Search Documents

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

By Ernest K. Yanful, Paul H. Simms

The lysimeter is a useful tool for evaluating the performance of mine waste covers or liners. A major problem with its application is the possibility for preferential flow into or away from the lysimeter, if the lysimeter soil is finer or coarser than the barrier soil or sub-base soil. Analysis of a field lysimeter using a two-dimensional unsaturated-saturated liquid flow model suggested that preferential flow would occur and little or no water would be collected; however, in the field, the lysimeters collected significant amounts of water. A similar discrepancy was found between the observed and predicted water balance of a simple laboratory test simulating the lysimeter design. Vapour flow and partial flow, two phenomena not generally simulated in conventional flow models, are possible explanations for the difference between field and laboratory observations.

Jan 1, 2000

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By John L. Watson, Suren Mishra

Many of the wastes produced by modern steel plants are pulps or sludges containing significant concentrations of iron and displaying some ferromagnetic characteristics. These waste materials are often suited to treatment by magnetic cycloning to produce a high solids content underflow and a clean water overflow. Alternatively in the classification mode, the magnetic cyclone can produce a high iron underflow product for recycling by discarding fine non-magnetic material to the overflow. Results for the treatment of a variety of steel plant wastes in 5.0cm, 2.5cm and 1.25cm diameter cyclones, operating with and without an applied magnetic field, are presented. It is demonstrated that the magnetic cyclone increases solids recovery to the underflow product, especially at finer particle sizes and for higher solids content feed pulps.

Jan 1, 1992

By Denise Herzog, Sukumar Bandopadhyay

This paper presents an application of analytical hierarchy pro- cess (AHP) to predict the ranking of three beneficiation methods for a low grade, bulk gold deposit located in the interior Alaska. Seven criteria (attributes) were used for evaluating each beneficiation method. For each criterion a matrix of pairwise comparison between methods was developed. The normalized eigenvector of each matrix scales the beneficiation methods with regards to that criterion. An overall scale is constructed by weighting the scales of all the criteria. Methodology used also indicates a measure of inconsistency. This measure is useful in identifying possible errors in expressing judgments as well as actual inconsistencies in the judgment themselves. The outcome of the pro- cess is the best or optimum beneficiation method, considering all the necessary objectives, criteria, and alternatives in a single integrated framework.

Jan 1, 1996

By John A. Bischoff, Francis S. Kendorski

A technique that has been used for inspection and appraisal of rock tunnels is described. It enables a rapid and complete record to be made of those factors necessary for the engineering assessment of the rock conditions surrounding a tunnel. Full understanding of the regional geology, and a careful recording of data concerning the principal geological and construction factors is essential basic data for a tunneling project, whether the tunnel is under construction or is already in service. A methodical recording of data concerning general geology, shears, fracture orientations, spacing, persistence, rock classification, water condition, shear frequency, excavation method, blasting procedure, and rock stabilization and support methods, combined with a photographic record, can be completed by experienced engineers and geologists at the rate of over 1000 feet of tunnel per shift.

Jan 1, 1976

By C. Anderson, K. Nikkhah

This paper outlines the role of simulation software in design and operation of a typical metallurgical plant with mineral processing and hydrometallurgical units, to produce concentrate and pure metal. It addresses the role of simulation and mass balance software in the conceptual, feasibility and detailed design stages. It discusses the use of JKSimMet for sizing of mineral processing units, and METSIM and IDEAS for development of energy and mass balances. In detailed design of a plant, the complex interaction and variation in performance of various units makes it difficult to predict overall system performance and availability. Simulation is used to: assess operating strategies that affect surge capacities at various stages compare different ore types and mining strategies that affect concentrate product quality. optimize transportation logistics for raw materials, concentrate and metal products

Jan 1, 2001

By Drupad B. Desai

Baltimore Region Rapid Transit System project final design began in 1973. The Section A of the planned Phase I is scheduled to go into revenue service in late 1982. The subway line structures include earth tunnels, rock tunnels and cut-and-cover structures. Final designs were performed by both the DMJM/KE staff and by outside subconsultants. This paper deals with Section A of the program. (Fig. 1.) The overall program cost for Section A is estimated to be $721 million. The cost for construction and owner furnished equipment is estimated to be $600 million, including contingency and escalation to time of construction. The remaining amounts are for right-of-way, design, construction management and agency (MTA) costs. The Section A line structures, including station lengths, are divided as shown in Table 1. [ ]

Jan 1, 1979

By H. Polat, M. Polat, S. Chander

A high shear treatment step was observed to improve flotation of coal. The effect of high shear treatment (HST) was a strong function of coal rank, however. For the low rank coals the HST produced loose, open-structured agglomerates which decreased the entrapment of ash minerals. For the high rank coals, the high shear treatment promoted detachment of low-floating particles from the agglomerates that ordinarily formed in a flotation cell. The extent of agglomeration and detachment of particles from the agglomerates was a function of the amount of dodecane and coal rank. To obtain desired efficiency of separation ethylene-propylene oxide block co-polymers were used. The results showed that the HST-flotation technique increased the ash rejection considerably for both high and low rank coals, though the mechanisms were different.

Jan 1, 1995

By M. Prasad, A. K. Majumder, T. C. Rao

The depletion of high-grade phosphate ores is bringing about a search for a suitable, economically viable technique that con process the abundant low-grade phosphate reserves. About 75% to 80% of the world's low-grade phosphate reserves are associated with carbonate gangue that is not amenable to treatment by the simple techniques of physical separation. The processing of sedimentary dolomitic/calcareousphosphate ore has numerous problems, including similar surface properties of the carbonate and phosphate. Two-stage reverse anionic flotation of carbonates (dolomite/calcite) has appeared to be a promising separation technique ,for the removal of carbonates from sedimentary rock phosphate. In reverse fatty-acid anionic flotation, the depression of phosphate mineral with orthophosphoric acid produces satisfactory results for calcareous as well as dolomitic phosphate ores from several locations of sedimentary origin.

Jan 1, 2000

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have been made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modeling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developed that can be calibrated for ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables prediction of the complete composite particle distribution and thus is valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1988

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By William R. Nash

Introduction As ore grades decline and deposit depths increase, problems and costs of mining construction increase rapidly. Ground water greatly impacts the cost of mining construction. In developing or exploiting ore bodies or coal mines, stored ground water in waterbearing formations is often encountered. Man-made conduits or shafts are constructed, as are raise bores for ventilation (up to 6-m-diam or 20-ft-diam), or smaller diameter drill holes, used for either power cables or rock dust. In underground construction and mining, it is possible to inherit unmapped and abandoned drill holes either from oil or gas exploration, or from previous geological investigations. There also exists within underground work exposure to faults, fissures, and jointing. A mine development may encounter unknown aquifers or, unluckily, have an ore body that is an aquifer. Water may invade an existing underground structure, due to concrete deterioration or to damage that may occur to an existing shaft or tunnel concrete lining. An underground development may intersect a drill hole that was not properly grouted when abandoned. It subsequently formed a conduit or an active path to conduct water into the mine. Water inflow may range from insignificant to a magnitude sufficient to inundate an area or an entire underground development. Corrosion imposes major costs. In shafts, it can cause accelerated wear and deterioration, and subsequent early replacement of hoisting ropes. It can also cause deterioration, misalignment, and subsequent accelerated wear and replacement of timber and steel guides and buntons. Utility maintenance (power cables, air, water, and ventilation lines) also can become a problem. Corrosion imposes major costs. Skips and skiploaders provide a never-ending series of maintenance headaches when exposed to an ingress of water. Numerous problems are found in declines with invert and rail maintenance and with partitions in over-under coal mine slopes. Ground water interacting with an underground ventilation system can result in: • Increased ventilation resistance due to roof falls and the spalling of ribs caused by ice heaving. • Restriction in shaft or slope cross-sectional area due to ice buildup during winter months. This may be a safety hazard to access as well. • An increase in the moisture content entering the ventilation air that condenses underground and causes electrical and equipment maintenance problems. Underground structures also incur water-caused problems. The concrete lining in shafts, slopes, and tunnels may be subject to: • Active mine waters causing concrete and reinforcing steel to deteriorate - perhaps to the point of collapse. • Load redistribution around a concrete lining, caused by soil dislocation due to water movement. The resulting stress may be in excess of the calculated design loading. Backwall injection with grout of the completed concrete lining may solve these water inflow problems through low-pressure injections of cement and chemicals. This fills voids at the interface of the concrete lining with either the soil or rock excavation. Surface structures may be jeopardized by lowering the ground water table, resulting in surface settlements. Surface settlements can occur in buildings, headframes, hoist foundations, mills, conveyor structures, or in rail haulage. Areas of differential settlement can lead to derailments, improper wear of hoisting ropes on sheaves in headframes, and the misalignment of bearings and brakes. Mud jacking and compaction grouting may remedy these problems. To reduce operating costs, increase efficiency, and increase safety, inflow water to the mine should be minimized. For an operating mine with a water problem, a water inflow survey should be taken. Quantities of water flow should be examined at all accesses (shafts, slopes, bore holes, and raise bores) at the faces, haulages (rails or conveyors), and sump discharge. From this examination and quantity survey before and after heavy rainfalls, valuable data for elim-

Jan 3, 1984

By Katherine Hynard, Colin Eustace

Development quarterly mine plans is generally time-consuming and requires consideration for many operational constraints and competing objectives. With lengthy turnaround times, there is often limited opportunity to adjust the quarterly plan details to account for differences between actual state of the mine operation at the time of execution and expected state at the time that the plan was developed. Actual mining task completion times can vary significantly from the expected task completion times, due to many factors. In the absence of revision to account for differences between the planned and actual state, resource allocations and mining sequences, embodied in the quarterly mine plan may no longer be the best approach at the time of execution to achieve an efficient mining operation. Simulation and optimisation tools can be used to support rapid refinements for development and execution of weekly mine plans. When initialized with an operations data feed to establish the actual state of the mine operation, optimisation models can be used to facilitate both automation and revision of the quarterly plan to produce a weekly or daily plan for execution. This approach can remove much of the manual burden of revision if the existing quarterly plan no longer represents the best approach to meeting production objectives. Following initialisation with mining actuals, simulation models can provide a representation of the range of likely mine operations outcomes. The models can be used to accelerate the planning process by providing visibility of future performance and identifying likely operational issues. They can also be used to test the robustness of the plan with respect to performance variability and response to disturbances. Following identification of issues, simulation models can also be used for evaluating mitigation measures, through automated testing of alternative plans. Integration of mine data feeds with simulation and optimisation tools enables automated optimal responses to variations between the quarterly mine plan and actuals to be tested prior to release of and execution plan and implementation. The use of simulation and optimisation in weekly mine planning will be discussed in this paper with reference to surface mining examples.

Jun 25, 2023

By F. Gray

Diamond tool fabricators expect strong growth in most applications for 1995 and 1996. Overall growth projects range from 8% to 10%. Diamond grinding is forecast to grow between 5% and 8%, while cubic boron nitride grinding should grow between 10% and 12%. A strong automotive industry is a major factor in this projected growth, as is continuing demand for other durables

Jan 1, 1995

By Rudolf Greuer, Gerald Jalkanen, Huann-Sheng Chen

A short cut is presented where the average grade above a primary grade cutoff and its associated byproduct grade(s) are estimated by screening the primary and byproduct grades. For the primary variable, choose samples whose grades are above a cutoff of interest. Compute variograms for the subset of the primary variable. Then using this variogram, krige the blocks of interest only using the samples whose grades are above the cutoff. The next step is to screen byproduct grades by choosing byproduct samples whose associated primary grades are above the cutoff of interest. Next compute variograms for this subset of byproduct samples. Then using this variogram, krige the blocks of interest using byproduct sample grades whose associated primary sample grades are above the cutoff of interest. The results are the average grade above a primary cutoff for both the primary and the associated byproduct variables. Using two simulated primary and reference data sets a case study resulted in the screening krigings performing better than the indicator kriging approach in the first case study. A second case study had mixed results with the primary indicator approach performing better than the primary screened approach. The byproduct screened approach performed better than the byproduct indicator approach.

Jan 1, 2002

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons&apos; theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By C. H. Lee, F. Concha, L. G. Austin, P. T. Luckie

The Concha-Almendra batch-settling treatment for concentrated suspensions of single-diameter spheres has been modified. This modified version is used in the differential equations of simple batch settling of a particle size range of different density materials. The equations have been programmed for a finite difference solution, and a number of test cases have been analyzed. By cutting the settling column at a fixed fractional height, the material below this height can be treated as underflow and the material above as overflow. The predicted partition curves obtained from treating the settling in this way have Sharpness Indices in the range of 0.5 to 0.6, in the absence of dispersion effects. The Sharpness Indices decrease as dispersion increases. When the feed size distributions are of the Rosin-Rammler form, the partition curves (corrected for the bypass fraction) fit the Rosin-Rammler equation with reasonable accuracy. The predicted Sharpness Index of a component of a mixture of two materials of different densities was unchanged from that of the same materials settled alone. However, for the same, feed size distribution and volume fraction of solids in the feed, the heavier material settled faster, and the lighter settled slower, than when settled alone.

Jan 1, 1993