Search Documents

By Alafara A. Baba, Yakubu A. Dallatu, Kehinde I. Omoniyi, Shemang Y. Chindo, Edith B. Agbaji

As a result of the rise in global demand for pure copper, there is urgent need to consider the processing of low-grade chalcopyrite ores. Ammoniacal leaching solutions have been reported as an effective and efficient leachant for the dissolution of chalcopyrite. This work reports different parameters that influence the leaching kinetics of a Nigerian chalcopyrite-rich siderite ore obtained from Wase Local Government Area, Plateau State, Nigeria, and assayed as 11.30 wt% of Cu. At the optimum leaching conditions (0.4 mol/L NH3-( NH4)2SO4 leachant concentration; 75 °C reaction temperature; 45 μm particle size), the extent of chalcopyrite ore dissolution reached 87.4% within 120 min. The dissolution rate was affirmed to conform to the diffusion control mechanism with the activation energy, Ea, of 38.84 kJ/mol and a reaction order of 0.661 for the leachant concentration being established. The leaching mechanism was affirmed by characterizing the raw ore and the leached product by XRD and SEM-EDS analysis. Ascertaining optimal leaching conditions for copper using alkaline leachant is advantageous from the environment and economic points of view.

Jan 6, 2023

By R. Vogt, H. C. Mult, F. L. Wilke

INTRODUCTION At present, the capability of production planning software based on Linear Programming (LP) is still limited to the optimization of the single LP-run. This is due to the LP-model itself which cannot consider the interdependencies between individual LP- runs. With regard to planning of selective mining this limited way of optimization frequently leads to situations, where the remaining and accessible ore blocks do no longer allow to produce ROM-ore in the qualitative composition required by the ore processing plant. However, many of the aspects taken into consideration when setting up production plans built from mutually dependent LP-runs cannot be modelled in a system of linear equations. They are thus unsuited for treatment with LP and have to be taken care of by the planning engineer without any assistance by the system. The KBS currently under development is intended to assist the planning engineer in designing a production plan under special consideration of the combination of consecutive LP-runs and blending beds. It is not necessarily intended to find the optimum solution within a given planning situation which is, anyway, hard to determine due to the multitude of influences. The objective is rather to work out a good and - from the practical point of view - feasible production plan. The new aspect with respect to mine planning is the integration of expert knowledge and experiences via the KBS into the planning process in order to support the planning engineer. The planning system is being developed in close cooperation with an iron-ore open pit mine. COMPONENTS OF THE PLANNING SYSTEM The software is being developed on a workstation under UNIX and comprises the components LP, CAD-module and the KBS. The applied multi-goal LP-algorithm is an in-house development of the Department of Mining Engineering at Technical University Berlin. It was already successfully implemented within other mine planning programmes and was only slightly adapted to the specific needs of the present system. Within individual LP- runs it finds the optimum qualitative composition of ore production in the sense of the selected optimizing criterion and under the given restrictions: i.e. it determines tonnages to be mined from blocks in order to optimally meet the requirements of the ore pro- cessing plant. A CAD-module based on the commercial SURPAC package in combination with a simulation device is used to graphically depict the block model and progress of mining. Both LP-algorithm and CAD-package are integrated in the KBS. It has been decided to use the shell NEXPERT OBJECT as it is a hybrid system which supports both rule-based and object-oriented knowledge representation. MINE-MODEL AND LP-MODEL KBS have to be tailor-made for specific planning problems. Therefore, it had to be decided which specifications of the iron-ore mine should be represented in the model. As the limited possibilities of a university institute do not allow to develop a KBS for mine planning which is ready to use in industry, it was decided to concentrate on those characteristics that can be regarded as typical for iron-ore surface mines and that seemed to be suited for treatment with knowledge-based techniques. The following chapter summarizes the most important features of the mine model. The description of the requirements to the mine's sales products is followed by an outline of the applied LP-model. Mine model • The model of the mine as it is used for planning consists of • the block model of the deposit, • the mobile equipment, • stockpiles and blending bed and • the requirements to the sales products. The deposit is described by a block model which contains data on the chemical composition, LOI, grain size and tonnages. Grain size was included as it is important for the two sales products of the mine. Furthermore, it is known whichs blocks require and which don't require blasting; this is relevant to the assignment of loading equipment to individual blocks. The blocks are devided in three categories: • ore, which will directly be taken to the blending bed; • waste, which will be put on the waste dump; and • blocks which will be either transported to the blending bed, to stockpiles or to the waste dump depending on the specific planning situation. This decision is made during planning. Neighboring blocks are combined in mining areas to which the loading equipment is individually assigned. Mobile equipment comprises shovels and wheel-loaders as well as trucks. The characteristics of the loading equipment are important for their ability to load different blocks and for the permissible degree of their re-positioning etc. The mine disposes of a blending bed for homogenization of the production, of a waste dump, and of several stockpiles with different ore qualities. The requirement to make only limited use of the stockpiles for economic reasons is included in the KBS. According to long term planning two commercial products have to be produced, which differ both in grain size and qualitative composition (TABLE 1). Their mass-proportions in the blending bed have to be within a fixed range. Not considered in long term planning is the occasional need for lump ore, which occurs at very short notice and has to be produced in a "campaign-like" manner. This requires the total re-arrangement of all plans for on- coming blending beds and would therefore be ideally suited for

Jan 1, 1996

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

By R. K. Singhal

The underground coal mining systems have kept pace with the developments that have occurred in other types of mining industry. A diversified group of machines with high horsepower motors, built-in microprocessor technology and with numerous options to satisfy the miners need in a varying geological environment are now available. A brief review of this existing technology and its likely status within the next 21 years is presented. Discussed also are some of the on-going advanced developments in electronic mechanization, remote control and automation together with mine wide data monitoring and management systems and facilities to process and transmit data to remote computerized stations.

Jan 1, 1989

By J. Hanna

Four Ca-bentonitic clays from Alabama were evaluated for use in Diammonium Phosphate (DAP) or Urea Ammonium Nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium exchanged Alabama clays, were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Na-modified clays, prepared according to the TVA soda ash method, was as good or even better than those observed for the Mg-, Na/Mg-or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1989

By Christian F. Baiz

The author will present a discussion of the steps which must be taken by the prospective developer of a small mining operation to establish technical credibility when seeking financial backing. Particular emphasis will be given to the differing levels of technical work (and their relative cost) which must be accomplished to supply the information necessary to satisfy potential investor groups, whether they be other mining companies, equity investors, or financial institutions such as venture capital firms or commercial banks.

Jan 1, 1981

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By Walter H. Schwedes

Ore grinding mills are really just slowly rotating barrels, but barrels that are growing in size so fast that the application of electric drives for them is rapidly approaching a technology like that for wind tunnels or pumped storage drives. This application is particularly worthy of care because some 40% of the 75 megawatts of power used by a large copper ore concentrator, or some 60% of the 200 megawatts supplied to a large iron ore concentrator, are for grinding. These ore plants are located where the ore is, not where a utility happens to be. So, the challenge is not only to choose a drive and .power transmission for reasonable cost, high performance, reliability and minimum maintenance, but to afford the interface between mill drive and power distribution and source systems to minimize the whole ore plant's monthly power bill, or costs of self generation. Conclusions can be reached in optimizing a drive selection only for each particular ore plant's set of parameters, but by identifying the criteria for selection and then weighting each type of drive per criteria, yardsticks for final choice become apparent. This is the purpose of this paper. Grinding action takes place inside the barrel, where the ore charge is ground with the aid of balls, or mill length rods, or large chunks of ore as in autogenous grinding.

Jan 1, 1972

By D. R. Babich, E. R. Bauer

Noise-Induced Hearing Loss (NIHL) continues to be a concern of the mining industry. A new noise standard (30 CFR, Part 62) is aimed at reducing NIHL in mining through engineering and administrative noise controls. However, the difficulty and expense of implementing engineering controls can make administrative controls an attractive alternative for reducing worker noise exposure. Over the last three years, the National Institute for Occupational Safety and Health (NIOSH) has conducted worker noise exposure surveys in underground and surface coal mines and coal preparation plants. The surveys revealed numerous possible administrative controls and an approach to implementation and analysis. The surveys have shown that worker dosimetry, time-motion studies, and equipment noise profiling are important aspects of effectively utilizing administrative controls. A description of the approach for selecting, implementing, and evaluating administrative controls, and a list of administrative controls, are reported.

Jan 1, 2004

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By R. J. Gary

Why would a company in its right management mind risk a fuel conversion program on a fuel that can't burn if it's too wet or too dry, too hot or too cold, too coarse or too fine, or doesn't have enough Btu's to supplement good combustion? On December 23, 1981, two months ago, we finished our first ten years of burning lignite -- this unconventional coal. It is from that experience that I am qualified to address you today. As some of you here probably already know, my company, Texas Utilities Generating Company, has pioneered the utilization of Texas lignite for electric power generation on a large scale, and I think it is fair to say that we have done this pioneering work largely on our own. Some of us feel like Noah did when he built the arc! I have titled this presentation "The First Lignite Decision" because our company was the first to make this major decision in Texas in the mid-1960's. It was a big decision, and at the time, perhaps a bold one. When you look at the conditions that existed in the mid-1960's, you can see why.

Jan 1, 1982

By B. M. Davis

The problem of assessing uncertainty in grade estimates has been a topic of research and debate since kriging was first introduced. Use of the kriging variance was originally touted as all that was necessary in order to produce confidence limits for grade estimates. Since then the prudence of using the kriging variance for confidence interval estimation has been questioned, and techniques such as the jackknife and conditional simulation have been proposed to develop "true" interval estimates. This paper compares the differences between interval estimates produced by the three methods and makes conclusions about the performance of confidence intervals produced by the different methods.

Jan 1, 1997

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

By Valerie Kollonitsch

Functional mineral pigments are used in large quantities in paint, paper, plastics, rubber, textiles, agriculture, and several other industries. U.S. consumption in 1969 is estimated at over 5 million tons a year, valued at nearly $150 million, as shown in Table 1. Originally extender pigments were employed only to lower cost. They were thought of merely as adulterants to replace more expensive prime pigments and binders. However, over the years their role has become better understood, and today their main functions are: - Increasing strength, stability, and service life. - Improving surface properties. - Enhancing application and processing properties. - Extending prime pigments. - Controlling viscosity and package stability - Lowering overall costs of the finished product. The principal minerals used as functional pigments are kaolin, ground calcium carbonate, talc, and asbestos. Other minerals include barytes, attapulgite, diatomite, mica, ground silica, wollastonite, and nepheline syenite. Several synthetic products, including precipitated calcium carbonate; precipitated, gel, and fumed silica; alumina trihydrate; and barium sulfate, compete with mineral products. They are more expensive, but often have more closely controlled particle size or other properties because they can be tailor-made according to the requirements. This paper covers only natural products selling for $10 or more a ton, approximately the lower limit for pigment grades. Data refer only to consumption in pigment applications. For example, such applications as filter aids for diatomite are not included. Key properties of the major mineral pigments are given in Table 2. It is important to note that these properties are primarily physical rather than chemical. In general, these products are sold to performance specifications for what they can do rather than on chemical composition specifications on what they contain.

Jan 1, 1969

By J. A. M. Cano

A brief introduction is made on the existence of sulphides in the top gas of the Midrex Shaft Furnace, giving consideration to the operation of the furnace and the liberation of sulphur as well as its consequential effects on the reduction process. The text shows a study of sulphur distribution in the pellet, emphasizing the importance of this distribution in relation to the liberation of sulphur during the reduction. A study was made to determine the sulphur compounds that exist in the pellets, showing ways of controlling the sulphur distribution and reducing its liberation?during the reduction.

Jan 1, 1989

By John M. Hill

Automation technology has many facets, some well tested and proven, some yet to be put to the acid test of economic reality. In this paper, we will limit our purview to the former. Consider, if you will, an automated handling system combining high-speed conveyors and automatic devices on-line which not only provide signals for routing and sorting, but also format those signals for the production of manufacturing, inventory, shipping and billing paperwork. This is not futuristic, but practical and a realistic accomplishment. Therefore, the following discussions will address today's challenges not with tomorrow's solutions, but rather, with an established technology which is playing an increasingly prominent role in materials handling systems. Until recently, relatively modest importance has been attached to the timeliness of information feedback from the production or assembly line, warehouse or distribution center. Thus, initial applications of automatic identification equipment focused almost exclusively upon the control of materials flow - that is, routing, sorting, etc. However, these systems have performed successfully and quietly established an enviable track record as reliable materials control tools.

Jan 1, 1973

By Ziyuan Liu, Xun Zhang, Yan Wei, Hang Qiu, Shaomin Lei, Yubiao Li, Yu Meng, Min Lin, Bin Liu

High-purity quartz (SiO2) is an important material widely used in many industries, including semiconductor technology, telecommunication, and optics. The content and distribution of impurities in quartz significantly affect the processing methods. This paper provides an insightful review on the processing of high-purity quartz, covering the analytical techniques, separation methods, and the critical procedures used to assess the quality of quartz ore. More importantly, the critical review of the thermal phase transition separation method for fine-grained mineral inclusions, micron-grade fluid inclusions, and lattice-bound trace elements is notably opened for the first time. It is proposed that the research field as a monopolized industry would benefit by expounding the critical problems that occur during the preparation of high-purity quartz.

Jun 22, 2020

By R. A. Burns

The production of kaolin and calcium carbonate in North America exceeds 13 million tons sold into higher value market segments. With a few exceptions, the markets supplied exhibit mature growth rates. In some market sectors, technology changes have and continue to occur shifting pigment-type consumption and growth. New sources of supply will impact current businesses. New product and process developments for kaolin and calcium carbonates are continuing. Each of these issues is examined in developing a view of the future for kaolin and calcium carbonate in North America.

Jan 1, 1997

By D. Nutakor

This paper presents the results of a study conducted on a slope failure that occurred in the Q7 mining cut at Rio Tinto's Bingham Canyon Mine. The slope failure occurred in a weak rock mass with an estimated rock mass rating of 25%. The failure mechanism was of the circular type, involving ten 15-m (50-ft) benches and covered a total width of 152 m (500 ft). The analysis used Adam Technology's photogrammetric method with a two-dimensional rock fall simulation program (RocFall software) to design a 3-m- (1 0-ft-) high berm located 7 m (24 ft) from the toe of the failed mass. Back and predictive analyses were performed on a cross-section through the slide using Slope/W software, resulting in flattening the interramp angle (IRA) from 44° to 38°. This design modification produced a factor of safety (FOS) of 1.14. Sensitivity analysis involving FOS vs. pore water pressure showed that FOS is sensitive to water saturation. A dewatering system using a series of horizontal holes drilled below the slide and dewatering holes drilled from a drainage gallery has since been established to improve the stability of the slope. Throughout the one-year period since this investigation, no significant slope movement has been detected by the slope stability radar, and mining is in progress below the failure.

Jan 1, 2012