Search Documents

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By G. G. O. O. Uwadiale, M. A. U. Nwoke

The recovery of iron from low-grade (31.6% Fe) Muro iron ore was investigated using reverse anionic flotation of quartz. Tests were performed to investigate the effect of pH, the effects of using distilled vs. tap water as the flotation medium and the effects of using cassava starch vs. dextrin for the depression of iron minerals. The optimum results were obtained around pH 10 and 11, and cassava starch was superior to dextrin in depressing iron oxides. Investigations at pH 11 using cassava starch and distilled water resulted in a concentrate grade of 69.4% Fe with a recovery of 84.4% Fe. Under the same conditions, the use o f dextrin produced a concentrate grade q f 65.9% Fe with a recovery of 78.6% Fe. Investigations at pH 10 using cassava starch and distilled water resulted in a concentrate grade of 60.2% Fe with a recovery of 83.9% Fe, and under these conditions the use of dextrin produced a concentrate grade of 56.1 % Fe with a recovery of 81.5% Fe. Flotation studies conducted at pH 11 using tap water and cassava starch resulted in a concentrate grade of 70.4% Fe with a recovery of 92.7% Fe. This demonstrated the superiority of tap water over distilled water in the reverse anionic flotation process. Investigating the effect of calcium ions on the activation and flotation of quartz with oleic acid revealed that a calcium ion concentration of 50 to 100 ppm was optimum.

Jan 1, 1996

By Donald G. Wieland, James H. Meinholz

INTRODUCTION The Milwaukee, Wisconsin Metropolitan Area provides an ideal opportunity to review the advancement of the art and science of mixed face tunneling in the past 65 years. Although there were earlier tunnel projects in the Milwaukee area, by other agencies, the majority of those driven in the Twentieth Century have been done under contract with the Milwaukee Metropolitan Sewerage District through the agency of the Sewerage Commission of the City of Milwaukee and the Metropolitan Sewerage Commission of the County of Milwaukee. Legal Description of District The Milwaukee Metropolitan Sewerage District was created by the Wisconsin Legislature in 1921 together with the Metropolitan Sewerage Commission of the County of Milwaukee. This concept of subregional wastewater control was an outgrowth of an investigation and report from a commission appointed by the Common Council of the City of Milwaukee in 1909 to study final sewage disposal for the City. In 1911 that Commission, comprised of J. W. Alvord, George C. Whipple and Harrison P. Eddy, recommended that the City construct a water filtration plant, construct a Menomonee River flushing works, expand the intercepting sewer system and, after a thorough study of the then existing and developing methods of sewage treatment, construct a sewage treatment plant. In response to those recommendations, the Wisconsin Legislature, in Chapter 608 of the Laws of 1913, created the Sewerage Commission of the City of Milwaukee. Recognizing that the improvement of surface water quality would require action on a watershed basis, the Legislature, in Chapters 554 and 590. of the Laws of 1921, created the

Jan 1, 1979

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By R. Asamoah, K. B. Owusu, G. Abaka-Wood, W. Skinner

The hostile nature of industrial autogenous (AG)/semi-autogenous (SAG) mill operation necessitates the need for robust and reliable online measurements. Mill slurry density is regarded as a critical variable and requires a suitable range for grinding efficiency. In this work, mill acoustic sensing of five different slurry densities (50, 60, 70, 80 and 90 wt.% solids) was investigated using a laboratory-based AG/SAG mill. The results showed that slurry density of 70-80 wt.% solids gave the highest mass of -75μm particles and similar acoustic intensity. The mill acoustical level increased continuously coupled with energy reduction as a function of increasing slurry density, an indication of potential realtime measurement.

Mar 2, 2022

By Byron M. Jones

The use of computers in system analysis is well established. Analog computers have been used for this purpose since about 1940. As the power of digital computers increased and their cost decreased, much of the analysis formerly done by analog computers has been diverted to digital computers. The mathematical foundation for system analysis was laid between the years 1700 and 1900. In the 1930?s, telephone repeater amplifiers were designed using systems analysis techniques. From 1940 to 1960 systems were analyzed using either direct simulation or LaPlace transforms. Since 1960 analytical methods have been expanded to include linear vector space theory. All of these methods are being used to analyze the dynamic behavior of mining machinery.

Jan 1, 1974

By K. Komnitsas

This paper presents the main environmental assessment techniques and indicators that can be used a) for the establishment of a sustainable development framework and b) for the evaluation of the environmental performance within the mining sector. Reference is made to techniques as environmental risk and impact assessment, life cycle assessment, cost benefit analysis and best practical environmental option assessment that can be used as tools to assess environmental impacts of processes, activities and products in the mining sector. In addition, the issue of environmental indicators, covering operational, management and environmental areas, that provide valuable information regarding both the environmental performance of a mining company and its efforts to influence this performance towards sustainability is discussed.

Jan 1, 2003

By R. Gehauf

Magnetic separation using rare earth rolls (RER) and rare earth drums (RED) have seem tremendous development and use in recent years. While the process of magnetic separation is understood, the principles affecting the separation, the specific application and the optimization of RERs and REDs are less well known. This paper offers practical insight into the basic operation, selection and optimization of RERs and REDs. It is a guide for the engineer who must design a test series and select the proper equipment for that application. It provides the engineers and line operators who control the daily operation of the equipment a basic understanding of the dynamics of operation and the principles that govern the optimization of RERs and REDs.

Jan 1, 2004

By Po-Wei Tun, Kuen-Yuh Wu, Tso-Min Shih, Hsi-Chiang Fang

The purpose of this study is to investgate the coal dust explosion characteristics and to search for the prevention methods of the coal dust explosion as well as the propagation of the explosion flame of the middle-bearing coal formation in Taiwan by an open type coal dust explosion apparatus in laboratory. The coal samples were taken from the typical middle-bearing formations of the Sam-Ming,Tai-Ho and Lee-Fong coal mines The rock dusts, the free water mixture with coal dust samples and the interval clean out the coal dust in the testing chambers were applied for preventing the coal dust explosion and the propagation of the explosion flame.

Jan 1, 1993

By Nico Bezuidenhout, André M. van Niekerk, Jan J. G. Vermaak

This paper documents empirical evaluations of geochemical data that was recorded during a seven year pilot scale experiment. The experiment was aimed at assessing the effectiveness of natural soil covers for rehabilitation of coal discard facilities. Ten test cells were constructed using different natural soil cover materials and configurations. Results of the evaluation indicate that, although a pH breakthrough was not recorded for the single layer soil cover cells as was the case with the uncovered cells, single soil covers were not effective in preventing ARD oxidation processes. Multi layered soil covers were found to be able to create anaerobic conditions leading to a reduction in ARD oxidation processes and an improvement in leachate quality.

Jan 1, 2000

By A. Bruce Waugh, W. W. Wen, Kevin N. Clark, Neville C. Lockhart, Bruce A. Firth

Australia is the world's largest coal exporter, and technological advancement is a key element of the coal industry strategy. The issues include: increased recovery of saleable coal; enhanced quality, i.e. lower ash, moisture, fines, phosphorus (sulphur is a relatively minor problem for Australian coals); better quality control; higher throughputs/lower costs; improved handling and transport; and reduced environmental impacts. In process terms, many coal preparation operations, particularly fine coal circuits, are relatively inefficient, and all circuits must also be matched and integrated for optimum overall operation. A holistic approach to technological improvement is desirable. This paper summarises research and development efforts, within CSIRO and its collaborators, across the unit operations as outlined in the title.

Jan 1, 1995

By Barry J. Hansen

Mining can make two major contributions to the cleanup of the environment. The first of these is the extractive technology that has become highly developed as a result of centuries of development. Of equal impor­tance are the methodology of analysis and the development of engineering solutions that are the stock in trade of the mining industry. Despite the differences between the industries, the processes for the development of a mine and the cleanup of a hazardous waste site are similar. The characteristics that impact the ability to develop a suitable process for treating an ore body or correct­ing an environmental problem are those relat­ed to the distribution of the contaminant or metal in the host material.

Jan 1, 1991

By Thomas M. Goodell, Timothy D. Arnold

Dilute-phase pneumatic conveying has been used in the mining industry since the 1920s. It has primarily been used for the hoisting of coal and salt ores, and as a transportation medium for backfill material. More recently there have been investigations into a wider variety of applications, which this paper addreses. The paper will point out some deficiencies in the system. It 1s not the "champion" of the mining industry, but rather an excellent srste?1 with a variety of applications that may not have been studied m enough detail. The most imaginative applications to the Redpath Pneumatic Conveying System have been initiated by persons needing an innovative application to a specific predicament.

Jan 1, 1992

By Bob Snashall

Mines, miners and mining figured in the revolutionary birth of the USA. This occurred with a little help from General Washington's friends, the French. When the colonial minutemen confronted King George's "bloody lobsterbacks" at Concord, MA, in April 1775, the resulting "shot heard around the world" resounded in Versailles. France was sympathetic to the patriot's struggle. Before the Lafayettes shipped out, came French muskets and powder... but not many musket balls. The Continental Congress issued orders to get the colonial lead out for shot and shell. Colonial mining enterprises had been chiefly local affairs, cheaply supplying product to the surrounding communities. Since wood was accessible for fuel, coal had not been exploited.

Jan 1, 1990

By T. S. Golosinski

Timely and efficient conversion from traditional to sustainable development of mineral resources requires that managers, engineers and other mineral industry professionals become familiar with the related techniques and methods. To fill this need the online Master of Engineering program has been developed at University of Missouri-Rolla. Designed primarily for mature students with an engineering or science background this program allows for specialization in several areas of sustainable development of earth resources. To accommodate mineral industry professionals working in remote locations all courses constituting the program can be taken online, without the need to attend the classes in person. The paper describes the program and discusses the experience gained during the first two years of program offering.

Jan 1, 2003

By J. L. Post

A near-surface body of readily available Na-montmorillonite is located about 24 km (15 miles) southeast of Fallon, NV. The clay, which forms an irregular deposit about 4.8 km (3 miles) long, lies in altered rhyolite within a fault zone. The clay is similar to Wyoming bentonite but is less uniform in composition and contains less MgO and more Fe2O3 in its crystal structure. The clay interlayer cation population can be estimated by using a modified DTA procedure. With selective mining, the industrial properties of the Nevada clay are adequate for use as drilling mud, in foundry applications and as a sealant for hazardous wastes and canals.

Jan 1, 1997

By Dale J. Sadowski, Richard J. Switalski, Kyle R. Ott

This paper discusses design and construction aspects of shaft construction through rock saturated with petroleum hydrocarbons (crude oil). During the subsurface exploration phase for design of the Hilltop Interceptor project in Cleveland, Ohio natural crude oil was encountered at depths between 6.1 and 61 m below ground surface. The oil-saturated Euclid sandstone contained up to 12,000 mg/kg total petroleum hydrocarbons (TPH), various volatile organics, and had flash points as low as 18.9°C. Interceptor hydraulic design required that construction of access and/or drop shafts penetrate the layer of petroleum hydrocarbon saturated rock. This led to the design of a special lining and some special handling procedures for the excavated material.

Jan 1, 1995

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By Henry R. Tiedemann, William H. Hansmire, Harvey W. Parker

Although the use of precast concrete segments for tunnel linings has been common for many years in Europe, acceptance of this type of lining has been slow in the United States. This paper explores the cost, design, and construction considerations of concrete segmental lining with a view to promoting its use in this country when favorable conditions exist. The different perspectives held by owners, designers, and contractors are discussed. In addition to cost, other considerations include previous design and construction experience, size, length and function of tunnel, watertightness, and liability. Cost comparisons are made to traditional ground support and lining. Under favorable conditions, the use of precast concrete segmental linings can be technically feasible and cost effective.

Jan 1, 1987