Search Documents

By Myles G. Hyams

A mining project is proposed for the state of Pahang, Malaysia. The proposal involves the mining of a sulphidic ore body and initial processing to form a sulphide concentrate which will be transported to a roaster/acid plant for the production of sulphuric acid. An outline is presented on the potential environmental impacts of the project which have been assessed by superimposing project infrastructure and processes on to the physical, biological and social environment during the early design and planning stage of the project. The potential impacts eliminated by engineering design and the techniques employed are presented. However, there are a number of potential impacts that require careful consideration and planning for long term management. These include surface water drainage, waste rock leachate, tailings disposal and the social environment. Environmental management designed to minimise or alleviate these impacts as a result of project implementation concludes the paper.

Jan 1, 1991

By E. A. Sondreal

Requirements of flue gas desulfurization (FGD) for Eastern and Western U.S. coals will not be the same because of differences in coal sulfur content, ash analysis, and beating value. The effects of these differences and of limited availability of water in the West are the subjects of this paper. Eastern and Central bituminous coals are generally high in sulfur and require removal efficiencies in the range of 70 to 90 percent to meet the Federal emission standard of 1.2 lb SO2/MMBtu. Ash in Eastern coals is low in alkali content and is relatively insoluble in scrubber solutions. High sulfur content and market availability make salable product methods more attractive in the fast and Central United States than in the West. Western subbituminous coals and lignites are generally low in sulfur content, however, only a few deposits could reliably meet the Federal emission standard without FGD, Required removal efficiencies generally fall in the range of 0 to 60 percent to meet the 1.2 lb SO2/MMBtu limit. If the standard were raised to 2 lb S02/MMBtu, approximately two-thirds of Western coals could be burned without FGD. Some Western coals contain ash high in alkali, some of which is soluble in scrubber solutions. This complicates scrubber chemistry, but it also provides the meant for displacing some or all of the limestone requirements when only moderate S02 removal is required. Dry areas in the West would benefit from full commercial developement of dry processes of FGD.

Jan 1, 1974

By Roy A. Grancher

?The Horn of Plenty seems to have sprung a leak?.? anonymous For the first time in the Nation's peace-time history, shortages have become a way of life for the United States. Such words as scarce, tight, and critical are used in regard to supply, leading to priorities, allocations, and possible rationing as make-shift attempts to satisfy demand. Almost every day a new type of shortage appears in another product area that has traditionally been taken for granted as being in perpetual abundance. The range of coverage extends from basic commodities such as oil, chemicals, cement, steel, copper, cotton, etc., through to machine tools, motors, bearings, electronic components, etc. , to those finished outputs that satisfy our fundamental requirements for food, clothing and shelter. Signs of the times appear in cancelled airline flights, unfilled lines at gasoline stations, no available home freezers, lengthy delays in any furniture deliveries, or to that little old lady seen walking out of a local supermarket clutching her hoard of twenty rolls of toilet paper. What a sad commentary to have to make about our Land of Plenty, so long the envy of the World for its material wealth -- and today with its initials "U. S." seemingly standing for ?Unlimited Shortages.?

Jan 1, 1974

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By M. G. Rylatt

The Ekati process plant flowsheet features the common steps in diamond recovery plant design. Primary treatment and concentration is by crushing, scrubbing, high-pressure grinding rolls and heavy medium separation (Fig. 1). Secondary concentration is by an attrition mill; wet, high-intensity magnetic separation and X-ray sorting (Fig. 2). All of these are performed on site, although final sorting of the diamonds into commercial categories will be carried out elsewhere. The initial throughput rate is 9 kt/d (9,900 stpd), increasing to 18 kt/d (20,000 stpd) during the first 10 years of operation. A range of ore characteristics will be encountered that will effect the plant operating conditions during the life of the mine. The adopted design envelope is based on these expected variations. The design is based on the use of large-scale equipment, incorporating the latest and most efficient technology available. Where proven technology exists, no attempt was made to reinvent the wheel. However, where recently developed technology offers a significant advantage, this has been incorporated into the design. The Ekati run-of-mine (ROM) and coarse ore handling facilities are unheated, to take advantage of the better handling characteristics of the frozen ore in winter. The stockpile reclaim features an MMD mineral sizer (a toothed roll crusher) to minimize the problems of handling thawed, sticky kimberlite in the summer and break frozen lumps in the winter. All processing downstream from primary crushing and the coarse ore stockpile is carried out in a temperature-controlled environment in the main process plant building. Personnel involvement in the process is mini¬mized by using a Modicon Quantum series PLC with human-machine-interfaces (HMI) running Wonder-ware software on dedicated personal computers.

Jan 1, 1999

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Z. Hajnal

Three years ago a research program was initiated at the University of Saskatchewan to develop seismic surveying techniques for use in the Precambrian geological environment. The success of the reflection method in many younger geological settings suggested that this is the technique which would be the most suitable for experimentation. A successful adaptation of this technique to the Shield environment would make mapping of rock formations possible to much greater depth than is possible at the present time with any other applied geophysical technique. This presentation attempts to illustrate the advances which have been made in this program and will provide some insight into future plans. The field investigations were limited to the Flin Flon basin near to the town of Flin Flon, Manitoba (Fig. 1). This area was chosen because the surface geology has been mapped in great detail and it is a very important base metal producing region. It is an ancient sedimentary basin with some characteristics similar to areas where the reflection method has been successful.

Jan 1, 1976

By J. A. Herbst

It is widely recognized that Semiautogenous Grinding (SAG) circuits require the use of effective process control techniques to achieve their full processing potential and to protect them from the harmful effects of overloads and grind-outs. This requirement is even more essential as the variability of the ore being processed increases. The new Chino Mines Company concentrator located near Santa Rita, New Mexico started operation in June of 1982. At least eight major rock types are mined and milled. Ore hardness, feed size, and specific gravity are quite variable. Typical feed rates per grinding line are 850-900 tph but extremes of 260-1200 tph have been encountered. Normal feed rate variations of between 400 and 1100 tph are encountered on a weekly and sometimes daily basis. Feed size varies with rock type from a maximum of eight inches for the harder ores to two inches for the softer ores. One somewhat unique characteristic of the Santa Rita ore body among major copper mines is the wide variation in ore specific gravity. Specific gravities of the major rock types range between 2.7 and 3.6. The specific gravity variations are due to large changes in magnetite concentration throughout the pit. The result of this is large variations in SAG mill throughput which can have a harmful effect on downstream ball milling and flotation performance. Due to these wide fluctuations in ore characteristics, it was recognized soon after startup that successful operation of the grinding circuit and the plant at large was dependent upon the development of an effective automatic grinding control strategy. Research at the University of Utah has suggested that control based upon critical but difficult or costly to measure variables would improve automatic control performance. A project team made up of the Chino process control staff, Kennecott's Process Control department and the University of Utah Metallurgy Department was established to assess these concepts at Chino. This paper describes the development and on-line plant implementation of an Extended Kalman Filter that uses simple models of the SAG milling process, to predict the volumetric loading, the rock mass, the water mass, and the ball mass within the SAG mills at Chino. The on-line estimation of these parameters is the first step in the development of an integrated SAG mill/ball mill control strategy which is hoped to L eventually maintain the grinding circuit at its maximum capacity, while balancing the grinding load between the SAG and ball mills. Examples of long term estimation with the models and filter are shown for typical operating conditions as well as a SAG mill overload and grind-out.

Jan 1, 1983

By P. D. Pattillo, J. B. Cheatham, Y. -H. Lin

The stability of a hemispherical cavity, intended to model a perforation opening in the vicinity of a borehole, is analyzed for the case of poroelastic-plastic material behavior. Two plasticity models of differing complexity are considered, with the emphasis in either model being the use of strain softening to calculate inelastic stiffness. Sample results illustrate the effect of steady fluid flow on the response, and possible collapse, of the near perforation region.

Jan 1, 1986

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By Corby G. Anderson, Sheikh Abdul Rezan Sheikh Abdul Hamid, Sanjith Udayakumar, Ahmad Fauzi Mohd Noor, Teuku Andika Rama Putra

Chemical and mineralogical characterization of Malaysian monazite, a phosphate mineral, bearing rare earth elements separated from the tin tailings originated from Ipoh, Perak, Malaysia, was performed in this paper. The study aims to collect detailed information on the chemical composition, crystal phases, and microstructure of the mineral monazite concentrate that would aid to optimize the subsequent hydrometallurgical processes for high-efficient separation of thorium and other associated rare earth elements. A systematic characterization study of the concentrate was conducted using techniques such as optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared spectroscopy (FTIR). These techniques analyzed the morphological details on the surface, elemental analysis, and mineral association assessment and identified the surface functionalization groups. The bulk composition and the mineral phases in which the elements are present were studied by wavelength-dispersive X-ray fluorescence (WD-XRF) and X-ray diffraction (XRD) studies respectively. The XRF analysis confirmed the presence of Ce, La, Nd, Pr, and Y (rare earth oxides: REO’s ~ 60 wt.%) while thorium dioxide (ThO2) accounted for 7 wt.% of the total composition. Traces of Ca, K, Al, Fe, Ti, and Mn were also confirmed by SEM elemental mapping. The XRD results confirmed that the concentrate was primarily composed of monazite (Ce, La, Nd, Th (PO4)) along with minor impurity phases of quartz. Automated mineralogical analysis was used as a confirmatory tool to corroborate the preliminary evidences. Based on the particle size distribution analysis supported by SEM, the majority of monazite grains were found to be present in the size range of 170–210 μm. Strong bands of PO4 and SiO4 were observed in the IR spectra corresponding to the phospho-silicate matrix of the REE mineral.

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By Carl Hansen

Sonora Mining Corporation (SMC) operates the 6,000 tonne per day Jamestown open pit gold mine in the Mother Lode district of California. The mine has been in operation since January, 1987, and has produced approximately 7,800 kilograms of gold since start-up. The property consists of five ore bodies lying along a five kilometer stretch of the famous Mother Lode vein system. At present, only the Harvard ore body is being mined. The Harvard pit is centered around a historic underground mine of the same name that was operated from 1896 to 1916. The present ore body averages 2.5 grams gold per tonne as free milling gold and auriferous pyrite. The project consists of the open pit mine and concentrator complex in Tuolumne County, California, and a carbon-in-pulp leach plant located near Yerington, Nevada.

Jan 1, 1990

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By Swan. J. D.

Repairing and replacing equipment damaged by corrosion and abrasion is a major cost throughout industry, especially in the coal mining industry. Careful study of corrosion and abrasion, and their causes and effects, often leads to the selection of alternative materials which can provide economies. What, actually, are corrosion and abrasion and how do they contribute to the cost of operating a coal-preparation plant? Furthermore, what can be done to alleviate corrosion and abrasion problems and thereby reduce operating costs? These questions will be answered in the following discussion, which will describe the destructive action of corrosion and abrasion and give several methods for controlling corrosion and abrasion losses, These methods include the substitution of stainless steel for carbon steel, the use of corrosion inhibitors, and the use of design to eliminate corrosion and abrasion. Examples will be given illustrating the benefits that have resulted in plant tests when these methods of controlling corrosion and abrasion were used.

Jan 1, 1970

By J. J. Knoerzer

The scheduled replacement of Inland's A & B coke batteries in Plant No.3 posed some serious problems in terms of pollution control and strained sources for medium volatile coal for a conventional blend. The state-of-the-art of air pollution control during the charging step in the conventional slot-type coke oven has been less than satisfactory. In addition, the work done at the Illinois Geological Survey showed that by preheating the coal blend prior to charging a greater percentage of Illinois coal could be used to produce a high quality metallurgical coke. To assist The Management in the- decision on A & B replacement, Inland Steel conducted a full-scale test program on coal preheating and pipeline charging utilizing the Coaltek system installed on No. 2 battery of the Semet-Solvay Division of Allied Chemical Corporation. The basic objectives of the test program at Semet-Solvay were as follows: 1. Determine the feasibility of producing high grade metallurgical coke from preheated blends containing more than 60% Illinois No. 6 coal. 2. Confirm the performance characteristics in one of the Inland blast furnaces of the coke produced with 75% Illinois coal in the blend. 3. Verify several claims by Coaltek such as: a) Pipelining the hot coal presents no difficulties while essentially eliminates the air pollution problems associated with the conventional charging system. b) Preheating of the coal blend permits the use of higher percentages of high volatile, marginally coking coals (such as Illinois No. 6) in the blend as compared to wet charging.

Jan 1, 1973

By Richard C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1982

By D. Bleazard

Barrick Goldstrike Mines, Inc. is actively involved in improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. The identification of equipment failure modes and the development of associated capital asset management practices can minimize failure consequences. Successful programs have included; alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle, resulting in an associated reduction to repair costs and equipment down time.

Jan 1, 1997

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964