Search Documents

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By J. R. Hoskins

Method - A direct approach to instrument users, initially by letter and later by telephone or personal contact was made. The resultant data was compiled to give specific use information on the seven instruments. During the course of the study attempts to evaluate the Griswold Gage were abandoned when it became apparent that the gage was not being commercially produced. One company is developing the gage for its own use. The information presented is the result of over 1200 inquiries.

Jan 1, 1973

By Cloyd D. McDowell

The Federal coal Mine Health and Safety Act of 1969 has been criticized by those who say it goes too far in controlling the activity of private enterprise and by those who say it does not go far enough in eliminating fatalities and accidents in an accident prone industry. Possibly a better evaluation of this legislation lies somewhere in between. From the viewpoint of the coal industry it can be said that through the efforts of those engaged in mining, both the operator and the miner, the year 1969 marked a record year in mine safety with only 190 fatalities and a frequency of 0.84 per million man hours exposure. This outstanding achievement compared to any previous was the result of a determined effort on the part of a concerned industry to improve its reputation as being the most hazardous industry in the nation. After the effective date of the Act, March 31, 1970, the Bureau of Mines assumed complete control of all safety and health activities of the mining industry. Unfortunately, there was no improvement in the safety record of underground mines in 1970 with the total of 255 fatal injuries and a frequency of 1.04 for the year. The number of fatalities declined to 177 in 1971 but the number of underground coal mines had declined from 5,955 to 2,268 during the two year period. Meanwhile, surface mined coal increased from about 38% of total production in 1969 to over 50% in 1971, keeping the annual production of coal at a normal level but involving fewer men.

Jan 1, 1973

By David B. Brooks

I gratefully acknowledge the help of a number of American and Canadian geologists, in both federal surveys and in private firms, who took the time to discuss this problem with me. Hans Landsberg and Bruce Netschert also followed the study with interest and encouragement. In their 1961 monograph, THE FUTURE SUPPLY OF THE MAJOR METALS, Bruce Netschert and Hans Landsberg noted that identified potential resources (that is, known but submarginal resources) of lead and zinc were much lower relative to reserves (that is, known and supermarginal resources) than was the same ratio for other metals.1/ Put another way, it seemed that for such metals as iron, manganese, copper, and aluminum, slightly more favorable economic conditions or modest advances in technology would greatly increase reserves by permitting the exploitation of vest quantities of leaner or deeper or otherwise less valuable mineral deposits. But for lead and zinc, Netschert and Landsberg concluded that either: "(1) there is relatively little material below present cutoff grades; [or] (2) such material exists, but for some reason there are no data.? 2/ This situation, which they called "the lead-zinc anomaly" has been subsequently discussed by other authors. The purpose of this paper is to carry the discussion further by examining the evidence in favor of (1) and (2) and by advancing a third alternative.

Jan 1, 1967

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By Collon C. Kennedy, Frances C. Hartogh, C. Joel Casburn

INTRODUCTION During the nineteenth century, the federal mining law was enacted with the objective of promoting the development of the western United States by providing unrestricted access to vast areas of federal land for mineral exploration. Prior to the advent of comprehensive federal, state and local land use plans, there was little, if any, regulation or restriction of mineral exploration activities. Today, the laissez-faire policies of the past that encouraged mineral exploration have gradually given way to the public's legitimate concerns regarding environmental protection, multiple use and planned land development. As a result, the contemporary prospector confronts a maze of statutes, ordinances and regulations with which he must comply to obtain the requisite approvals and permits before commencing mineral exploration on federal, state or private lands. This presentation will provide a broad overview of the exploration permitting process. The first section of this paper recommends certain general management practices to follow when attempting to obtain exploration permits. The second section presents two hypothetical cases, one involving a drilling program on private property in California and the other involving a drilling program and the removal of a bulk sample for metallurgical tests from federal land in Nevada. The cases are used to discuss jurisdictional issues and application of certain federal, state and county laws and regulations that pertain to mineral exploration. The final section contains a brief analysis of three important recent United States Supreme Court decisions. These decisions address the scope of the federal pre-emption doctrine as it applies to activities conducted on unpatented mining claims and the constitutional limits of permissible state and local land use and zoning regulations. PERMITTING PRACTICES The environmental impacts associated with mineral exploration generally result from the construction of drill sites, roads or trenches. Consequently, after the regulatory authority has considered the issues of permissible land use, the primary emphasis of the permitting process is to address problems related to pre-construction site identification and clearance, and post-construction site reclamation. The approaches taken to address these and other related issues vary with the scope of proposed work, the site, the appli-

Jan 1, 1987

By F. Calizaya, M. G. Nelson

This paper presents a summary of basic requirements for the design, installation and operation of booster fans in coal mines, especially in deep and/or extensive mines. It includes a brief description of the major steps that should be followed to ensure that these units are used in coal mines safely and efficiently. The guidelines were prepared based on the standards and regulations adopted by two prominent coal mining countries, the best practices developed by the mining industry, and the applicable standards used in the United States for the fail-safe operation of main fans.

Jan 1, 2015

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By Shani Engelbrecht, Belinda McFadzean, Avuyile Wali, Natalie Shackleton, Vratislav Malysiak

Frothers play a crucial role in sulphide and PGM ore flotation recovery, and AECI Mining Chemicals studies on PGM ores have shown significant flotation kinetic increases with the optimal frother-collector combinations. Using Senfroth 200 as the industry baseline, remarkable kinetic increases were observed with AECI Mining Chemicals developed frothers in the first concentrate. Even in the worst-case scenarios, 4E PGM recovery increased by 5% at a slightly higher concentrate grade. It is important not to limit frother dosage to a fixed value. Instead, enough frother should be added to maintain a stable bench float, measuring the dosages by frother volume before and after tests. Frothers can be specialized blends and their importance should not be underestimated. The results produced by formulating and innovating frothers to address specific industry challenges have been encouraging. Testing a frother on a plant scale does not have to be as daunting as with collectors, enabling the identification of the best frother-collector combinations at an industrial scale. AECI Mining Chemicals bench scale testwork has motivated plant-scale trials that have successfully transitioned to commercialization. This paper compares the results from metallurgical and froth stability tests and shows that occasionally frothers that have a less stable froth can have improved valuable mineral recoveries, while still exhibiting better drainage for reduced entrainment and mass pull. It was shown that caution should be used when relying only on simplified froth stability tests in the evaluation of new frothers.

Feb 1, 2025

By Yi Luo

Subsurface strata movements and deformations caused by longwall mining operations in underground coal mines could affect many important coal mining activities, such as gob well degasification, ground water protection and multiple seam mining. The stratifications in the overburden have significant influence on the subsurface and surface movements and deformations in the ground subsidence process. An enhanced subsurface subsidence prediction model considering overburden stratifications has been introduced in this paper. In this method, the entire overburden strata are equally divided into a finite number of layers and the percent of the hard rocks in each layer is an additional input. The proven influence function method is applied to predict the subsidence on each of the predefined layers progressively upward using the predicted subsidence on the previous layer as the subsidence cause for the current layer. A computer program is developed to facilitate the calculations. A case demonstration is used to show the applicability of the proposed subsurface subsidence prediction model.

Jan 1, 2012

By W. G. Pariseau

A study of coal pillar strength at the Beehive Mine in central Utah was done in the 1970s. This study was a cooperative effort by the University of Utah, RE/SPEC, Inc., and the American Coal Company and was funded by the U.S. Bureau of Mines. Mine measurements of closure at 117 points and pillar stress using 119 vibrating wire stress gauges were made during retreat mining in this room-and-pillar operation. Laboratory testing for the strength and modulus of 372 coal cylinders up 0.3 m (1 ft) in diameter and 0.6 m (2 ft) in length was also done. Two-dimensional finite element model analyses complemented the study. However, the real world of mining is three-dimensional and in consideration of the significant advances in computing power since the time of the original study, a revisit of the data seemed warranted. In this regard, a novel finite element method was used that allows for the whole-mine analysis of tabular excavations on the kilometer scale and yet enables details to be obtained at pillar walls on the meter scale. The effects of material properties variability in situ and of joints can also be taken into account. Results that compare computed two- and three-dimensional seam-level closures with mine measurements show noticeable differences; three-dimensional results are reasonable, while two-dimensional results overestimate closure by nearly a factor of two.

Jan 1, 2014

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By Verya Nasri, Jaeseoung Lee, Ashish Bhargava, Shashank Gupta

This paper presents the unique design and construction challenges for the Technoparc Station, located in downtown Montreal as a part of Réseau Express Métropolitain (REM), a light rail rapid transit system. The station is located 15 m below the street with rock-bearing secant pile wall as the primary structural system working as both the retaining and gravity structure. The paper highlights the challenges related to the support of excavation structure, invert slab resisting high hydrostatic forces, waterproofing tightness etc. It also focuses on the importance of Building Information Modeling (BIM) in underground tunneling projects for effective coordination, clash-free, optimized design and costs.

Jun 13, 2021

By Neil Williams

The brecciated dolostone-hosted (Mississippi Valley-type) and associated shale-hosted stratiform Pb-Zn deposits at McArthur River occur adjacent to a major syndepositional fault, the Emu fault. Base-metal zoning, mineral parageneses, and Pb and stable isotope ratios indicate that both types of deposits formed contemporaneously from metalliferous brines that flowed into the host sediments from the Emu fault. Derivation of brines from underlying evaporitic sediments is suggested. Geochemical evidence indicates that the mechanism of ore formation was sulfate-reduction coupled with oxidation of organic matter. The textural relationships of stratiform sulfide mineralization to diagenetic dolomite concretions, chert blebs, volcanic glass shards, and inter-ore breccia beds, indicate that the reactions proceeded diagenetically within about 100 m of the sediment/water interface.

Jan 1, 1979

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By M. Kuchta, S. Iverson

INTRODUCTION Underground blasting with perimeter damage control can reduce the requirement for loose rock scaling and reduce the risk of ground-fall injury. In previous work Johnson and associates (2010) from the National Institute for Occupational Safety and Health (NIOSH) developed a rock blasting perimeter damage and control design method included in the DRIFT software tool (NIOSH, 2018). This blast design software tool utilizes current methods of perimeter blasting with the added design element of a buffer row coordinated with the perimeter row to reduce perimeter damage. The coordination is in applying one of several blast damage models to calculate the damage extent for each production, buffer, and perimeter blast hole in the design. The calculated damage is then applied to the spacing between the blast holes. The basis of the buffer row design is the practical damage limit and is supported in this paper with computer models of signature blasts and full blast rounds using PFC2D (Itasca Consulting Group, Inc., 2018). Practical damage limit The practical damage radius (Rd) is not to be confused with burden. The practical damage extends toward the burden side and inward into the rock mass. For all practical purposes, the practical damage radius equals one half the burden (Hustrulid, 1999). The maximum extent of radial crack damage around a blast hole (Rcrack) and the maximum extent of radial crushing damage (Rcrush) are illustrated in Figure 1. A “practical” radius of damage (Rd) lies between the crushing limit and the cracking limit. The “practical” damage means that if the rock mass lying outside of the practical damage circle were removed, the rock remaining within the circle would easily break apart. Blast pressure and strain Work by Johnson (2010) and associates included signature blast tests in large concrete blocks. A signature blast test in concrete as exampled by strain data in Figure 2 was designed to monitor the dynamic strain at incremental distances from a single fully coupled blast hole, measure crushing and radial cracking extent by wire-sawing to expose the damage, and relate the damage to overbreak that is common in underground blasting. The initial slope or rising strain as the stress wave passes by the strain gages shows very high strain and strain rates close to the single blast hole. Since the derivative of strain versus time is strain rate, a line tangent to each of the strain curves at the maximum strain rate is drawn and the strain rates identified. The high strain rates were then plotted on a semi-log in Figure 3 to show a linear trend. The strain rate is greater than 100 s-1 within 20 cm from the blast hole for the signature blast experiment. The strain rate at the blast hole wall is projected to be 300 s-1. Figure 4 illustrates the damage in the NIOSH block exposed by a wire saw cut.

Jan 1, 2019

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By N. Duru, C. Nesbitt

During the cyanide leaching process, gold and silver ores that come from the transition zones, which typically contains low levels of sulfide, may produce one or more of the following reduced sulfur species: sulfide ( HS−), polysulfides ( Sn 2−), thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−), pentathionate ( S5O6 2−), hexathionate ( S6O6 2−). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the redox potential, pH, cyanide levels, and existing sulfur species in recycled process water, as well as the presence of other reactive metal species. The development of an accurate analytical method for sulfur species in cyanide leaching units of gold ores where sulfur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and the development of ion chromatography method to analyze reduced sulfur species thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−) in cyanide leaching circuits for gold ores. The method developed has resulted in precise quantification of target sulfur species in leach solutions. Method development and validation results were illustrated on analytical graphs containing each species’ peak number, retention time (min), type, width (min), area (mAU*s), height (mAU), and area distribution (%) of the peak.

Mar 2, 2024

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By Cengiz Karagüzel, Ömer Canıeren

The mobility of gold and silver metals from refractory ores is very low due to free metal ions in their bodies that bind the transportable and free metal molecules or they are encapsulated in minerals such as sulfides, arsenosulfides, carbonaceous, and clayey materials which make it difficult to extract them. As known from the literature, the enrichment of oxide refractory gold, silver ores, Ag, and Au-rich flotation concentrated from sulfur refractory ores can be leached in the chloride-hypochlorite solutions. In this work, the leaching approach was studied to extract silver ions from refractory ores in the presence of hypochlorite media under high pressure. The mineralogical and scanning electron microscopy analysis of the sample indicated that the silver was encapsulated in barite and quartz minerals in fine sizes. In order to obtain the optimum leaching conditions for the silver ore, the effects of several parameters, namely, temperature, leaching time, NaCl and NaOCl concentration, solid ratio, and particle size on the leaching recovery were investigated in detail. The leaching experiments showed that the highest silver recovery of 62.35% was obtained under the following conditions: temperature of 150 °C, oxygen pressure of 1800 kPa, leaching time of 2 h, concentrations of 2 mol/dm3 and 0.4 mol/dm3 for NaCl and NaOCl, respectively, the solid ratio of 30%, and particle size (d80) 15 μm. The results obtained from this study indicated that the enrichment of refractory silver ores to extract the silver encapsulated in barite and quartz minerals could be possible in the chlorite-hypochlorite under high pressure, a relatively shorter leaching time compared to conventional cyanide leaching.

Jan 28, 2021