Search Documents

By Georges E. Vaillant

Air pollution control in primary aluminum smelter . Various processes are known for air pollution in electrolysis plants. Mainly two systems have to be taken into consideration: -Treatment of concentrated gases collected directly from hooded pots. This is normally achieved by either dry or wet process. This is not the object of this paper as these processes have been already described. -Treatment of low concentrated fumes. A certain amount of gaseous and solid fluoride (35 % of total fluor pollution) goes out of the hooded pot. Gases commonly called secondary fumes are generally treated by wet process. The object of 'this paper is to describe two plants with specific treatment for secondary fumes. 1/ A plant in operation in Vlissingen (Netherlands) for PECHINEY. 2/ Presentation of tests carried out by a specialized Company. The results of such tests have been used for the design of the scrubbers presently under construction for ALUMINIO ESPANOL San Ciprian (Spain).

Jan 1, 1978

By L. S. Fountain

A national survey, 1978-1980, found 180,973 waste impoundments used by industrial mining, municipal and other interests. Possibly 27,000 contain hazardous materials. The potential hazard of leaks polluting water supplies is a growing concern. An electrical technique was developed to efficiently and speedily detect and locate leaks in geomembrane-lined liquid impoundments without emptying the contents. A potential applied between the liquid and earth causes electric current to flow through leaks in the insulating geomembrane material to ground. The cur- rent density around the leak is used to detect and locate the leak. Field tests show single and multiple leaks 2.54 cm in diameter or less can be detected and located to within less than 30 cm.

Jan 1, 1986

By Ihor Kunasz

The high lithium demand forecasted for some high tech applications and batteries for electric and hybrid-electric vehicles, in particular, has sparked increased exploration for lithium, particularly for lithium- and potassium-bearing brine deposits. The latter have generally followed the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) NI 43-101 guidelines on resource reporting, formulated for hard rock deposits (metals and industrial minerals). While a number of the requirements can be appropriately applied to brines, brines are fluids and require a specific analysis leading to a distinct set of reporting requirements. Brines cannot be considered industrial minerals because the various elements occur as ions in a dynamic fluid, rather than being chemically bonded in a solid. Although chemicals are produced from brines, brines have no relation to industrial mineral deposits. This article analyzes the recently released (Nov. 1, 2012) document CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines, in light of the practical knowledge available from existing brine operations. It recommends modifications to the guidelines, which, if applied in their present format, will result in overstating resources and reserves and mislead potential investors. The CIM Best Practice Guidelines for Resource and Reserve Estimation for Lithium Brines document is generally descriptive and does not fully address the methodology for brine resource or reserve definition. Lithium and other elements (potassium, magnesium) are contained in a fluid, the hydrologic characterization of which should be the principal focus of a brine exploration program. The fundamental requirement in defining lithium brine resources and reserves in a salar is the identification and definition of those formations ? the aquifers ? that will yield brine in a usable quantity to a well, because brines can only be extracted by pumping wells. Fine-grained sediments will never, as required in the summary Table 1, have ?reasonable prospects of economic extraction,? cannot be considered and, therefore, need not be tested. However, the guidelines recommend the collection of solid samples and a high-core recovery for laboratory testing of various sediments instead of focusing on the brine.

Oct 1, 2013

By Guangming Zhao, Nianjie Ma, Demao Guo, Denghong Chen, Yingming Li

Based on the mechanical essence that large-scale plastic failure zone appears in all or part of surrounding rock in soft rock roadway, the numerical simulation method is used to study the rectangular roadway in layered rock strata. It is clarified necessary conditions must be met for soft rock: firstly, the strength condition is that the maximum confining pressure is greater than the uniaxial compressive strength of rock strata. Secondly, the stress environment condition is that the ratio of maximum confining pressure to minimum confining pressure is greater than 3. Thirdly, the angle condition is that The direction of principal stress action enables the plastic zone of weak rock layers to fully develop. At the same time, the quantitative description method of soft rock is given, and the soft rock roadway is redefined. Soft rock roadway refers to the roadway that meets the strength conditions, stress environment conditions, and rock structure angle conditions under certain surrounding rock conditions and in-situ stress environment conditions. After the excavation of the roadway, a large-scale plastic failure can be formed, that is, a butterfly-shaped plastic zone is formed, and the conventional support cannot be adapted. It is difficult to support in engineering. It provides a theoretical basis and engineering analysis method for the identification of soft rock roadway, and the research results have engineering value Soft rock tunnel engineering in coal mines constitutes a vital aspect of soft rock engineering. This field broadly encompasses rock engi- neering concerning large plastic deformations, e.g., soft rock slope engineering and soft rock tunnel engineering. The intricate geological conditions encountered in soft rock tunnel engineering present a significant challenge to support, which has harmed coal production in China. China leads global raw coal production with the annual output of 4.6 billion tons. Annual tunnel excavation supporting this production spans approximately 11,000 km, with over 10% of these tunnels classified as soft rock formations. Soft rock is commonly associated with soft rock tunnels due to their prevalence in engineering projects. However, reaching a consensus on the definition of soft rock has long been an enduring challenge for scholars and engineers. Numerous definitions have been proposed, includ- ing descriptive, index, and engineering definitions. For instance, the International Society for Rock Mechanics defines soft rock based on its uniaxial compressive strength σ ranging from 0.5 to 25 MPa. China's Engineering Rock Body Standards, established in 1994 (GB 50218-94), take a qualitative and quantitative approach to classifying rocks. Rocks are categorized as hard or soft based on criteria such as hammering sound, fragmentation, water immersion effects, and weath- ering degree. Additionally, the integrity of rock bodies is assessed across five categories intact, relatively intact, soft fractured, fractured, and extremely fractured. This classification considers factors like the number and spacing of structural planes, their combination, and the types of structures. Descriptive and index-based definitions fall under the category of geological soft rocks, providing a comprehensive geological perspective on the surface features or strength characteristics. However, these definitions have limitations in engineering practice, which leads to contradic- tions. For instance, rocks with uniaxial compressive strength less than 25 MPa may not exhibit soft rock characteristics if the tunnel is shal- low with low horizontal stress levels. Conversely, rocks with compressive strength exceeding 25 MPa at sufficient depth and high horizontal stress may exhibit soft rock characteristics. Definitions originating from engineering practice have emerged after realizing the inadequacy of discussing soft rocks without considering engineering. For instance, Dong's loose circle theory defines soft rocks as rocks with a loose circle thickness exceeding 1.5 m, which chal- lenges conventional supports. This intuitive definition, widely accepted by engineering professionals, emphasizes the difficulty in supporting tunnels due to extensive damage. However, various tunnel damage poses a challenge in relying solely on the loose circle thickness of tunnels for determining soft rocks. He introduced the concept of engineering soft rocks, which are defined as rock formations exhibiting significant plastic deformations under applied engineering force. Two fundamental mechanical properties of soft rocks are identified the critical softening load and critical soft- ening depth. Rocks below the critical softening load threshold are categorized as hard rocks, while those exceeding it exhibit substantial

Jun 25, 2024

By H. L. Lovall

Huge banks of preparation plant refuse and other non¬saleable materials have accumulated over the years in all major United States coal producing areas. These banks, esthetically and commercially undesirable, can cause air and water pollution and land reclamation and mineral conservation problems for the industry and nearby communities Although some refuse banks have been reworked to recover saleable coal, all remain and accumulation continues. Even those previously processed continue as potential hazards. Among the several problems created by refuse banks, in situ combustion is most treacherous. Of the millions of tons of major accumulations, there are at least 450 refuse banks on, fire at this time Attempts to extinguish such fires are costly, impractical and generally unfruitful. Studies are in progress to evaluate the potential of processing such materials to eliminate the combustion capability and to yield usable fuel and nonfuel products. Aspects of the study now in. development for coal refuse include: (a) evaluation of characteristics (size, sink-float, ash, sulfur and calorific value) of the coal refuse materials which are known to be highly variable, (b) development of an ignition test having significance for in situ conditions, (c) study of processing capabilities (comminution for liberation, pilot plant washing tests), and (d) investigation of potentially significant properties of fuel and nonfuel products which could be altered to enhance their market potential.. Among the latter products are lightweight aggregate, fill for mine slushing operations, construction, etc: Plans are to extend the studies to include the design, erection, and test processing of refuse with a transportable plant,; which could provide basic economic and product utilization data from several locations

Jan 1, 1964

By D. Limpitlaw, E. M. Hoadley

The minerals sector plays a significant role in the development of many Southern African economies. In the Southern Africa region, as in other developing regions, economic development is seen as the key contributor to poverty alleviation and social upliftment. The significant economic contribution of the minerals sector may be reduced by negative impacts on the biophysical environment and on the communities where mines operate. A critical variable in determining the net contribution of mining companies to SD is the degree of transparency with which the companies operate. Transparency is increasingly emphasised as an essential aspect of good governance and SD, but it is also difficult to establish, and is a sensitive issue for mining companies as they compete with each other for minerals sales. Transparent reporting could ensure that the interests of all stakeholders are addressed as company data is subject to informal ‘auditing’ by any interested party. This paper assesses published reports of five companies over a number of years to establish whether it is possible to make an assessment of the companies’ contribution to SD.

Jan 1, 2005

By J. O. Leppinen

FTIR measurements using a special ATR cell were carried out to investigate the adsorption of two thiol collectors, potassium ethyl xanthate (KEX) and sodium diethyl dithlophoshate (NaDTP), on an unoxidized lead sulfide surface. Both qualitative and quantitative determinations of the collectors were made at the coverages from two monolayers down to 2% of the monolayer. The experiments revealed that the thiol collector species coordinate to the lead atoms at the surface of lead sulfide but the surface products distinctly differ from the precipitated bulk lead compounds. There exists a linear relationship between the coverage and the signal intensity of the IR spectra within the coverage range studied.

Jan 1, 1987

By Claus Becker

In Europe, approx. 50 km of traffic tunnels are under construction using Slurry-or EPB Shields or Convertibles of all sizes, among them the biggest slurry shield ever built up to now with 14,20 m diameter. Main characteristics and special features of the machines will be explained relating to geology, cover and water pressure. This gives a comprehensive overview of the latest developments of this kind of machines.

Jan 1, 1999

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

By J. J. Zimmerman

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise data from 2000-2004 show that the continuous mining machine is first among all equipment with 35% of the noise overexposures. Joy Mining Machinery, in collaboration with the National Institute for Occupational Safety and Health (NIOSH), is conducting research to reduce noise generated by continuous mining machines. This paper describes a ?JOY Designed for Noise Reduction? (JOY-DNR; Patent Pending) tail section as a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 45% and 65% noise exposure reduction for the operator when compared to a standard machine. Utilizing this newly developed noise control, along with previously proven controls, will provide continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2010

By LINDSAY BOTTOMER, Tassos Grammatikopoulos, Massoud Aghamirian, MARK FEDIKOW

A master composite (Master Comp) sample was prepared from three pegmatite zones from the Zoro Dyke D1 for mineralogical analysis and heavy liquid separation (HLS). The mineralogical examination was conducted on a subsample that was crushed to approximately P80 = 600 μm. The sample consists of spodumene (10.5 percent), quartz (29.3 percent), plagioclase (29.0 percent), K-feldspars (21.3 percent), micas (5.1 percent), tourmaline (2.9 percent) and Fe-Mn-phosphates (0.1 percent). Liberation of spodumene (88 percent) and gangue minerals, including quartz (89 percent), feldspars (94 percent) and micas (83 percent), is very good at this P80 . The average lithium (Li) concentration is 3.7 percent in spodumene, 2,196 ppm in micas, 1,001 ppm in tourmaline and 115 ppm in K-feldspars. Spodumene accounts for 96 percent of the total Li in the sample. The mineralogical data indicate the potential to recover spodumene by flotation with minimal Li losses due to other Li carriers. The HLS was conducted on a subsample that was crushed to smaller than 6.4 mm, with the smaller than 600 µm fraction removed from this test. The HLS results indicate it is possible to produce a high-grade lithium concentrate, with close to 6 percent Li2O, after the rejection of iron silicates with magnetic separation.

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Hee-Young Chung, In-Mo Lee, Jeongjun Park, Hangseok Choi, Seok-Won Lee

"When using a Tunnel Boring Machine (TBM) during tunneling work, unexpected ground conditions can be encountered that are not predicted in the design stage. These reduce the stability of tunnels, and can result in considerable economic losses. This paper analyzes the potential risk events that may occur due to risky ground conditions. A resistivity survey is utilized to predict the risky ground conditions ahead of the tunnel face during construction. The potential risk events are evaluated considering both the occurrence probability and the impact. A TBM risk management system that can suggest proper solution methods for potential risk events is also developed. Multi-Criterion Decision Making (MCDM) is utilized to determine the optimal solution method to handle risk events. Lastly, an actual construction site, at which a risk event occurred during tunnel construction, is analyzed utilizing the Earth Pressure Balance (EPB) Shield TBM, to verify the efficacy of the proposed system.INTRODUCTION The Tunnel Boring Machine (TBM) method has been widely adopted in numerous tunneling projects because, as a mechanized tunneling method, it is also environmentally friendly, exhibiting minimal noise and vibration when compared with conventional tunneling method. In addition, it provides considerable economic benefits that allow for a high advance rate for long drives during construction. However, the TBM method has a limitation, as it is unable to deal with unexpected situations during construction, as the system is not capable of moving backwards. This leads to delays or even stoppages, and a corresponding increase in construction costs due to the need to arrange for alternative equipment and solutions. It is essential to retain systematic management in order to prevent or deal with unforeseen consequences such as the collapse of a tunnel face, ground surface upheaval or settlement, and construction delay due to water leakage during construction. Therefore, a systematic risk management system that is applicable during the construction stage of the TBM tunnel should be developed, taking into account the predicted risky ground conditions ahead of the tunnel face in advance."

Jan 1, 2016

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By D. A. Norrgran, J. A. Wernham

Introduction In view of the continuing depletion of natural resources, requirements for energy conservation, plant optimization and hazardous waste management, and environmental consciousness, recycling and secondary recovery of materials are being developed with increasing interest Many secondary recovery processes are being developed that apply mineral processing technology. Gravity separation, magnetic separation and flotation have all emerged as explicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. The concept of the alternating magnetic field eddy-current separator was developed over a century ago using rudimentary electromagnets (Patent 400317 issued to Thomas Edison on March 26, 1889). Widespread acceptance was, however, hindered by high costs, marginal results and poor economic incentives for secondary recovery. With the recent increased interest in secondary recovery and the development of high-energy rare earth permanent magnets, the eddy-current separator has now gained prominent acceptance. The separation forces imparted by an eddy current separator are the function of the magnetic field intensity and the alternating frequency of the magnetic field. The evolution of permanent magnets has provided a cost effective alternative for the generation of high-intensity magnetic fields. High-energy rare earth permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymium-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits. The eddy-current separator has been successfully applied in several metal sorting and recovery operations. Most common is the sorting of metal from shredded automobile scrap and municipal waste. With the advent of high-frequency, high-intensity magnetic fields, the separator has advanced to the point where it has direct application in the beneficiation of fine sized metals. Relatively fine sized (-1/4 in.) metal bearing slags and spent foundry casting sands as well as precious metal hearing electronic scrap demonstrate excellent metallurgical response to the eddy-current separator, and applications have progressed to finer materials and more selective separations. Theory Electrical currents are induced in all conductors when exposed to an alternating magnetic field. The induced current generates a magnetic field in the conductor that opposes that of the alternating magnetic field. Figure 2, is a schematic illustration of generated eddy currents. In this particular example, the alternating magnetic field is produced by a series of permanent magnets mounted on the circumference of a rotor. The permanent magnets have alternating polarity. As the rotor revolves, an alternating magnetic field is produced, and the rate of revolution determines the frequency of the alternating magnetic field. When a conductor, such as a metallic disc in the illustration, is placed in the alternating magnetic field, a closed loop current flow occurs. The current loop in the conductor produces a magnetic field that is a mirror image of the alternating magnetic field. At any point in time, the induced magnetic field in the conductor directly opposes the alternating magnetic field. This opposition of magnetic fields produces an instantaneous repulsion in the conductor. The conductor is consequently repelled from the rotor. The alternating magnetic field has no effect on nonmetallic materials as they pass through the magnetic field and discharge the rotor in a natural trajectory. [ ]

Jan 1, 1992

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By C. C. Clark

The national Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health, Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system, it is necessary to know when the material has developed a compressive strength of approximately 1 MPa (145 psi), the early threshold for safe re-entry of miner and machine into shotcreted mine workings at this value, the material has developed enough strength to be self-supporting and to allow for installation of other ground support components that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on site in the first six hours after application using a partial beam test standard, a STM C 116-90 (1990). These advances were demonstrated in tests with five commercially available shotcrete mixes, sprayed as dry shotcrete using field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. Measuring the early strength properties of shotcrete directly at the mine site can improve mine safety by identifying appropriate re-entry times and providing a convenient means of conducting on site quality control during shotcrete applications.

Jan 1, 2011