Search Documents

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By Kai Koosmen, Mehdi Serati, Tengzhou Wang

Spalling and rockburst are unwanted brittle failures at the boundaries of underground excavations that are commonly observed in hard rock and high-stress environments at significant depths, although, spalling has also been observed in comparatively shallow soft rocks. The crack initiation (CI) stress threshold (representing the stress level at which new micro cracks begin to form in an intact rock) is widely used to establish the in-situ spalling strength, and is generally regarded as the lower limit of the long-term rock strength. This study analyses the evolution of CI and other mechanical properties for a high-porosity sandstone with an average UCS of 38 MPa under unconfined cyclic compressive loading. The results indicate that rock properties are variably affected by cyclic loading with; no significant effect on Youngs Modulus; a moderate increase in Poisson’s ratio and fracture angle; a moderate decrease in UCS; and a major reduction in the CI stress threshold. All of these changes were generally amplified by cyclic loading at higher stresses. From the results, it is concluded that rockburst and spalling limit in underground structures may reduce over time if the rock is subject to repetitive cyclic loading, and that the reductions will be greater for higher cyclic stresses. This may be a significant factor in the design and operation of some deep underground structures.

Apr 26, 2022

By R. R. Klimpel

The use of froth flotation as a means of separating and upgrading sulfide mineral concentrates is standard industrial practice throughout the world. It is ap-parent from observing the industrial practice of sulfide mineral flotation over the last decade that progress is being made in optimizing the operating aspects of flotation. Examples of this are the availability of improved instrumentation and related computer control devices, the modification of mechanical flotation cell designs, the introduction of column cells, better reagent dosage control, blending of feed ores, increasing attention to coarse and fine particle separations, the successful introduction of new frother chemistries, etc.

Jan 1, 1989

By Tania Schmid, Marco Portal Valdivia, Sandra Nowosad

Today’s mining industry faces rapid transformation driven by automation, climate responsibility, and ESG demands, requiring more than technical expertise. Future mining engineers must blend engineering excellence with key human skills such as communication, leadership, resilience, empathy, adaptation to change, curiosity and lifelong learning. Based on two recent surveys, one to senior leaders with over ten years of experience in the mining industry and a second, focused on understanding the perceptions of young professionals, this paper explores which skills become core competencies by 2030 for navigating complexity, leading responsibly, and enabling sustainable transformation. Furthermore, it also examines how educational institutions can adopt strategies to foster the development of these critical skills, preparing future mining talent for evolving challenges.

Feb 22, 2026

By R. J. Jula

The process of treating granular activated carbon for return to service in the recovery of gold in Carbon in Pulp and Carbon in Leach circuits has been investigated. Carbons from four U.S.A. mines, one Canadian mine and one South African mine were characterized before and after regeneration. The use of thermal gravimetric analyses demonstrated the presence of inorganic compounds on the surface of the carbon. Thermal regeneration was investigated using factorial' analysis to determine the effect or interaction of furnace temperature, retention time and the use of supplemental steam. The operation of acid leaching prior to or after gold elution was investigated. The effect of water quenching, regenerated carbon was also studied. From the data obtained in this investigation, guidelines are given for effective regeneration operation.

Jan 1, 1985

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION The two unit operations in cut-and-fill stoping that would benefit most from increased mechanization are drilling blastholes and moving broken ore to the ore¬passes. Drilling in current practice is done with hand¬held jackleg and stoper drills. Broken ore is commonly moved from the face to the orepass by a small slusher. This type of equipment can be easily moved through the raises. Hand-held drills have a slow drilling rate and require one operator for each machine. Drilling can be done much faster by small jumbo-mounted machines as two or more drills can be operated by one miner. Load-haul-dump (LHD) units move broken ore from the face to one or more orepasses at a much faster rate with less loss and dilution than slushers. These units are mobile and may be used at more than one place during a shift. The problem which must be overcome in applying this higher degree of mechanization is the restricted means of access inherent in current practices. Cut-and¬fill methods are usually applied to mining veins that are narrow, irregular in dip and strike, or where ground con¬ditions require the support of sand fill. The mechanized equipment which is needed to accomplish high produc¬tion cannot be raised or lowered through raises without being disassembled. A jumbo which will give the desired performance would be mounted on a rubber-tired carriage with a diesel engine for propulsion. Twin hydraulic booms run by a small air motor would carry pneumatic drills. Over¬all dimensions of the unit would be about 8 m (26 ft) in length, 1.6 m (5'/z ft) in width, and 1.6 m (5'/z ft) in height. An LHD of the desired capacity would be rubber¬tired and either diesel or electric-powered. The overall dimensions of a 2.3-m (3-cu yd) unit will be about 8 m (26 ft) in length, 1.8 m (6 ft) in width, and 1.5 m (5 ft) in height. It will weigh about 12 700 kg (28,000 1b). It can readily be seen that conventional raises can¬not handle this size equipment. The most desirable means of access enables equipment to be driven into the stoping areas. Ramps can enter the stope by being driven upward in the vein walls or by being developed in the vein on top of the fill as the stope advances. This ramp system not only permits the use of rubber-tired equipment in multiple working places but also enables its removal for repairs without component breakdown. In the proposed method, as in conventional cut-and¬fill stoping, sand fill will replace the mined-out ore. By constructing an inclined timber floor at one end of the stope, a ramp can be maintained on top of the fill and advanced as the stope is advanced cut by cut (Fig. 1). The ramp is, therefore, developed during the stoping process and is only driven as a tunnel when rising over and around the sill and crown pillars. A stoping section consists of three blocks of different geometric shapes. The first and last blocks to be mined will be triangular in the plane of the vein, and the blocks between will have the shape of parallelograms (Fig. 1). The first block will develop the initial ramp by breast stoping and filling to the ramp floor (Fig. 2). The ramp will need to be completed through to the next level be¬fore stoping of the subsequent block can begin. The subsequent blocks are mined by back stoping with the next ramp being developed at the other end of that block (Fig. 3). The length of each subsequent block can be varied without changing the slope of the ramp. As the new ramp is developed, the previous ramp is filled along with the stope cut. Access up and down is maintained through the stope. The final block is again breast stoped as no new ramp will be developed at the end line for jumbo egress. Boreholes provide ventilation between levels as well as utility access. They can also provide a secondary escapeway for personnel during periods of development. These boreholes would be located about 3 to 4.5 m (10 to 15 ft) in the footwall and spaced about 183 m (600 ft) apart along the vein. The orepasses are spaced about 61 m (200 ft) apart in the vein. This spacing allows not only a short tram for the LHD unit but also provides surge capacity for the ore between haulage trains. These passes are raised from the haulage levels. As development progresses, the raises are driven through the sill pillar, and then car¬ried in the fill as stoping progresses. Ventilation and utilities can be maintained through an orepass when it is not needed for ore. The end line orepasses are intended for this purpose as well as for personnel emergency egress. Overall dimensions and criteria assumed to illustrate the ramp method of access in a highly mechanized cut¬and-fill stope are: haulage level spacing of 61 m (200 ft); ramp gradient of 17%; average dip of approximately 1.57 rad (90°); initial stope length of 358 m (1177 ft); subsequent stope length of 179 m (588 ft); average stoping width of 3 m (10 ft) ; sill pillar thickness of 3.6 m (12 ft); crown pillar thickness of 1.8 m (6 ft); bored raises of 1.5-m (5-ft) diam; and cribbed orepasses of 1.2 x 1.2 m (4 x 4 ft) through the sill pillar and 1.2 m (4 ft) square inside the cribbed portion. DEVELOPMENT The ramp access system lends itself well to conduct¬ing the several phases of development concurrently. Haulage Drifts and Raises The first development step will be to drive the 3 x 3-m (10 x 10-ft) haulage drifts above and below

Jan 1, 1982

By Zhongwei Wang, Dong Wang, Feng Ju

The coal seam in the southern coal field of the Ordos Basin serves as the main aquifer, while the region is known for its high-intensity coal mining activities. The coupling effect of mine water and the strong disturbance caused by high-intensity mining have brought serious challenges to the stability of coal pillars. To address this, a formula for determining the reasonable width of coal pillars under the aforementioned coupling effect and establish a criterion for coal pillar instability in this paper. A case study was on the 11,215 working face at the Xiaojihan coal mine in the area to investigate coal pillar stability. Results indicate that the strength and stability of the coal pillar are affected by the water content, with a small water content increasing its strength and large water content weakening it. In high-intensity exploration of watery coal seams, the best stability of the coal pillar is achieved at optimal water content and mining rates. For the Xiaojihan coal mine, the optimum water content and mining rate are 3.31% and 20 m/d, respectively, ensuring the efficient mining of watery coal seams. Furthermore, this study's findings can provide valuable references for the mining design of coal mines with similar geological conditions in the region.

Feb 13, 2024

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

At long last, mining is on the rebound in Minnesota?s Iron Range and the excitement is starting to show. The SME Minnesota Section?s annual meeting was once again held in the heart of Iron Range country, at the Duluth Entertainment and Conference Center on the Duluth waterfront. The conference boasted a record attendance of 475 people and its largest-ever trade show. Appearances by Governor Mark Dayton?s new Iron Range Resources & Rehabilitation Board (IRRRB) appointee, Tony Sertich, as well as a local Fox news crew (see clip on SME website [link: http://fox21online.com/news/duluth-mining-conference-breeds-optimism-tech-innovation]) made clear that a lot of eyes [ ] are on the industry as it dusts itself off from the 2008-2009 recession. While the early years of the 21st century were very good to the Iron Range, the global drop in commodities prices and production left many companies reeling and brought back bad memories of the collapse of the industry in the 1980s. However, two years of solid growth and a rebound to above pre-2008 production levels have let the Minnesota mining industry to relax a little and talk seriously about long-term growth and stability.

Jan 1, 2011

By Mahamuda Abu, John Kalimenze, Benatus Norbert Mvile

The central Dodoma region of Tanzania is one of the regions defined by the Tanzania Craton (TC). Although the Craton gold mineralization has been well explored and hosts most of the gold deposits in the country, the understanding of the mineralization potential of the Dodoma region is still an enigma. This study using trace elements geochemistry of soil samples aims basically at providing information for future exploration works in the region by delineating the possible mineralized zones, the pathfinder elements, and the lithological facies to target. Generally, there is an anomalous spatial distribution of a probable Cu-Au deposit in the N, NE, S, and SE parts of the region and are prospective areas worth exploring for gold from the Gaussian variogram models. The multivariate statistics shows that Cu, Pb, Zn, and Fe are the main pathfinder elements while searching for Au mineralization in the region. The gold deposit is most probably a Cu-Au porphyry type, although VMS type of Au deposit cannot be precluded in the area. The mineralization in the area is largely associated with tonalitic orthogenesis, tonalities, granodiorite, and granitic rocks with Cr-Ni-Co-V forming elemental association. This elemental association is similar to other gold bearing greenstone belts. The style of mineralization in the Dodoma region is similar to other gold deposits within the TC; hence, successful exploration methods in these ancient gold deposits like Geita and Kahama gold deposits can be adopted in the event of any further exploration exercise in the central Dodoma region.

Jul 12, 2021

Improvements in cost efficiency, noise control, environmental design and ergonomics ? the mining and construction industries are facing demands on many fronts. The international manufacturers of construction machinery are responding to these challenges, and they will be presenting their innovations in all these fields at bauma 2013. bauma, the international trade fair for mining and construction machinery, mining vehicles, and building material machines, takes place from April 15 to 21, 2013 at the Messe Munchen exhibition center in Munich, Germany. The last bauma, in 2010, attracted 3,256 exhibitors from 53 countries, and more than 420,000 visitors from more than 200 nations. Covering a total of 555,000 m2 (5.97 million sq ft) of exhibition space, bauma is one of the largest trade shows in the world. This year?s fair is expected to surpass the 2010 figures. Here are some examples of the new developments visitors can expect to see at the show.

Jan 1, 2013

By Caroline L. Herzenberg

Recently, neutron-induced gamma spectrometry has been introduced and gained provisional acceptance as a method for continuous automated analysis of coal. Instrumentation based on this technique has been under development for and in testing at coal preparation plants and a coal gasifier. To provide a deeper understanding of, and extended capability in applying this method, theoretical calculations have been performed of the absorption of thermal neutrons by various coal compositions, and the thermal neutron capture prompt gamma emission spectra produced by these compositions have been calculated. Selected results of these computer calculations and the computer generated spectra are presented.

Jan 1, 1984

By Gary A. Nowlan

The Casa Grande West-Santa Cruz porphyry-¬copper deposit is in the Basin and Range physiographic province west of Casa Grande, Arizona (Fig. 1). The Casa Grande West portion of the deposit is controlled by Casa Grande Copper Company and the Santa Cruz portion by ASARCO. The deposit contains at least 350,000,000 metric tons of rock with greater than 1 percent Cu. The deposit is covered by at least 300 m of sediment, with no visible expression of the deposit at the land surface. The deposit is in an area of prime agricultural land that depends heavily upon well irrigation because of a hot and arid climate. Because of the deep sedimentary cover, the chance is extremely remote that the geochemistry of soil or stream sediment would reflect the deposit even if the land surface were not disturbed by many years of farming. Irrigation wells of the area generally bottom in the sedimentary cover. The purpose of the study is to see if the Casa Grande West-Santa Cruz deposit is geochemically reflected in ground waters over and near the deposit.

Jan 1, 1981

By D. D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a cost-effective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Feb 23, 2014

By Frederic Chavan, Hans Jakob Windier, Shane Yanagisawa, Willy Ritz

The Zurichberg twin track tunnel is the main segment of the Swiss Federal Railway's new expressline. A heavy concrete lining with a circular cross-section was chosen to cope with the swelling tendency of the surrounding rock. The 4,356 m (14,300 ft) long, 11.52 m (38 ft) diameter tunnel was driven using a shielded Robbins TBM. A 1.20 m (4 ft) wide, 25 cm (10 in) thick precast lining was placed from within the shield tail as the excavation progressed. Tunnel excavation and initial lining operation were completed in 18 months, averaging 11.86 m/day (40 ft/day) in two nine hour shifts. After breaking through, the final 28 cm (11 in) thick concrete arch lining was cast in place.

Jan 1, 1989

By T. C. Murray

An automatic control system was recently installed to insure the continuity of operation between the ship docking and ore handling facilities and the computerized conveyor-fed sintering plants and blast furnaces. Although the basic concept for material handling has not changed, many innovations including computer control have been implemented.

Jan 1, 1978

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By John Turner, David Carey

The Robbins Mobile Miner demonstrates the successful combination of hard rock excavation technology and the latest electronic control technology. The mobile miner, a partial face hard rock tunneling machine, features a fully integrated control system relying on a Programmable Logic Controller (PLC). This PLC controls all functions: tramming, steering, boom swing, cutting depth, conveyor operation, air scrubbers, hopper loading and unloading, etc. The machine is fully instrumented allowing the PLC to monitor the results of all commands on a continuous basis, to record data, to evaluate developing problems, or to shut the machine down if necessary. The paper describes the development of the Robbins - Pasminco automated mobile miner and early testing at Pasminco Mining&apos;s Broken Hill Southern Operations, New South Wales, Australia.

Jan 1, 1993

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022