Search Documents

By S. Mathur, Pradip

Polyacrylic acid (PAA) was evaluated as a selective flocculant for the dolomite-apatite system. PAA with a molecular weight (MW) of 4 million was found to flocculate both dolomite and apatite. However, the flocculation behaviors of dolomite and apatite were significantly different with 450,000 MW PAA, which was found to be the lowest molecular weight fraction capable of flocculation. In single-mineral tests with a dosage of 2 kg/t PAA, 90% of the dolomite and 35% of the apatite flocculated. Selectivity was achieved in mixed mineral tests. From a feed consisting of an 80:20 mixture of apatite and dolomite, respectively, a concentrate containing 90% apatite was obtained with a 70% recovery. The dolomite rejection was about 75%, which corresponds to a 2% MgO content in the concentrate.

Jan 1, 1997

By Shelley M. Burg, Dennis K. Poulton, Robert B. Gordon

This project includes the excavation and concrete lining of approximately 18 900 m (62 000 ft) of 5.5 m (18 ft) finished diameter subway tunnel for the Los Angeles MTA. The project required that four soft ground headings be excavated from a single shaft located near the mid point of the tunnels. The tunnels were classified "gassy" during the excavation phase. Because of the contract schedule requirements and the limited urban work site available, many logistical problems had to be overcome during the project while excavation was accomplished at a record setting pace. Some unique project features include the muck handling system and an access shaft using a high strength tieback support system. In order to accomplish the work, an extensive effort to plan and construct the main work site was required.

Jan 1, 1995

By Joseph Cervik

Methane drainage methods can be broadly classified as surface or underground. Surface methods make use of vertical and slant holes. The underground method discussed in the present paper involves horizontal drilling from shaft bottoms and from locations along the periphery of mines. Every foot of hole drilled in coal from under- ground locations is productive and gas flows increase as hole length increases. Therefore, underground techniques have a great potential for producing large-volume flows of methane. Pumps to dewater the horizontal holes are not necessary because gas pressure forces the water out of the hole. Methane can be recovered through the use of a simple and inexpensive gas-water separator. Hydraulic fracturing, which has been used successfully to stimulate gas flows from vertical holes, has not proved practical in the case of horizontal holes.

Jan 1, 1980

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989

By R. Costa, A. Kozak, B. Fukuhara

Introduction The Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc. The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain. The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mined has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. and now Yamana Gold Inc.

Jan 1, 2007

By Jerome P. Downey

Treatment of tungsten ore at Anschutz Mining Company's Chicote Grande (Bolivia) operation results in a relatively high grade arsenopyrite byproduct stream. Laboratory and miniplant testwork have been performed at Colorado School of Mines Research Institute to examine the technical feasibility of recovering a marketable arsenic product fr an this source. Process selection was constrained by the remote location of the millsite, which demands an uncomplicated, low maintenance operation. As a result of the research effort, a two-stage roasting/condensing process was developed, featuring the use of an indirect heating method. Arsenic was efficiently extracted and the arsenic trioxide (As203) product consistently exceeded the industrial purity specification of 99.5%. Key process parameters have been secured for extrapolation of the process to pilot or small commercial scale.

Jan 1, 1985

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By Noel N. Moebs, John L. Ellenberger

Geologic structures in mine roof rock contribute to many roof falls in Appalachian coal mines. These structures include paleochannels, scours, pinch-outs, slickensides, clay veins, and cravasse splays consisting of thinly interlaminated sandstone and shale. These structures often can be identified during, and sometimes before, development and mine projections can be revised to reduce the adverse effects of discontinuities in roof structure. Large areas of roof consisting of laminated sandstones or incompetent strata generally can be delineated from exploratory drill-hole data and the need for supplementary support can be anticipated. Because an accurate description of roof geology also provides some indication of optimum length and type of roof bolts that should be installed, this Bureau of Mines paper describes the hazardous roof structures most commonly encountered in the Appalachian coal region.

Jan 1, 1982

By R. Simon

Strain-burst phenomena are generally characterised by sudden releases of energy in a volume of highly stressed rock. Strain bursts are encountered in situations such as crown pillar bursts during cut-and-fill mining, face bursts at development headings cord floor bursts in deep shaft sinking. This paper describes a simple two-dimensional linear elastic FE modeling approach that leads to the calculation of the energy-release rate (ERR) and the total energy storage rate (TESR) in the rock-mass around the openings. The merits of using such energy parameters in the analysis of strain-burst problems for identifying areas of high energy release/storage are discussed through a case stud v. However, much site-specific back analyses are needed to better understand how strain bursts and energy parameters are interrelated.

Jan 1, 1999

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

By Adolf J. Jonaitis

Outokumpu developed TankCell flotation cell technology beginning in 1990, following 35 years of successful flotation cell experience and application. In 1994, Outokumpu proved favorable operating success of 100-m3 (3,500-ft3) TankCells for porphyry copper and zinc flotation. In 1995, evaluation of a 150-m3 TankCell led to the successful application of these large cells in several operations. More than 350 TankCells of 100 m3 and larger in volume have been installed and are in operation. Key features of the Outokumpu TankCell design will be described. In addition, discussion of operating data from various metallic mineral flotation operations worldwide will be presented. Large flotation cell development continues today, with operating cell volumes of up to 160 m3 (5,500 ft3) in operation.

Jan 1, 1999

By Berthold Pilz

The importance of a power economy that is efficient both in technological and economic terms has been clearly recognized in recent years. In 1977 the German Federal Government therefore introduced its Energy Research and Energy Technologies Program 1977-1980, which consolidates the government activities in the field of nuclear and non-nuclear energy research. The priority objectives of this program can be summarized as follows: safeguarding the medium- to long-term energy supply in the Federal Republic of Germany at reasonable overall macroeconomic cost, taking into account the requirements of environmental protection and the safety of the population. In the field of coal mining technologies, about 200 research projects are currently under way. A total of DM 1.7 billion is earmarked for research to be conducted in this area between 1977 and 1980.

Jan 1, 1979

By Roland Hoet, Jim Patilla, Nick Madison

Increasing conveyor capacity and reliability is a common goal for many underground mines. This task is especially challenging when you must work with existing structure, belt, etc. Meeting this challenge, The Pittsburgh & Midway Coal Mining Co. North River Mine switched from constant fill to actively controlled fluid couplings, realizing a capacity increase from 2,100 tons per hour (2,300 stph) to 2,550 tons per hour (2,800 stph), with improved reliability. This paper will present a case study of The Pittsburgh & Midway Coal Mining Co.'s North River Mine underground conveyor haulage system. These conveyors included the main line conveyors as well as a tension controlled tripper booster panel conveyor. Characteristics and performance of the coupling and control system will be illustrated, demonstrating the systems controllability, simplicity, and dependability.

Jan 1, 2002

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By M. R. Fletcher

Slags generated by the ferrous metals industry can he used to produce high-value ceramic materials. The properties of these ceramics can be controlled by judicious choices of composition, additives, and processing parameters. Standard methods of materials handling, such as comminution and mixing, are as applicable to slag as to any other mineralogic raw material. In this study, foundry slag was ground, homogenized, melted, and, formed to produce a glass, and then heat treated to crystallize it into a high-strength glass-ceramic. The product shows promise as a low-cost, wear-resistant tile material that (-an he custom cast. This and similar materials made from slags and natural rocks are candidates for use as construction materials, acid-resistant piping, shock-resistant sheathing, rot-proof pilings, and, when foamed, even as pontoons.

Jan 1, 1990

By Graeme Lyall, Oy Leuangthong, Clayton V. Deutsch

There are many variables to consider in the evaluation of nickel laterite deposits including the concentrations of nickel, iron, silica, and magnesia. These variables show complex relationships with each other such as mineralogical constraints, non-linear correlation, and heteroscedasticity. The complex multivariate relationship between the variables cannot be reproduced by conventional Gaussian or indicator geostatistical techniques. We introduce the stepwise conditional transformation method as a pre- and post-processing multivariate transform for the stochastic simulation of a nickel laterite deposit. Transformed data are multiGaussian and independent at h = 0; thus, cosimulation can be avoided after verification that variables are independent at all lag distances. Back transformation restores the features of the input multivariate distribution to the simulated realizations. The complex multivariate correlations are reproduced and sensitivity issues are addressed.

Jan 1, 2002

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By R. A. Metz, Michael M. Easdon, Michael J. Fiannaca

Disseminated epithermal gold metallization occurs within a breccia unit interpreted to be a submarine debris flow. Gold is associated with oxidized pyrite, fluorite, and jasperoidal silica. A minimum of 8 Mt (9 million at) of open-pittable mining reserves will be cyanide heap leached as run-of-mine ore at a rate of 0.9 Mt (1.0 million stpy). Careful evaluation of the combined results of successive sampling projects has established the pit plan, minable reserves, and process metallurgy of the operation. The sampling procedure utilized for a given test depended upon geological interpretation as well as the procedures, successes, and failures of previous tests. This paper summarizes the sampling and testing procedures of the development effort in light of the project goals and attendant problems in achieving them.

Jan 1, 1992

By E. J. Peuraniemi, J. T. Yli-Penttilä, A. Jokilaakso, K. M. Riihilahti

Dust formation and the reaction mechanisms of copper matte particles were investigated in simulated flash-oxidation conditions. The granulated and ground matte consisted of 72% Cu, 4% Fe and 21 % S (by weight). Experiments were conducted by using a laminar flow furnace with a reaction-gas composition ranging from 20% to 75% O2 (by volume) in nitrogen. The particle feeding was carried out by a single-particle method, and samples were quenched after a specified reaction time ([~] 0.05 to 0.4 s) in a cold water film. Experimental temperatures ranged from 800o to 1,300o C. Chemical analysis was used to determine the degree of oxidation, and optical and scanning electron microscopes, combined with energy dispersive analysis, were used for characterization of the reacted particles.

Jan 1, 1999