Search Documents

By Omid Asghari, Amin Mousavi, Arshad Ranjbar

Geometallurgical modeling of the production benches is an attempt to estimate the geometallurgical variables of the different ore domains, which leads to a better understanding of the ore and its properties. Having geometallurgical variables results in a more accurate prediction of ore characteristics, an improved drilling and blasting operation, and better efficiency of the processing plant. In this research, the geometallurgical variables required for the geometallurgical modeling of the extraction benches are discussed. Then, the relations between Bond work index (BWi), as one of the most important geometallurgical variables and the primary grindability index, and rock geomechanical properties are investigated based on the previously published studies. The BWi is the main parameter for measuring the resistance to the grinding of ore minerals. It represents the energy required for processing (e.g., crushing, grinding) ore rocks in the beneficiation plant. As a real case study, BWi of a production bench in Sungun Copper Mine, located in East Azarbaijan province, Iran, was estimated. The rock’s geomechanical properties were measured using laboratory tests, including uniaxial compressive strength, Brazilian tensile strength, point load strength, and hardness. Then, BWi was estimated using the proposed formulas in the literature and the results of the rock’s geomechanical properties. The selected bench consists of three ore zones and two dyke domains. The laboratory tests revealed that the first ore zone has a slightly higher compressive strength than the other two zones, while the compressive strength of the waste rocks is larger than the ore domains. Using the proposed equations in the literature, the predicted values of the BWi for the samples in ore zones are in the range of 6.36 – 14.44 (kWh/t), and therefore this wide range must be considered when the short-term production schedule is planned. In addition, variations are observed in the samples within a specific zone and between the ore zones, demonstrating heterogeneity in the selected bench. Finally, wide-open results obtained by different equations show a necessity to perform a geometallurgical program specifically for the Sungun mine.

Oct 28, 2021

By Adrian Molinari

A radioisotope probe (Minexan 202) capable of simultaneously analyzing a mineral slurry for five elements and pulp density has been developed by Outokumpu Oy, Finland. The probe is designed to operate immersed directly in a process stream, or it can be equipped with a flow cell through which passes a continuous sample of the main stream. A minicomputer (PDPII) is used to control the probes and calculate the assay data. This paper describes the probe as applied to slurry analysis and compares it to the conventional x-ray on-stream analyzer (Courier 300).

Jan 1, 1977

By Jack Bedder

"Editor’s note: We would like to thank those who make this annual issue possible. A special thank you goes out to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division Technical Committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Ebrahim K. Tarshizi, member SME, of Michigan Tech, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include: • Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Yin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Jasson Giddens and Swadhin Saurabh, members SME, of Oil Dri Corp of America and Mill Creek Engineering, respectively, chemical raw materials.• Snehamoy Chatterjee, member SME, of the Michigan Tech.• LeDeana Roberts and Shubham Verma, members SME, of Imerys and U.S. Oil Sands, respectively, fillers and pigments.• Thomas Hilderbrand and Kaiwu Huang, members SME, of Thiele Kaolin Co. and Virginia Tech, respectively, sorbents, filters and process aids.• Rhaghav Dubey and Edgar Blanco, members SME, of Outotec and FL Smidth, respectively, specialty mineralsAntimony generally occurs along with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main one.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. In 2016, it accounted for more than three quarters of the global mine supply out of a world production figure of 130 kt (143,000 st), according to the U.S. Geological Survey. The biggest, and most high-grade deposits are found in southern China, with the largest mines located in Hunan, Guangxi and Yunnan provinces. Tajikistan, Russia, Australia and Bolivia are the largest mine producers outside China. A new antimony project in Oman made progress in 2016, producing first metal in April 2016 in test facilities, and then ordered three furnaces for a 26 kt/a (28,600 stpy) antimony metal and oxide smelter that is due on stream in late 2017.Antimony ingot production is not as widespread as is antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries, where environmental legislation is less stringent.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe — which relies on imported feedstock, mostly from China. Antimony also enters the supply chain through recycling. Lead containing antimony is produced in a number of countries, mainly in secondary lead smelters. Typically, a blast furnace charge containing used or discarded battery plates, type metal or bearing metal is reduced to lead bullion, which is refined in reverberatory furnaces and melting pots. In the main, the antimony recovered is consumed in metallurgical applications. China was the biggest secondary antimony producer in 2016, and accounted for 25 retardants and lead-acid batteries. Flame retardants accounted for roughly 50 percent of consumption in 2016 with batteries representing about 25 percent. Other end uses include plastics and heat stabilizers, ceramics and glass and a variety of metallurgical applications. Demand has been sluggish since the global financial crisis, mostly because key markets failed to recover strongly from the downturn, particularly in Europe."

Jan 7, 2017

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014

By Rainer Kahrger

This paper is a follow-up to the paper presented at the SME meeting in April of 1996. Since then, the El Abra facility has been started up, 9 months ahead of schedule, and has processed about 45 million tons of ore and produced over 700 million pounds of copper. For those unfamiliar with the El Abra materials handling and leaching facilities, a brief overview of the facility is provided. The paper will then deal in detail with such aspects of Conveyor 103, the long regenerative overland conveyor, including: actual running resistance starting and stopping procedures emergency brake test at 10,000 t/h Additionally, we shall take the opportunity to report on a catastrophic culvert collapse in October 1996, which stopped the conveyor abruptly at full speed and under high load condition, causing a belt breakage. We would like to use this opportunity to thank the management of El Abra and Cyprus Amax for providing assistance and allowing us to present this paper. The El Abra team deserves a great compliment for building this one billion dollar facility in record time in a remote area of a high-altitude desert with no existing infrastructure, and for bringing it so quickly up to full operating capacity. The El Abra management had to assemble a completely new operator team. Considering the above circumstances, it took a great effort by all involved to achieve success. The official performance test which was required by the lending banks was successfully concluded in November 1997.

Jan 1, 1998

By Danny Chan, Shahram Tafazoli, Nicholas Himmelman, Edmond Chow

"While wearable technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply wearable technology to improve productivity and safety in the mining industry.This article discusses the value proposition of using wearable technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to wearable technology, are defined. Finally, the concept of MetricsGear, the first wearable technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear is designed to notify the user with minimal distraction to keep the user focused on his or her primary task and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: timecritical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some human-computer interaction (HCI) experts classify notification types based on the interruption, reaction and comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing and information to identify which equipment and when the tooth went missing (Fig. 1)."

Jan 1, 2014

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By V. McLemore, N. Dunbar, K. Donahue

There are three principle lines of evidence that indicate the clay minerals found in the Goathill North (GHN) rock pile at the Molycorp mine are predominantly a product of hydrothermal alteration, not weathering. The unweathered drill core and samples from GHN have similar types and abundances of clay-mineral groups based on XRD analysis. Chemical analyses from the electron microprobe reveal similar chemical compositions for the hydrothermal alteration clays in drill-core samples and clays found in the rock pile. Textural evidence gathered from petrographic and microprobe examination also suggests a hydrothermal origin for clay minerals.

Jan 1, 2007

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By Mohamed A. Younis, Paul J. Headland, Paul H. Madsen, Vojtech Gall

INTRODUCTION A 100 ft long, 20 ft high and 18 ft wide NATM tunnel was excavated through grouted clean sands beneath a busy city street, including a variety of existing utility lines. The new tunnel associated with a hospital expansion will serve as a pedestrian tunnel connecting a parking structure with a new hospital facility. Tunnel construction started on December 15, 2005 when drilling for the grouting program started and was completed on May 26, 2006 when the tunnel final lining was completed. The tunnel was constructed by Kiewit Construction Company as a tunnel subcontractor to The Christman Company who is constructing the hospital facility for Spectrum Health in Grand Rapids, Michigan. URS was the project designer. GallZeidler Consultants, LLC were the contractor’s NATM consultant. PROJECT DESCRIPTION The Michigan Street Pedestrian Tunnel is a component of the Michigan Street Development located along the north side of Michigan Street NE between Coit Avenue NE and North Division Avenue in the downtown area of the Grand Rapids, Michigan. The Michigan Street Development includes a parking deck and four new towers to be constructed over the proposed parking deck. The tower planned furthest east is being developed by Spectrum Health as the Lemmen-Holton Cancer Pavillion. The purpose of the pedestrian tunnel is to connect the proposed Lemmen-Holton Cancer Pavillion with the future Spectrum building to be located on the south side of Michigan Street NE. The southern end of the tunnel was constructed with a bulkhead until the future Spectrum building is constructed at which time interconnection will be required. The tunnel site plan and profile are shown in Figure 1, Site Plan, and Figure 2, Tunnel Profile. Several challenges were faced during the design and construction of the Michigan Street Pedestrian Tunnel. These challenges included compressed design and construction schedule, maintenance of traffic and protection of old underground utilities. The tunnel was being constructed as part of the Michigan Street Development and coordination with other concurrent construction activities was required. The tunnel was constructed within a specified window of time to allow other associated construction activities to take place without compromising the overall project schedule. The design started in June 2005 and construction was completed by June 2006.

Jan 1, 2007

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By A. Noble

The design of separation circuits can be a complex, labor-intensive and costly process. While the engineer?s experience along with extensive data sets and simulation are crucial tools for determining the final solution, a more fundamental approach is suitable to compare preliminary options and reduce the number of potential alternatives. In light of this need, the authors have developed the Circuit Analysis Reduction Tool (CART?). This software package relies on the fundamental principles of linear circuit analysis; however, the solution methodology has been streamlined to automatically incorporate stream splitting and unique separation performance for each unit. The resulting tool allows preliminary analysis of circuit designs without the need of detailed feed characterization. In addition to the basic analytical approach, this paper supports the veracity of the methodology with several simulated examples for various separation models.

Feb 27, 2013

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By J. E. Kulas

Red Dog is a Mississippian to Permian aged sulfide deposit located in the western Brooks Range north of Kotzebue, Alaska. It belongs in the family of black Shale hosted sedimentary exhalite deposits but lacks classic sulfide sedimentary textures. Pervasive silicification, and a significant portion of the mineralization, is replacement in nature. An extensive feeder vein system cuts the footwall and the exhalite package. A Jurassic to cretaceous age compressional event has repeated the ore section through thrust faulting and folding. The orebody contains 77,000,000 metric tons averaging 17.1% Zn, 5.0% Pb and 82 g per metric ton of Ag. Weathering has locally altered the sulfides to sulfates and formed elemental sulfur.

Jan 1, 1992

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Underground mining environments bring occupational health and safety issues with some severe dangers such as mine disasters like explosions. During such events, miners might escape using main access openings, or find a safe haven like refuge alternatives (RAs) to wait and be rescued and evacuated to the surface. In this paper, RAs are explained with their early and current applications. A classification as permanent and portable is explained depending on the conditions and their abilities. This classification is followed by the utilization and survivability of RAs with the requirements and recommendations of the main mining countries. Based on the utilization and survivability constraints, basic human requirements, waiting for a rescue team, and the required physical specifications of RAs during the events are analyzed in detail for various countries with their regulations. Among these, the specification, resistance to the explosion, is discussed in particular, and the studies in the literature are examined in terms of structural deformation. The highest deformed zones, the beneficiation of reinforcing steel components such as stiffeners, and the simulation approaches are investigated through this review.

Sep 24, 2022

By E. H. Cho

A current environmental concern is the cleanup and restoration of soil contaminated with low-level radionuclides at DOE sites including the Nevada Test Site. At the present, there is no applicable process to economically and effectively deal with the remediation of contaminated soils. This situation requires development of a selective flotation process to separate the radionuclides from contaminated soil efficiently and economically. In this study, a minus 200 mesh size fraction of pure cerium dioxide was used as a surrogate for plutonium oxide which is the major contaminant at the Nevada Test Site. A Hallimond flotation cell was utilized to examine the flotation behavior of cerium dioxide with oleic acid under various conditions of pH and collector concentration Mechanical cell tests were conducted to float the surrogate from a mixture with uncontaminated Nevada Test Site soil in the absence and presence of calcium carbonate as a carrier. Two different sizes of the carrier (minus 150 mesh and 65-150 mesh) were tested. It was found through the Hallimond cell flotation tests that the cerium dioxide could be floated well at pH's 4 and 9 with 10-3 molar oleic acid. It was also found that the addition of the carrier drastically enhanced the flotation recovery of cerium dioxide. The flotation recovery of the surrogate increased from 34 % to 65 % by adding only 0.5 % calcium carbonate (minus 150 mesh) in the feed and also increased to 95 % by adding 10 % of this carrier to the feed. The finer size fraction of calcium carbonate (minus 150 mesh) was more effective in recovering cerium dioxide than the coarser size fraction (65-150 mesh) The flotation method utilizing a carrier of calcium carbonate seems to provide a high potential to be used for the remediation of soil contaminated with radionuclides at various Department of Energy's nuclear weapon sites.

Jan 1, 1996

By P. J. Bethell

Background Increasingly complex geological conditions, with the presence of high ash binders in the mining horizon were encountered at the A.C. I. Dugout Mine near Price, Utah. This led to the production of high ash coal from the Dugout Mine during 2003 and 2004. This material had poor marketability and posed operating issues for the utilities burning the coal. Ash levels increased from typical levels in the 9-12% range to between 15 and 25%. etween 15 and 25%. Reviews of the mine plan and expected geological conditions indicated that further periods of high ash production could be expected. Action Plan Detailed sampling of the mine high ash production was carried out. The majority of the coal from the Dugout Mine is trucked to the Savage Coal Terminal (SCT) at Wellington, Utah where it is stored in multiple piles by quality. Coal at the mine is segregated by a CoalScan 2600, on-line analyzer into high ash, low ash and rock chute (waste material). From these piles, the material is crushed prior to shipment to SCT. The samples obtained from the various high ash piles were subjected to detailed sizing and washability analysis. Once this information was obtained, alternative circuit configurations were evaluated to process this material into a salable product. Water supplies in the arid terrain where the plant is located are scarce. This factor played a part in the final circuit design.

Jan 1, 2008