Search Documents

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016

By M. C. Fuerstenau

Collophane, cryptocrystalline fluorapatite, is examined as a substrate for plant water and wastewater remediation. The attenuation of Fe3+, Cr3+, Fe2+, Cd2+, Hg2+ and Pb2+ is presented as a function of metal ion concentration, amount of collophane, initial pH and conditioning time. TCLP results for Pb2+ contaminated collophane are presented. Mechanisms of adsorption for divalent and trivalent species are suggested. Key words: Collophane, Wastewater remediation, Heavy metal removal

Jan 1, 2003

By M. Tarshan, M. C. Williams, T. P. Meloy

A methodology is presented for the spreadsheet solution of separation processing networks. With the methodology developed, a spreadsheet grid is used to represent networks both with and without recycle loops. In this manner, network solutions are numerically approximated by spreadsheet grid solutions. The methodology was used to explore the ramifications of networks developed by the Chinese for tungsten and molybdenum processing Nonlinear stage-transfer functions for two-component sharp separations can be used.

Jan 1, 1996

By T. Ertekin, R. V. Ramani, W. Sung

The emission of methane in the coal mine working faces has two immediate impacts with regard to coal mine planning. Firstly, at the planning stage, the coal mine ventilation system must be designed such that airflows in the faces keep the concentrations of the gas in faces areas to below one percent. If the concentrations were greater than one percent, the production machine has to be shut down resulting in a loss of productive time. In an extreme case, concentration can reach explosibility limits which may lead to ignitions and explosions. Secondly, in excessively gassy coal seams, several alternatives can be applied to the mine layout configuration, and the mining method to be predicted for the extraction of coal, so as to insure a productive and safe operation. In this study a two-phase, two-dimensional finite-difference model was used to predict the methane emission rates into active mine working area under several methane drainage schemes. The numerical model utilizes a recently developed multi-mechanistic flow theory which describes the flow of methane in an heterogeneous and anisotropic coal seam. Transport of methane in the micropore structure of the coal is described by the Fick's law of dif- fusion under the influence of existing concentration gradient, while flow in the more permeable butt and face cleats (macropore spaces) is formulated by Dar- cy's law under the influence of existing pressure gradient. The desorption of the methane is accounted with the aid of a quasi-steady kinetic sorption model. A series of simulation studies were conducted in a systematic manner by sifting through the parameters associated with the coal seam characteristics and the degasification strategies in order to understand those which most significantly affect the methane emission rates in the face areas during mining. Along these lines, the effects of coal seam properties such as thickness, porosity, permeability, sorption characteristics and scheduling of drainage process against the mining operation have been isolated to understand the role of each individual parameter on the methane emission rates.

Jan 1, 1987

By J. H. Rowland

Four different types of fire suppression systems were evaluated in large-scale fire experiments to study the effect of air velocity on the effectiveness to extinguish conveyor belt fires. The four different types of suppression systems were water sprinkler, deluge type water spray, and two different dry chemical fire suppression systems. The large-scale fire tests were conducted with 72-in-wide fire resistant rubber belt that met the Mine Safety and Health Administration flame resistant requirement specified in Title 30, Code of Federal Regulations, Part 18, section 18.65 (also known as the 2G Flame Test). Each fire suppression system was tested at air velocities of 500-550 feet per minute (fpm) and 1350-1500 fpm. Two tests were conducted at both air velocities for each fire suppression system. Both of the water-based fire suppression systems were able to suppress the fire to the point that a miner could extinguish it with a fire extinguisher. However, the amount of water needed to suppress the fire to the point where a miner could walk up to extinguish any smoldering belting was greater than the current MSHA regulations require. MSHA regulations only require 10 minutes of water supply to the suppression system. In the test set up neither of these systems would have suppressed the fire had the water been turned off to the system after 10 minutes. The dry chemical suppression systems produced mixed results. Dry chemical suppression system A did not suppress the conveyor belt fire at either air velocity. Dry chemical system B suppressed the fire at 500 fpm air velocity, but produced mixed results at the higher air velocity. Details are presented on the large-scale fire test set-up, arrangement of the fire suppression systems, and conclusions regarding the effect of air velocity on fire suppression system design and performance. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Matthew Horsnell

Greenbank Terotech is a member of the Halley & Mellowes Group of Companies and is accredited t AS3902. Greenbank has been involved within the wear resistant lining industry for over 20 years. Initially supplying cast Basalt piping systems through to the present day breakthroughs with SiTech cyclone linings. The challenge of finding the most cost effective cyclone lining has been a difficult process. Over the years many varieties of ceramics have come and gone. In particular within cyclone applications, many people have become disillusioned with the term "Ceramic." In practice, it was discovered that if a ceramic worked in one part of the plant, it did not necessarily work in the cyclone area. A good example of this is Alumina chute and pipe linings. An Alumina lined cyclone underflow bend would provide exceptional wear resistance, whereas an Alumina Spigot would have failed miserably. After Alumina's were tried, Silicon Carbides were experi­mented with. The results in many trials were mixed. What worked at one mine did not work at another. The results did not conclude decisively that ceramics were here to stay within the hard rock cyclone area. It was then that Greenbank Terotech started to look at the reason "Why do some linings work and others don't." We came to the conclusion that the matrix holding the particles together had to be the key to a successful cyclone material. At the time we looked at materials such as Alumina Bonded Silicon Carbides, Metallic (Aluminium) Bonded Silicon Carbide, 99% Alumina Ceramics and Nitride Bonded Silicon Carbides, but all these materials either suffered from chemical attack on the Aluminium matrix (via cyanide) or the matrix simply was not hard enough causing wear rates to be excessive. It was then we looked at SiTech. SiTech is a unique material in that the primary particles are Silicon Carbide, but the matrix is made up of a Secondary Silicon Carbide formed within the reaction bonding process.

Jan 1, 1995

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By S. Chander

A mineral or metallurgical process uses various inputs, such as ores, energy and other raw materials, to make different products that fulfill societal needs. The processing of raw materials has changed in recent years due to the increased complexity of processing low-grade ores, intensifying competitiveness and greater constraints. For process improvement, various plant optimization and process modifications must be conducted under environmental, social, political and economic constraints. Processing research and education's success in meeting the process industry's future needs depends on an adequate balance between micro- and macro-engineering approaches. In its simplest form, macro-engineering is concerned with the "big picture," while micro-engineering requires looking at a subset of the process. So macro-engineering may be defined as an investigation of the larger or "whole" system to achieve the desired goals. And micro-engineering may be viewed as a quantitative investigation of a subset of the process, to determine cause-and-effect relationships within the subset. Two different approaches might be used in macro-engineering analysis. In one, the big picture may be viewed without a detailed knowledge of the subunits. With this approach, statistical tools are used to relate input and output parameters. Also, actual plant data or analog models might be used to obtain the desired information. The usefulness of such an approach increases with problem complexity. To attain the desired goals using the second, "model-based," approach, a detailed knowledge of the subunits is often useful and their interactions may be considered. In complex process analysis, the first of these approaches is more useful since less information is needed. However, it is also less exact and more likely to fail if there are significant changes in conditions and interactions. The second approach, on the other hand, is more exact, with greater predictive ability within the narrow subset being considered. Consequently, it is difficult and costly to conduct.

Jan 1, 1992

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By Gene E. McClelland

4.1 INTRODUCTION Metallurgical testing is required on any ore, waste or tailing material before amenability to heap leaching treatment can be accurately determined. The amount of testing necessary to determine and optimize heap leach amenability and conditions for any feed material is determined by the ore type, grade, size of deposit, and the overall financial commitment a particular company is willing to make. It is very easy to either "under-test" or "over-test" a particular deposit or feed material. A good heap leach testing program will provide the necessary design information without "bogging" down in too much detail. The three basic stages of ore testing include: • Preliminary--bottle roll tests and small column percolation leach tests; • Detailed--larger column tests, different feed sizes, and feed size optimization; and • Pilot-Scale--Column or field heap. The following subchapters describe the stages of heap leach testing necessary to put a viable property into production. 4.2 PRELIMINARY METALLURGICAL TESTING The two types of preliminary tests that can be undertaken include bottle roll or cyanide agitation tests and small column leach tests. Each of these is described below, along with information about what the test results provide in terms of furthering knowledge of ore qualities. 4.2.1 Bottle Roll Tests The first step in a heap leach testing program is preliminary bottle roll tests at a relatively coarse feed size to determine the ore's leachability. Bottle roll tests are usually conducted on reverse circulation drill cuttings samples (= 1/4 inch (6 mm) in size). Bottle roll tests provide initial information about precious metal recovery, recovery rate, and reagent requirements. The recovery results are to be considered maximums because attrition grinding creates fines and liberates recoverable values that would not be liberated from the material during a static leach. Bottle roll tests can be conducted on up to 25 lb (11 kg) ore charges of up to two inches (50 mm) in size. However, the coarser the feed the more attrition grinding occurs during rolling.

Jan 1, 1988

By F. Palmay, R. D. Gwilym, P. Eng

INTRODUCTION As the experience in Canada indicates, it is becoming more and more common to evaluate major mining projects, especially those relating to uranium, with respect to their environmental effects. As part of this evaluation public hearings are becoming the rule rather than the exception. In this area the 1970's and presumably the 1980's can be characterized as the age of "Environmental Assessments" or "Environmental Impact Statements" which form the basis of these hearings. These documents tend to require significant amounts of research, data collection and effort in their preparation, and tend to be closely scrutinized by the hearing body and by groups in opposition to the project. This opposition is becoming more organized and sophisticated. The assessment or impact document, together with the evidence supporting it during the hearings can: (a) mean the difference between a lengthy and hence costly hearing and a smoother, shorter and less expensive one, (b) result in requirements for extensive modification at the expense of the proponent to his project, (c) result in the proponent being required to carry out extensive studies, research or monitoring programs, and (d) conceivably may in certain situations result in the project actually being turned down. Therefore, while on the one hand it is important to have available technical answers to concerns relating to uranium, its associated and perceived hazards, it is getting more and more important to be able to present these answers in both a written and oral format in such a way as to meet the criticism and concerns of the opposition, be they citizens in general or special interest groups including environmental lobbyists. JURISDICTION From a Canadian perspective, the first legal question to be answered is which level of government has jurisdiction over uranium mines in general and specifically over aspects relating to the environmental effects, including the health and safety aspects, of uranium mines and

Jan 1, 1980

By M. Moss Stanley, Ronald P. Klepper

The objective of this chapter is to provide data that will assist in the selection and sizing of equipment utilized in the filtration method of separating solids from liquids. It should be recognized at the outset that in some situations more than one option may be available to achieve the target desired. In some cases purely technical objectives may be sacrificed because of cost considerations, design factors or other elements in order to satisfy optimization within the flowsheet and/or to provide bottom line results. Before considering available options, and prior to the next step of sizing out the selection, the operating criteria should be set down. The test work to develop selection and sizing data will be based on this data and the final products desired. This will help to establish initial parameters. A. GENERAL DATA 1. Material to be filtered: a. Solids b. Mother liquor 2. Feed rate of slurry in GPM 3. Density of slurry: Sp. Gr. Solids 4. Slurry: Temp. pH Viscosity 5. Source and method of feed 6. Valuable product: Solids Filtrate Both 7. Details on: Volatility Toxicity Stability 8. If flocculant is indicated, what has been used? 9. Describe product: (i.e., fibrous, cor 10. rosive, abrasive, inflammable, explosive, pasty, 11. Does product alter or require special environment during transport? 12. What type of filter media has been used successfully? 13. Is there any objection to use of a filter aid? If not, is there any preference? B. SOLIDS DATA 1. Sp. Gr. Bulk density 2. Screen analysis 3. Desired percentage moisture in cake 4. Solubility (state conditions): In mother liquor In wash water 5. Description of cake: (i.e., amorphous, fibrous, crystalline, colloidal, gran¬ular, thixotropic, 6. Special requirements for moisture de¬termination? 7. Can solids be compressed during dewatering? 8. Proposed product handling 9. Subsequent thermal drying or other pro¬cedure C. FILTRATE 1. Is separation of wash water and mother liquor desirable?

Jan 1, 1986

By Matteo Cortinovis, Giuseppe Gelmi

"INTRODUCTIONEdilmac dei F.lli Maccabelli (hereinafter referred to as Edilmac) has recently developed a special civil engineering application using the Raise Boring technology with the assistance of Inrock MGS (Magnetic Guidance System). Applying the Paratrack Magnetic Guidance System coupled with a directional mud motor to the drill string allows a better accuracy compared to standard drilling, as showed in our tests. This is the first time the Paratrack System has been applied to the Raise Boring technology. RAISE BORING METHOD STATEMENT The Raise Boring technology was born in North America during the Sixties. In 1962, Ingersoll and Robbins were the first companies to produce Raise Boring Machines (RBM). The technology was first used in the underground mine industry, in order to bore ventilation shafts and passes through different levels, thus reducing the cost of haulage. The Raise Boring method is only feasible in stable rock conditions. The Raise Boring method consists of drilling a small diameter pilot hole that reaches a tunnel located at the bottom of the drilled hole. Once the pilot hole reaches the tunnel, a reamer head is installed at the end of the drill string and pulled up, creating the hole with the designed diameter (Figures 1 and 2). The main equipment, which is required to perform Raise Boring activities, is the following: •,An RBM; •,A tricone bit; •,Drilling rods; •,A reaming head; The standard mucking of the pilot hole is done with water or bentonite mud. For the last 30 years, Edilmac has developed a mucking process, which uses compressed air with the addition of foam or a small amount of water for dust control.Pilot hole tricone. The drilling of the pilot hole is usually performed with a tricone bit having a diameter between 11” (27.61 cm) and 15” (38.10 cm) (Figure 3). High strength rods. They generally have a diameter ranging from 10” (25.40 cm) to 12 ?” (32.70 cm) (Figure 4), depending on the length and the final diameter of the shaft."

Jan 1, 2016

By M. H. Weinecke, B. P. Faulkner

This paper discusses the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last 10 years. Many claylike materials, such as coal fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce commercially salable LWA.

Jan 1, 2003

By F. F. Aplan, C. E. Raleigh

Three run-of-mine bituminous coals, ranging in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µm), -100 mesh (150 µm), and -400 mesh (37µm) feed particle sizes with selected pyrite depressants and a dispersant. For the three coals tested, pyrite and ash -forming minerals were usually rejected best at -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µm) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1992

By N. Ohmura, H. Saiki, T. Nagaoka

A microbiological flotation system that facilitates the removal of pyritic sulfurfrom coal is reported. The chemoautotrophic bacterium Thiobacillus ferrooxidans is utilized as a pyrite-selective biological surfactant that augments the flotation-mediated rejection of pyritic sulfur. The bacteria were produced by continuous cultivation in 50-L tanks, where it was possible to produce 3.8 x 1012 cells/day when the dilution rate was optimal and the pH was 1.6, a condition that prevented ferric precipitation. Prior to flotation, the bacteria were mixed with coal, which allowed cells to selectively adhere to the pyrite. The adherence of bacteria made the pyrite surfaces more hydrophilic, which facilitated separation by increasing the tendency of pyrite to sink, while the hydrophobic coal floated. When a synthetic coal/pyrite mixture (10.1 % sulfur) was subjected to microbial flotation, the level of sulfur rejection was stable during the entire period of operation (i.e., one hour). In the absence of bacteria, flotation reduced the sulfur content of a coal/pyrite mixture to within the range of 6.7% to 7.4%, with the combustible recoveries ranging from 93.9% to 99.0%. In the presence of bacteria, the sulfur content of cleaned coal was in the range of 1.3% to 1.4%, with the combustible recoveries ranging from 80.8% to 86.3%. Bacterial activity accounted for 57% of the total sulfur rejected through flotation. The desulfurization capacity of the system was further confirmed by testing it with run-of-mine coal. The pyritic sulfur content was reduced from 2.9% in the feed coal to around 1.2% in the froth product, while 80% of the combustible recovery was retained. Microbial flotation removed 60% of the pyritic sulfur from the feed. These findings demonstrated that micro¬bial flotation could be utilized for the removal of pyritic sulfur from coal in a semicontinuous system.

Jan 1, 2000

By Yoshio Hiramatsu

In Toyoha mine near Sapporo, the ground temperature is very high, perhaps due to inflow of hot mineral water, the origin of which may be rock masses intruded by the igneous activity in the Tertiary period. The rock masses are found about 2 km east of the mine, their temperature being estimated at from 770 to 870 K at a depth of 3 km. In this mine several veins bearing zinc and lead ores have been mined down to the depth of 300 m from the level of the main entry, of which altitude is 551 m above the sea level. Formerly no attempt was made at development of the deeper part of the mine than the 350 m level from the main entry. Let us indicate hereafter the levels in this mine in such a way that the level 300 m deep from the main entry is denoted as 300 mL. Since 1974, however, the 450 mL of Tajima vein has been developed by deepening No. 5 Shaft to, and by driving drifts in the level. Much hot mineral water has been flowing into the drifts from rock. After twenty-eight months from the beginning of development, the total length of excavation amounted to about 1300 m. The success in development so far may be attributed to cooling rock and air with chilled water and to adopting heat-resisting explosives and detonators. This cooling costed very much and for further development in this level a more effective and economical cooling is desired if possible. To obtain fundamental data for designing an economical cooling, the authors investigated, as a preliminary study, the heat balance in the main drift of 450 mL, by measuring the temperatures of air, rock, hot mineral water, the rates of flow of air and water and so on, in August 1976. They are now carrying out continual measurements of the variations in rock temperature, air temperature and humidity with time. The present paper describes the details of the preliminary study.

Jan 1, 1980

By Samuel B. Romberger

During the formation of most epithermal precious metal deposits geochemical changes can be characterized by the introduction of large amounts of silica, minor amounts of sulfur, and trace quantities of gold, silver, and other metals. During the same process, large amounts of alkalis and alkaline earth elements, such as sodium and calcium, and sometimes aluminum are removed from the rocks. In deposits hosted by carbonate sedimentary rocks large amounts of carbonate may be removed before or during the silicification process. Small amounts of iron may be introduced by the mineralizing solutions, however, in most epithermal deposits this may be a relatively immobile component and is locally derived. The results of these changes are deposits consisting of up to 90 to 95 percent silica as quartz veins, breccias, silicified host rocks, and jasperoids containing a few percent sulfides, mostly pyrite, and a few parts per million gold and silver. Other minerals commonly but not always present are barite, arsenic, antimony, or mercury sulfides, and tellurides. Often gold shows a spatial, and therefore an apparent genetic, relationship to pyrite in primary ores. Alteration and gangue assemblages sometimes include sericite and/or adularia, and parts of the deposits may contain alunite and/or clay minerals. Even though the value of these deposits usually lies in their gold content, silver is usually present in larger quantities than gold (Romberger, 1990). Based on these general characteristics observed in a large number of epithermal deposits, together with processes occurring in active geothermal areas to which they are often genetically linked (Henley, 1985), a model is proposed whereby deposition occurs along a subhorizontal zone separating environments of contrasting chemistries. The upper environment is characterized by oxygenated acid waters and the deeper environment by a reducing near neutral aqueous system. The model describes the chemical changes occurring as a result of mixing and/or boiling within this zone. It builds upon the physical models proposed by Romberger (1988a) for disseminated gold deposits and Bonham (1988; 1989) for volcanic rockhosted deposits.

Jan 1, 1990

By T. B. Whitmoyer, J. E. Sneckenberger, M. A. Jerabek, C. F. Stanley

The measurement of acoustic impedance at frequencies up to 6,400 Hz has been proposed as a diagnostic tool to yield more detailed information about lung condition. A three generation branching system of plastic Y-tubes has been constructed. The impedance of the branched system is measured by an impedance tube using the two-microphone technique. The impedance spectrum is used to calculate the reflection coefficient spectrum, which is converted to an impulse response by an inverse FFT. The area function is extracted from the impulse response by the Ware-Aki algorithm. Measurements of acoustic impedance of the branched system were made for several different end conditions of the eight terminal outlets. The outlets were either blocked with modeling clay, plastic packing material, or aluminum blocks or were unblocked. Six measurements were made of each configuration. In general, the more outlets blocked, the larger the shift to the right of the impedance magnitude peaks for frequencies above 3000 Hz. The impedance magnitude peaks for the plastic packing material were shifted in frequency to the right relative to the peaks of the other system terminations. The impedance magnitude peaks for the clay and aluminum system terminations were significantly different in magnitude but not shifted in frequency. The area functions at the end of the branched system were significantly different (a > 99%) for most of the end conditions. Area functions for the modeled branched lung systems between the end of the impedance tube and the termination outlets of the branched system were similar but distinctively different for the various end conditions. These results indicate that the two-microphone technique can sense small changes in the terminating end conditions of a rigid system of branched tubes and thus may sense impedance changes due to lung disease in the conducting airways. Keywords: acoustic impedance, lung model, area function.

Jan 1, 1991

By Carlos Kovacs-Figueroa

Because of air pollution control regulations in the early 701s it became necessary to clean effluent gases from the Morenci Reduction Works Smelter. Feasibility studies indicated that this could be accomplished most efficiently by using the smelter gaseous effluent to feed a sulfuric acid plant. Complying with air pollution control regulations thus created the need to dispose of relatively large amounts of concentrated sulfuric acid. Typical Morenci ores contain substantial amounts of oxidized copper minerals which are not recoverable by flotation. In addition, there is low sulfide, high oxide material which can be leached, but is not suitable for flotation concentration. Early in 1971 sufficent data had been accumulated to show that a leaching plant for the Morenci tailings could use a large portion of the sulfuric acid produced by the Smelter. It was determined that for all practical purposes leaching of the available copper was complete in two hours or less. Capital expenditures could not be justified for more than two stages of counter current decantation for recovery of the leached copper, and the plant was designed with these criteria in mind.

Jan 1, 1976