Search Documents

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By C. Allen, H. Zhang, L. Falk

Shock loss occurs when there is a change in the area of a drift or airflow direction. These shock losses accumulate throughout the ventilation system and will increase the mine resistance as underground development deepens or becomes more complex. Hence, shock losses should be carefully considered when establishing the resistance through a series of branches as they can be a significant contributor to the estimated mine resistance. Using computer software to simulate a ventilation system is common but applying reasonable shock loss factors in the software is not a simple or direct process. Determining shock loss values includes the consideration of historical measurements, application of factors and formulas from literature based on the geometry and complexity of junctions, and the geometry variation at different locations. For example, the shock loss at the bottom of a ventilation raise can consist of a 90° bend and a sudden area change. This paper presents an approach for estimating shock loss factors near raise junctions using computational fluid dynamics (CFD). Current and future work will also be compared with field measurements. Results from this approach are compared with software defaults as well as classical techniques in published literature and standards.

Sep 1, 2024

By Howard J. Haselhuhn

The effectiveness of selective flocculation and dispersion processes for the concentration of hematite ore are strongly dependent on the ionic content of the process water. It has been noticed that magnesium ions are more detrimental to iron recoveries during gravity separation and flotation processes than calcium. This phenomenon was studied by measuring the zeta potential of hematite ore at various concentrations of sodium, magnesium, calcium, strontium and barium at a pH of 11. Results show that zeta potential inverts from negative to positive at concentrations as low as 0.16 mM of magnesium ions in the solution. It takes a significantly higher concentration (1.25 mM) of calcium ions to achieve the same effect. This difference is attributed to the ability of magnesium ions to adsorb to all surface hydroxyl groups, whereas calcium, due to its larger size, can only adsorb to every third hydroxyl group. This hypothesis was confirmed by results similar to those seen with calcium when this test was repeated with strontium and barium ions. The tendency for calcium ions to adsorb to every third surface hydroxyl group causes higher concentrations of calcium to be less detrimental to hematite concentration processes than magnesium.

May 1, 2012

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By Daniel H. Knepper

Estimating the lithologic composition of gravel deposits for aggregate quality using standard field and laboratory techniques is costly and time-consuming. As an alternative, digital geologic maps and elevation models may provide a means for predicting the lithologic composition of channel and terrace deposits. Digital geologic maps can be used to evaluate the distribution of map units: their geomorphic setting, and the physical properties of the gravel source. To test this concept, the lithologies and topography of the upper drainage basin of the Big Thompson River along the Colorado Front Range were used to examine various factors that may control the final lithologic composition of channel and terrace gravels downstream. The simplest factor is the area of each of the map units in the upper drainage basin area, which can be easily measured from the digital geologic map. The percentage of each map unit within the total area provides a estimate of the pro- portions of each map unit that might be expected to occur in the downstream gravels. Published estimates of the hardness and durability of each map unit were used to calculate physical property-weighted areas; these areas are an estimate of the potential of each unit to be eroded and transported as gravel-sized particles. The areas of each map unit at 1-kilometer intervals from the drainage basin exit point were used to calculate a distance-weighted area for each map unit. For this study, a simple inverse relationship (area/distance) was used for distance weighting, but a more complicated distance function may ultimately be required. The topographic setting of exposed rock units should exert a significant influence on whether material will move slowly or rapidly through the drainage system. Two topographic factors were examined: gradient and slope. A simple gradient between map unit occurrences and the exit point of the drainage basin was used to calculate a gradient-weighted area estimate for each map unit. The slope-weighted area estimate uses the slope steepness (in degrees) in the immediate vicinity of each map unit occurrence as a measure of the tendency of material to begin moving into the sediment transport system. The primary intent of this study was to test the concept of using digital geologic map and elevation images to estimate gravel composition, rather than actually producing a useful analysis of a drainage basin. Each of the controlling factors was examined independently to gain an understanding of the magnitude of the effect of each factor. Ultimately, a comprehensive predictive model will be constructed using a combination of the various controlling factors.

Jan 1, 2001

By B. K. McMahon

Block caving is an efficient mass-production method for the underground mining of large orebodies. However, the block-caving method requires a substantial investment in developmental works, based on the assumption that the rock will cave. Efficient block caving is prevented if the rock forms stable arches or breaks into fragments that are too large to pass easily through the finger raises. Under these conditions, the cost of the additional labor, drilling, and blasting required to assist caving may be sufficient to make marginal orebodies uneconomic or alternative mining methods more attractive. Reliable methods for the prediction of the block-caving behavior of an orebody are clearly needed at the initial planning stage. These methods should be capable of considering both geological and engineering aspects of a block cave, as experience has shown that the manner in which a block cave is initiated and developed may be almost as important as the geological conditions such as the nature of the rock material, degree of alteration, characteristics of the joints and faults, etc. The initial state of stress in the rock mass should also be considered.

Jan 1, 1969

By R. M. Ocampo-Franco

The line seven, as part of the development of the Subway Master Plan in Mexico City, will tunnel under different subsoil conditions of clay with high water content and low shear resistance located between 8 and 12m beneath the surface. Boulders in silty sand and gravel to a 40m depth underlay this stratum. Economics, scheduled time of construction, and the obligated interconnection with existing lines one and two determined the construction of the tunnels to have an overburden of 1.0 to 2.2 times the diameter. In the north part of line seven there is a track of 251m length that was decided to attack with an open shield of 9.14m of diameter due to the characteristics of the sub-soil, minimum section needed as well as a minimal overburden, of 10.41m. The paper explains the construction procedure from the excavation stage to the reinforcement of the final lining obligated for the ground subsidence as a result of volumetric changes of a stratum of 4m thick of clay overlying the crown of the shield. Manuscript not received in time for publication.

Jan 1, 1983

By Kenneth L. Schellie

In preplanning the reclamation of a pit or quarry the geology of the site is the name of the game! The planner must know the parameters of the deposit, the quantity and kind of earth materials to be removed, and the amount and nature of the materials to be left behind or wasted as the result of processing the marketable product. With many states and most local jurisdictions requiring reclamation plans prior to the issuance of mining permits, the need for accurate and complete data concerning the geology of the site becomes increasingly important. The producer need only know that marketable materials are available in sufficient quantity to make the mining operation economically feasible-the planner, in order that the land may be reshaped for a useful purpose, must have reasonably precise information as to the dimensions and configurations of the pit or quarry following extraction and the amount and type of materials available on the site (or in some cases offsite as well). Therefore the geology of the site is of major significance in determining the land forms and use capabilities of the property upon completion of the mining process.

Jan 1, 1974

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By Stuart Hammer

The mining industry has seen a flurry of merger and acquisition activity of late. Rising metal prices, increased spending on infrastructure in developing nations and the growing demand for companies to diversify have helped fuel M&A activity in this industry. Many analysts believe that the robust M&A activity will continue, particularly if the demand for mineral resources in India and China remains strong. Because prospective purchasers need to evaluate the various risks confronting target companies, acquiring mining companies requires a considerable amount of due diligence. Of these risks, environmental risk is critical and warrants significant analysis. The failure to properly assess environmental risks associated with remediation, reclamation, compliance or litigation can undermine the transaction. Such assessment is a difficult endeavor, however, due to several challenges that companies face when assessing environmental risks. To make matters more complicated, despite these challenges, many sellers ask buyers to assume all environmental risks with limited post-closing indemnification rights. This article addresses the most significant issues that commonly arise when conducting environmental due diligence and allocating environmental risk in connection with M&A transactions in the mining industry.

Jan 1, 2008

By G. Van Weert, J. F. Breedveld

Both regular and Silver Impregnated Activated Carbon (SIAC) were studied for their effectiveness in removing WAD (Weak Acid Dissociated) cyanides from solutions at pH = 10. SIAC has already been shown to be effective in the removal of free cyanide down to 30 ppb or less. The present work deals with complexed cyanides. Zinc cyanide was used to represent the WAD component. At pH=10, in either batch or column tests it was not possible to lower the total cyanide in solution from either 30 or 8 ppm to less than 1 ppm, using SIAC, regular activated carbon as received, or after grinding. Silver (metal) impregnation of the carbon was not beneficial in the removal of WAD cyanide. However, when silver is added as silver ions (nitrate), the cyanide is adsorbed as silver cyanide in preference to zinc cyanide. The latter compound converts to zinc (hydr) oxide. This way, the cyanide concentration in solution can be lowered below 1 ppm, even when zinc cyanide is already adsorbed on the carbon used. A single exploratory test with added copper ions indicated a similar effect for that system.

Jan 1, 2004

By Wang Yingmin, Xu Zhuyun

There are 3 steps in the process of forming a mine ventilation system, (1) selecting a reasonable ventilation pattern (included pit shaft arrangement); (2) optimizing of the ventilation network and (3) computing and outputting the flow splitting results of the network with the optimal ventilating equipments selected. In the past, the first step was relied on artificial decision-making. In order to design a common ventilation system, some ventilation experts were needed to participate or do some examinations. Even so, the design made was reasonable only for those experts. If there is a mistake in the first step, then even the followed 2 steps are best done, the losses are very difficult to retrieve. So that, the first step is very important. The development of expert systems provided an efficient means and tool for all engineering fields. This paper presents an expert system of selecting mine ventilation pattern and pit shaft arrangement. After testing many times, it is shown that the system can perform the first step of designing a mine ventilation system, and can help the experts doing their study works more efficiently.

Jan 1, 1991

By Shaning Yu, Yosry A. Attia

The purpose of this work was to investigate the feasibility of using column flotation as a floc separation technique. In this study, the ultrafine coal (minus 25 microns) slurries were cleaned by using the Integration of column flotation with selective flocculation. It was found that using column flotation as a floc separation technique during the "cleaning" stage, achieved much better results than that either using column flotation as a rougher separation technique for coal flocs, or using It directly to recover the ultrafine coal from the slurries without adding selective flocculant. Thus, the ultrafine coal slurries were first separated by selective flocculation process to reject a certain amount of the dispersed ultrafine ash minerals, and to aggregate the ultrafine coal particles as flocs. Thus, the entrainment of ultrafine ash minerals Into the coal floc-froth concentrate during flotation could be considerably reduced. Subsequently, the coal flocs were further "cleaned" by column flotation. The experimental results Indicated that this approach was technically feasible and particularly suitable for a slurry containing a large amount of ultrafine particles. The effect of flotation time, and collector dosage on column flotation of coal flocs were also Investigated and reported In this article.

Jan 1, 1988

By C. L. Karr

Researchers at the U. S. Bureau of Mines have developed a technique for producing adaptive control systems using fuzzy logic and genetic algorithms. These controllers can be used to efficiently manipulate complex systems in real-time. Furthermore, they can achieve an acceptable level of control despite limited feedback in the problem environment. The control systems that result from the implementation of the Bureau-developed technique are able to recognize when changes have occurred in the problem environment, evaluate the magnitude of these changes, and alter the strategy being used to control the problem environment. Fuzzy logic is used to provide the controller with a rule-base that mimics the "rule-of-thumb" approach generally adopted by humans in the area of process control. Genetic algorithms are used to provide the controller with the adaptive capabilities necessary for the control of complex time-varying processes popular in the minerals processing industry. The effectiveness of this technique is demonstrated on a laboratory pH titration system. The pH system includes a changing setpoint, titrants with varying concentrations, and the possible addition of a buffering solution.

Jan 1, 1993

By Munson R. McKinney, Bryan A. Slim

To date some 1,000 exploration targets (by way of adits, mine dumps, shafts, outcrops and unstoped mine areas) have so far been identified using an interactive data base system to query a digital data base comprising topographic, cadastral geological and mine components developed as a compilation of old plans, records, surveys and recently flown aerial photography. The exploration targets are intended for early follow-up as part of a 1987 exploration programme to investigate the reserve potential of the former producing property located in southern Utah. Of further interest is the unscrambling of old mine plans to provide drill targets for investigation of unstoped reserves with one target being a possible 800,000 tons in part of the lower workings. The project site encompasses about 3,200 acres of mainly patented lode claims covering most of the claims and mines of the Gold Mountain mining district formed in 1889. Turn of the century mining saw several mines operating whose total production was at least 143,000 oz. gold and 460,000 oz. silver from steeply dipping veins up to 20 ft. or more in thickness.

Jan 1, 1987

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

One of the major objectives of cost analysis is to enable the manager to predict the financial outcomes of decisions. To accomplish this, the future costs and benefits of alternative courses of action must be determined. If care- fully used, information about past financial performance can be helpful in this analysis despite the fact that, by definition, financial reporting information is historical. In many cases, both revenues and costs need to be estimated for decision- making. For the production manager, additional revenue is a result of increased throughput or recovery of valuable material from the stream of mined material. A reduction in operating cost, although similar to a revenue increase in its financial impact, is estimated using slightly different techniques. Generally, the estimation of cost is more difficult than the estimation of revenue. Most cost estimates have two components: an estimate of fixed costs and an estimate of variable costs. As discussed in chapter 5, the total cost of an activity during a specified period can be expressed as: Total cost = (Variable cost per unit of activity) x (Units of activity) + Fixed cost or TC = VX+F

Jan 1, 1999

By William D. Hanson

Celestine (celestite) (SrSO4), the primary ore mineral of strontium, is present in the DeQueen Limestone Member of the Trinity Group (Lower Cretaceous) in Sevier, Howard, and Pike Counties, southwest Arkansas. Two mappable celestine beds have been identified. One bed is commonly 3-5 in. thick, but ranges up to 18 in. in thickness; the other bed is generally 2-3 in. thick. The beds are concordant within the DeQueen Limestone and were formed by precipitation from periodically restricted sea water. Reports concerning celestine date back to 1929, when Hugh D. Miser and A. H. Purdue mapped the geology of the DeQueen and Caddo Gap quadrangles. A small amount of celestine was produced in the early 1940s in Howard County. During 1941, the J. W. Hintze Company collected 1,500 pounds of celestine for testing purposes. In 1942 and 1943,750 test holes were drilled by the Bennett-Clark Company in Howard County. Afterward, approximately 90 tons of celestine was open-pit mined and shipped to Texas for processing. Since then, no mining of celestine in Arkansas has taken place.

Jan 1, 1999

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs&apos; dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA&apos;s unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991

By T. M. Barton

This paper presents several case studies in which a mechanics-based boundary-element program is used to back-calculate the surface subsidence associated with various panels at several northern Appalachian coal mines. The program used in this case study is called LAMODEL, which incorporates a frictionless, laminated overburden into a general-purpose displacement-discontinuity code primarily designed for calculating the stresses and displacements in coal mines or other thin-seam or vein-type deposits. In this paper, the program is used to calculate both the underground convergence and the resulting surface subsidence at five longwall panels and a room-and-pillar section. The fitted subsidence from the model is compared with the field measurements and analyzed. The results from this work show that the LAMODEL program is not as accurate as available empirical subsidence-predictive methods; the expected correlation between the geology and the optimum input parameters is not evident. However, for a mechanics-based program, LAMODEL does provide moderately accurate subsidence calculations, and it is one of a few programs that can even attempt to practically calculate both underground stress and convergence and the resulting surface subsidence.

Jan 1, 2000