Search Documents

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By John L. Bolles

The Phelps Dodge Corporation's Morenci Concentrator includes facilities for coarse crushing, fine crushing, grinding, flotation, tailing, disposal, concentrate filtering, and drying. The Morenci Concentrator daily throughput is in excess of 60, 000 tons. The ore milled is mainly a medium-hard monzonite porphyry in which the principal sulfide minerals are chalcocite and pyrite. The ore is transported by rail from the Open Pit Mine to the primary crushing plant located at the concentrator site. Ore is side-dumped from 80¬ton railroad cars into a sixty-inch gyratory crusher. The ore is then conveyed to a. 12, 000 ton coarse ore storage bin. Fine crushing is accomplished by four parallel lines of conventionally stacked crushers in open circuit. Each unit consists of one seven-foot standard cone followed by two seven-foot shortheads. Ti% product of the fine crushing plant is distributed by two tripper cars across a fine ore storage bin. The crushed ore is then fed by variable speed belt feeders into thirty parallel, single stage, closed circuit grinding units. Each of the 30 grinding units consists of one 6' x 23' conditioning drum, one 10' x 10' ha l mill and two 54" duplex spiral classifiers as principal equipment. The dry ore is fed into the conditioning drum with water to dilute the ore to a slurry of approximately 78% solids by weight. An aqueous solution of ammonium sulfide is also added to the conditioning drum. The ammonium sulfide primarily acts as a sulfidizing agent. The ore slurry containing the naturally occurring sulfide copper minerals and the sulfidized copper minerals discharges into the feed scoop box of the ball mill, where milk of lime, collector and-.dilution water are added. The ball mill product slurry is gravity fed: to the classifier pool where water is added to obtain the desired classifier overflow product

Jan 1, 1977

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By Dennis Asmussen

The peatlands of the U.S. and Canadian parts of the Upper Great Lakes region have a long history of modest utilization in agriculture, forestry, horticulture, and as natural undisturbed areas. Only recently have they been assessed as potential sources of non-renewable or renewable energy. This new interest in peatlands, should current proposals be realized, might mean the commitment of millions of acres to energy production purposes. The magnitude alone of this potential utilization of peatland signals the possibility of substantial environmental disturbance, local resource shortages, resource use conflicts, and social and economic change. Peat- land resource managers in the region are just beginning to weigh the advantages and disadvantages of large-scale peatland utilization. The Minnesota Department of Natural Resources has made a considerable effort to study peat resource management issues and will shortly make recommendations to the state legislature regarding utilization alternatives. What follows is a general discussion of peatland utilization and management trends in the region with a focus on Minnesota and its peatland management efforts.

Jan 1, 1980

By M. A. Trevits

The explosion hazard presented by methane gas in coal is confronted daily in the mining industry. Research has developed several viable methods for gas control in addition to conventional dilution by ventilation. Such methods include the drilling of horizontal or cross-measure boreholes from a mine opening and vertical boreholes hydraulically stimulated in advance of mining or for gob gas drainage. The long-term production history of five gas drainage installations was studied. Three installations were completed in the Pittsburgh Coalbed: two in West Virginia and one in Pennsylvania. The remaining installations were completed in the Mary Lee Coalbed in Alabama and the Sunnyside Coalbed in Utah. The types of drainage methods utilized included horizontal and vertical boreholes. The length of production studied ranged from 860 days to 36 years. The cumulative production from the five sites was in excess of 155 Mm3, representing a significant volume of gas.

Jan 1, 1985

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By L. M. Litz

The results of a study are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 parts per million. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that were concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1980

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill's approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By J. A. Herbst, H. R. Cooper, R. J. Brison, R. W. Harper, K. P. Ananthapadmanabhan, W. C. Hellyer, B. H. Bergstorm, D. M. Hopstock, H. Rush Spedden, W. C. Hellyner

Scope of Section The physical characterization of an ore or mineral mixture in such detail that mineral processing may be effectively applied to create more useful products is one part of the technology of sampling and testing. In addition, the evaluation of the multitude of separation processes, both physical and chemical, combined with ancillary opera¬tions and performed on samples at a laboratory scale, is another part of the testing procedure. Although analytical techniques provid¬ing quantitative determinations of elemental compositions are an im¬portant and necessary supplement to any testing program, that field of endeavor is a well-developed, separate entity beyond the scope of this Section. Sampling procedures cover the practice of selecting representative quantities of test materials in the field to evaluate mineral deposits, and extend to techniques of obtaining process samples in slurry and bulk ore as part of process evaluation. The same techniques are appli¬cable, of course, to standardized methods of metallurgical accounting. Sampling is also an important facet of successful on-line measurement of slurry properties such as assays and particle size in the practice of automation. However, the sampling methods in this case can be different from those needed for precise testing and accounting pur¬poses. Sampling was well defined in Taggart's Handbook as "the opera¬tion of removing a part convenient in size for testing, from a whole which is of much greater bulk, in such a way that the proportion and distribution of the quality to be tested (e.g., specific gravity, metal content, recoverability) are the same in both the whole and the part removed (SAMPLE). The conditions of the more stringent definition, that the sample shall be completely representative of the whole as regards all aspects save bulk, are practically never fulfilled when heterogenous mineral mixtures are sampled." Taggart's Handbook of Mineral Dressing, Section 19, "Sampling and Testing," continues to be a very useful compendium of principles and techniques, particularly as applied to manual methods for han¬dling samples. In the intervening years since its last revision, substan¬tial progress has been made in both the theory and the techniques; thus, this current contribution is designed to be an extension of the earlier work, yet complete enough to provide procedural guidelines to methods of continuing validity. Although basic principles of testing remain unchanged, the meth¬ods of applying those principles have undergone great change. New testing equipment has become available, yielding a greater precision of results. Testing methods have been refined which, in many cases, allows for a valid scale up of flowsheet designs without the necessity of costly pilot or prototype plant development. Justification for a Sampling and Testing Program* The proper evaluation of a mineral property is a complicated process. It often is done on a team basis with the exploration geologist, mining engineer, mineral process engineer (extractive metallurgist), economist, and product utilizer (ceramist, chemical engineer, chemist, metallurgist, etc.) all represented. The mineral processing engineer is a key member because he can provide a go no-go answer to the question, "Can this ore be processed economically?" In addition, his judgment on the response of even the initial sample to processing can be an invaluable guide to the proposed process and its mutations. Since the capital investment and operating costs are so sensitive to the type of process used, the judgment of the mineral processing engineer forms an important part of the early evaluation of the profitability of a new mining venture. This early estimation of the processing approach is all the more important since, for some metalliferous ores, the capital investment for mill, smelter, water supply, and tailings disposal exceeds the cost of the mine. At present, for commodities such as coal, the reverse is true. There is a smaller capital investment for the coal preparation plant than for the mine. In general, both the capital and operating costs escalate very rapidly in the following order: gravity concentration of alluvial deposits (e.g., dredging), gravity concentration of lode ores, flotation, simple hydrometallurgical processes, and complicated hydrometallurgical and pyrometallurgical processes. The latter two processes may cost 100 to 1,000 times more per ton treated than processing of a simple alluvial deposit. This dictates that the valuable mineral be concentrated as much as possible to minimize the total tonnage treated in the more expensive operations. Within each of these ore-processing categories there is a wide range of process sophistication and hence of capital and operating costs. Perhaps the greatest variations are in the chemical processing of ores. These range from the simple leaching of a copper waste dump to very sophisticated hydrometallurgical processing of ores in increasing order of cost. Because the overall cost of a mining venture is so sensitive to the process selected, it is essential that the mineral¬ processing engineer evaluate the ore in the initial stages of the development of an ore body. As better samples become available, he must continually revise his estimate of the process to be employed. The sampling and testing process must be a necessary and continuing activity throughout the life of a project. One fundamental aspect of nearly all mineral deposits is the inherent variability of the mineral assemblage and composition. A utopian goal of any processing plant is to have the process so flexible and so well-defined that an automatic process control system can optimize the economic recovery at all times. Since this is rarely possible, a continuing or at least a periodic testing program is desirable. Variables to be considered are: 1) Ore body inconsistencies. 2) Zonal variations. 3) Feed variations from mining plan or methods. 4) Variable performance of processing units due to wear. 5) Seasonal or other changes affecting processing conditions such as water quality, temperature, etc. 6) Changing market conditions for product quality or byproducts. 7) Technological advances in processing methods or equipment. 8) Increasing demands for environmental control. 9) Changing economics of competitive processes, of supplies, of capital investment vs. labor costs, etc. Sampling Procedures Preliminary Guidelines for Sampling Ore Deposit Studies. t At a very early stage, it is essential that the mineral processing engineer receive a sample of the ore. This may be a portion of the diamond drill core or a split from the trench, pit, churn drill, channel, or sheet sample. Even a grab sample may have some value, but it should be selected by the mining engineer or exploration geologist to be as representative of the ore body as possible within his best judgment. The sample delivered to the process engineer should have been subjected to as little prior crushing as is practical since fine sizes are difficult to concentrate. In addition, finely ground ores are readily oxidized and thus may give misleading test results. Furthermore, ground samples may make it impossible to eval¬uate either the comminution or the coarse-gravity concentration pro¬cesses. For an initial evaluation, a good deal may often be learned from a sample of only a few pounds if that is all that is available. To obtain the maximum information from a sample, its selection should be carefully discussed with the mineral processing engineer. In addi¬tion to being as representative as possible, the mineralogically distinct samples should be carefully segregated rather than composited. Since drastically different processes are often needed to process samples of differing mineralogy, considerable care and time must be exercised during this sample collection step. The segregation of samples showing gross mineralogical differences, such as the oxide caping on a sulfide deposit or a laterized zone, is easy. It is the more subtle changes in mineralogy that can often elude the field man. Yet these differences are often sufficient to dictate that an entirely different type of process be used. Obviously, the selection of these initial samples for ore testing and mineralogical studies requires that it be done by a man of consider¬able experience and judgment. While the mining engineer or field geologist is collecting these samples, he should also note and convey to the processing engineer such details as water quality and availabil¬ity, terrain, potential mill location, tailings-disposal areas, case of transportation, etc. As the property is developed with additional drill holes, adits, etc., larger and more representative samples will be required to develop the ore-processing flowsheet more adequately. If pilot-plant studies are required, a very large sample may be necessary. Though the type and amount of sample collected for flowsheet development investigations vary widely, gathering a representative sample of the ore body is a prime requisite for any process development effort. The process developed for any given ore body is only as reliable as the sample on which the flowsheet was based¬

Jan 1, 1985

By John A. L. Campbell

Surface dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or imporve a surface dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and flocculation. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established (1). These data will be presented at a latter date.

Jan 1, 1969

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Leon D. Keller

Hydraulic concentration of minerals has been practiced for a good many years. Until recently, however, the practice has been limited to a multiplicity of small pockets and relatively low tonnages and flows. The adaptation of the SiphonSizer to the concentration and classification of magnetite has changed this concept. Some fifty commercial units are currently in operation on magnetite, varying in size from 16 ft diameter circular unit to a 25 ft by 100 ft rectangular unit. Additional units up to 38 ft diameter are under construction. Depending upon the application in the flowsheet, upgrading-varies from 0.75% to 14% Fe in a single stage. To those not familiar with taconite processing, the importance of the struggle to economically remove as much silica as possible may not be fully appreciated. These figures pertaining only to transportation may be thought-provoking. If a 10,000,000 ton per year plant could reduce the silica content of their concentrate by 17, a savings in boat freight alone would amount to 100,000 tons at $2.00 per ton annually.

Jan 1, 1963

By Ewald H. Kurt

The story of America's progressing standard of living is the story of machines. The automobile, the airplane and the telephone for example have made our transportation and communication systems what they are today. Even they depend in turn on another machine -- the rock drill. By making it possible to economically mine and quarry minerals in large quantities, this versatile machine supports virtually every American industry relying on the earth for its buried raw materials. And, like all machines, the rock drill's mechanical evolution was stimulated by production demands placed upon it. All percussion drills are mechanized versions of the original drilling unit -- man, Figure - illustrates a double jack team at work before the turn of the century. The man with the sledge hammer is the impact device while the man sitting is the rotation mechanism and feed motor. The first drifter drills (Figure 2) performed the same function but with increased mechanical efficiency. A piston controlled by a valve produced impact. A built-in ratcheting mechanism provided rotation and a hand-cranked screw provided feed thrust. As the industrial revolution proceeded into the twentieth century, the demand for raw materials stimulated refinements of all recovery machinery, including rock drills. As drills became heavier and more powerful, a mounting (or carrier) had to be provided to move the drill from hole to hole. This resulted in the development of the wagon drill (Figure 3). Propelled by muscle power, the wagon drill was for years the standard tool of the surface drilling industry (Figure 4). As drills penetrated faster and as labor increased in cost, the time consumed in nondrilling peripheral operations had to be

Jan 1, 1977

By Charles N. Speltz

The cost of transportation of industrial minerals frequently is higher than the cost of the product. When a mine, industrial-mineral plant, or customer is served by a single railroad, because of the lack of competition, that railroad may in- crease rates and/or reduce service so that the economics of that mine, plant, or customer are affected adversely. Transloading of industrial minerals from rail-to-truck or truck-to-rail to improve economics and sales of product is not a new concept. However, transloading to create competition and reduce freight costs or to improve service is a relatively new concept brought on by the recent mergers of many of the main-line railroads, both in the eastern and western United States. For example, in 1998, with completion of the Burlington Northern/Santa Fe (BNSF) and the Union Pacific/Southern Pacific mergers (UPSP), the western United States has only two main-line railroads. The industrial-mineral producer, to reduce the cost of transportation or increase the level of service, must evaluate potential transloading opportunities in light of higher prices and reduced service brought on by reduced railroad competition. This paper discusses industrial-mineral transloading and examines the case history of the Tucker Hill perlite project in southern Oregon. The Tucker Hill project is a classic study of industrial-minerals transloading where the project would have failed without the transloading.

Jan 1, 1999

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By Eugie Kabwe

The effective employment of a pretensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut preload. In this paper, a load indicator washer (LIW) able to withstand an assigned static loading as well as provide an appropriate pretension is presented. The different LIW breadths are numerically analyzed with ABAQUS finite-element code to estimate deformation when a designated 60 kN preload is applied. The numerical simulation employs the bilinear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nut-LIW-rock bolt connection. Therefore, long-term relaxation effect on bolt pretension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW predetermined deformation is the bolt pretension. It is drawn from the simulation results that LIWs with thicknesses of 1.5, 2.0, 3.0, 3.5 and 4.0 mm are completely flattened when subjected to 28, 42.5, 65, 76 and 88 kN preloads, respectively.

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997