Search Documents

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By L. Clark

Despite near-record commodity prices, the mining industry continues to search for ways to maintain profits in these times of steadily increasing energy prices and steadily decreasing grades. The pressure is still on today’s miners to continuously improve their operations because they know that one day prices too will drop. Some, however, have seized the opportunity to employ systematic methods to reduce costs and increase the efficiency of their workforce and equipment. As a result, closer attention is being paid to scheduling and the value that could be added by defining the extraction sequence that maximizes the net present value [NPV] of a project. This paper will discuss the challenges faced by Newmont Mining Corporation [Newmont] at its operations and the application of sophisticated software tools and methods in its search of solutions to this problem.

Jan 1, 2007

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By Rodney K. Morrison

MARTA, The Metropolitan Atlanta Rapid Transit Authority, is building a 53 mile heavy rail transit system to serve the City of Atlanta. Phase A of the Rail System, consisting of approximately 14 miles of at-grade, aerial and subway construction is underway. Metropolitan Atlanta lies in the Piedmont Geologic province of Georgia and is underlain by rocks of essentially granitic and gneissic nature. The soils encountered are primarily silty sands which are in-place weathering products of the parent rock and exhibit their relic structure. In general, these materials have presented no unique construction problems other than those created-by proximity of manmade structures, local availability of ground water, and top of rock elevation. The subway sections of primary interest in this paper consist of hardrock and soft ground tunnels and extensive cut-and-cover sections. The cut-and-cover construction includes excavations as deep as 80 feet. Temporary support systems in these deep excavations consist of soldier pile-timber-lagging or soldier pile-tremie concrete (SPTC) walls with internal bracing or tiebacks. In shallow cut-and-cover sections, where right-of-way economics permitted, slopes were laid back partially or fully to reduce or eliminate the need for bracing systems. Dewatering systems were required in most open cut excavations. Due to the close proximity of utilities and existing structures to the MARTA

Jan 1, 1979

By Edward (Ted) Dowey

City Water Tunnel No. 3 is being built in order to provide a redundant system for delivering 4,542,500 m3 (1.2 billion gallons) of water per day throughout the five boroughs of New York City. The present tunnels, City Tunnel No. 1 and 2 (Figure 1), were put in service in 1917 and 1936 respectively, and both have been in continuous service. Tunnels No. 1 and 2 can-not be shut down for inspection or repair until City Tunnel No. 3 has been completed. City Tunnel No. 3 has two stages (Figure 1).Stage One is 20.1 km (12.5 mi) long and is presently delivering drinking water to the boroughs of the Bronx and Manhattan. Stage Two consists of the Brooklyn-Queens Tunnel 17.7 km (11 mi) and the Manhattan Tunnel 14 km (9 mi). The Brooklyn-Queens leg is complete and is set to be put in service soon. The Manhattan Tunnel is being constructed and is the subject of this paper. The Manhattan Tunnel (Figure 1) is comprised of three legs: the north, south and east legs. The con-tract includes the excavation of 8,976 m (29,500 ft) of tunnel and the lining of 14,561 m (47,773 ft) of tunnel. The south tunnel, 5,705 m (18,720 ft), was excavated but not lined, under a previous contract. The tunnel ranges from 181 m (600 ft) to 152 m (500 ft) in depth in the bedrock under Manhattan. The tunnel contract also includes the construction of nine new shafts, 161 m (530 ft) average depth, and the completion of a tenth shaft (the previously built construction shaft). The Manhattan Tunnel contract was awarded to the sole bidder Schiavone/Shea/Frontier Kemper Joint Venture (SSF) for $668,532,680.00, on January 31, 2005. The Manhattan Tunnel was designed ?in house? by the New York City Department of Environmental Protection (DEP) and the construction management was provided by a combined staff of the DEP and a joint venture of Jenny Engineering and URS.

Jan 1, 2008

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By J. Luxford

The last decade has seen an enormous increase in the use of contractors right across the Australian mining industry. So much so that contractors now operate 33 of the 68 underground metalliferous mines around Australia and are making significant inroads into iron ore in the west and coal in the east. Safety used to be a low priority for many contractors. The picture has changed dramatically in recent years as most contractors take a far more professional approach to safety management. This paper examines the changes that have occurred and the requirements for effectively managing safety in a contracting environment.

Jan 1, 2000

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By T. Klemetti

Moisture deterioration of clay-rich roof rocks causes high numbers of roof falls in coal mines in humid summer months. Rocks with high moisture content are generally weaker and can further deteriorate when subjected to wetting and drying cycles. As a result, it is important to evaluate the moisture-sensitivity of roof rock prior to mining. The National Institute for Occupational Safety and Health (NIOSH) has evaluated three moisture-sensitivity index tests on roof rocks from 23 U.S. coal mines. The three tests were the University of Kentucky Weatherability test (Weatherability test), the Consol Energy Water Sensitivity test (Water Sensitivity test), and the NIOSH Immersion test (Immersion test). Of these three tests, the Weatherability and Water Sensitivity tests are more reliable in classifying the moisture-sensitivity of roof rocks. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

Introduction The science of geometallurgy requires that ore characterization be performed holistically, that is, with consideration of ore quality on plant performance and product quality. Geometallurgy, by definition, requires knowledge of geology, mineralogy, extractive metallurgy and pyrometallurgy. Examples of the ore characterization challenges for the geometallurgist in the production of iron ore pellets from low-grade Proterozoic iron formation are presented here. Ore Characterization Ore characterization, the quantifying of mineralogy, grain size and the texture of ores, is an often overlooked tool in improving process efficiency. Some mineral related problems are not unique to the production of iron ore pellets; e.g. the problems caused by expanding clays in flotation. The negative impact of carbonate minerals in the ore on pellet productivity and pellet quality are unique. The long and complex geologic history of Precambrian iron formations contribute to modifications of grain size and the introduction of complex textures.

Jan 1, 2007

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

There is wide agreement that sustainability has multiple dimensions, but substantially less agreement on the appropriate balance among those dimensions. This occurs because peoples’ vision of a sustainable future, their goals for sustainable development, and their objectives for resource management are reflections of their values, culture, and life experiences. Even assuming agreement about the objectives of sustainable resource management can be reached; there is still a need for policy and decision makers to choose from among alternative courses of action, each of which has its own set of impacts and outcomes. One of several tools used to compare the consequences of alternative actions is the Computable General Equilibrium (CGE) model. This paper uses CGE modeling to demonstrate how policy decisions do not take place in a vacuum and how policy-makers must be aware that there are trade-offs involved in any decision.

Jan 1, 2005

By D. Rendini, R. D. Gutridge

INTRODUCTION Gwinnett County, Georgia, is a part of the rapidly expanding metropolitan Atlanta Georgia area. Located approximately 48 km (30 miles) northeast of Atlanta, Gwinnett County has a current population in excess of 600,000 and is projected to reach a population of 1,200,000 by 2025. As a part of the County’s master plan to supply drinking water for the expanding population and to increase system reliability, the Gwinnett County Public Utilities Department undertook the Shoal Creek Raw Water Intake and Pump Station Project. Figure 1 shows a vicinity map for the project. Prior to construction of the Shoal Creek Raw Water Intake and Pump Station Project the County had a single raw water intake to feed water from Lake Sidney Lanier (Lake Lanier) into a filter plant for processing into potable water. This project together with a newly constructed water filter plant provides Gwinnett County additional capacity and system redundancy to prevent interruptions to the drinking water supply. Lake Lanier is a man made reservoir with over 800 km (500 miles) of shoreline and was constructed by the Army Corps of Engineers in the 1950s for hydro electric power generation, flood control, and navigation benefits for the Chattahoochee River. Over time, Lake Lanier has become an increasingly important source of drinking water for the metropolitan Atlanta area. This paper focuses on the primary underground construction and lake tap components of the project including a 42.7 m (140 ft) deep pump station shaft 24.4 m(80 ft) in finished diameter transitioning to a 6.1 m (20 ft) finished diameter shaft, a3.05 m (10 ft) finished diameter by 19.8 m (65 ft) deep intake shaft constructed in an average of 21.3 m (70 ft) of water, and a 190.5 m (625 ft) by 3.05 m (10 ft) finished diameter modified horseshoe tunnel connecting the two shafts. This raw water intake system, in conjunction with the incorporated pump station with 8 pumps and dual1,829 mm (72 inch) pipelines, provides a system capacity of 1,091,062 m3/day(240 MGD) to two water filter plants and is expandable by the addition of pumps to1,500,210 m3/day (330 MGD). Parsons provided design and construction management services for the project. The $29.6 million contract to construct the project was awarded to W.L. Hailey &Company. Notice to proceed was given August 6, 2001 and substantial completion was achieved on January 20, 2004. Value engineering changes adopted for the project contributed to completing the project at a final cost of $28.8 million.

Jan 1, 2005

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013