight percent uranium (U) and 3.12 weight percent rare earth elements (REEs). From the chemical and mineralogical composition of the studied technological sample, the leachabilities of Th, U and REEs were investigated using sulfuric acid (H2SO4) agitation leaching and pug leaching methods. The latter was found to be preferred under the conditions of 0.54 ton H2SO4 per ton of altered syenite at 110 °C for two hours.

By C. J. Bise, P. Bucks

Central Appalachian coal reserves are a valuable natural resource in high demand, both domestically and internationally, justifying efforts to increase percentage recovery through pillaring. Unfortunately, the challenge associated with pillar extraction introduces additional safety risks during the activity. Although pillaring developed prior to mechanized mining, current technology and mining practices have made this form of mining highly modernized. However, current fatality trends suggest that work still needs to be done to control the residual risk that is not controlled by modern practices, such as those having a personnel-performance-based component. This paper investigates the application of modern coal pillaring techniques and will present a risk-management-based strategy that targets personnel-performance-based risk, in order to improve the ability of safety engineers, managers and trainers to provide training programs addressing the needs of pillaring sections.

Jan 1, 2012

By Y. C. Kim

Using an exhaustive data set of Walker Lake, four different kriging techniques plus the inverse distance squared weighting were compared with regards to each one's performance in accurately estimating the block grades. The North-West quadrant of the Walker Lake data area was used because of its extreme variability of values and its distinct contour of the values. There were 1900 exhaustive data points in the selected area from which a total of 121 samples were drawn following the sampling strategy given in Isaaks and Srivastava (1989). The average of 5 x 5 exhaustive data points was treated as the true, known block grade. A total of 780 blocks, each block corresponding to the average of 5x5 exhaustive data points, were then estimated using the 121 sample points. The resulting estimates were then compared with the true known values to determine each technique's prediction performance. For this particular portion of the Walker Lake and for the given sampling strategies used, the obtained results for the global estimation are mixed. For the variable U which is much more variable, the rankings are; 1) Jackknife Kriging (JK), 2) Indicator Kriging (IK), 3) Inverse Distance Square weighting (IDS), 4) Ordinary Kriging (OK), and 5) Log-Jackknife Kriging (LJK). For the variable V, the results are; 1) OK, 2) IK, 3) JK, 4) LJK, and 5) IDS. When we apply several cutoff grades to the estimates to determine the conditional mean grades and tonnage, the above rankings generally get shifted around. Two exceptions to these cases are; a) UK for U and b) IDS for V. These two consistently ranked at the bottom.

Jan 1, 1995

By N. Kuyucak

Uranium ores leached with sulphuric acid typically have poor dewatering properties. Applicability of controlled neutralization where gypsum precipitates as crystalline particles, improving dewatering properties of material was examined. Neutralized material was then dewatered using paste thickener to increase underflow density. The objectives are to maximize water recovery due to water scarcity and to produce suitable cemented paste fill material for optimizing underground ore recovery. Work was performed on acidic slurry samples collected after leaching but before the resin-in-pulp uranium recovery. Controlled neutralization greatly reduced volume of neutralization precipitates giving higher densities and improving the dewatering (filtration) properties. As a result it would be possible to increase the water recycled to the mill. Another benefit is that sulphate in the recycled water was reduced to saturation limit minimizing scaling of process equipment. Additional test work is needed; however, Unconfined Compressive Strength results imply that controlled neutralization increases the strength of paste fill and possibly offers opportunities towards a viable backfill option.

Jan 1, 2010

By Caroline Gerwig, Joseph R. Wickline, Zach Agioutantis

In longwall mining, the progressive caving of the roof allows stored energy to dissipate over an extended time. However, in some cases, the roof strata above the longwall panel are unusually strong and do not break with the movement of the working face. Instead, the roof material bridges over the expanse of the longwall, forming an unstable beam. Later, when this beam breaks, the stored energy can release suddenly, causing a seismic event to propagate to surrounding mine workings. The focus of this paper is to estimate the size of beams that form over longwall panels to the seismic energy recorded by the mine. Analytical calculations are used to verify two-dimensional models of longwall roof beams to determine the strain energy and gravitational energy developed, which is then released upon strata failure to surrounding mine workings. Models are developed using RS2 to model the stress, strain, and deflection along the bottom of the longwall roof beam to calculate gravitational and strain energies. Gravitational energy is shown to be the main driving factor in energy release, except for the beams with low heights. Analyses allow the determination of beam characteristics based on seismic data. The analysis is refined using swelling factor to compare various beam drop heights. The models show an increase in seismic magnitude for higher drop heights. However, the actual data provided by the Buchanan mine displays a decrease in seismic magnitude with increasing drop height, indicating that energy is dissipated into the broken gob material as drop height increases.

Jul 1, 2023