Search Documents

By R. P. Benson, D. H. MacDonald, D. R. McCreath

1 - INTRODUCTION The Canadian Shield is well known as being among the older exposed areas of the earth's surface. Except for local zones, its extent from the Arctic to central North America is characterized by strong and durable crystalline rocks. It is generally regarded as highly competent for tunnelling and underground excavation and, as a result, many openings are excavated in it with minimal temporary support. If hydraulic efficiency is not a factor, tunnels do not usually require continuous concrete linings. A high percentage of the crystalline rocks of the Shield are of metamorphic origin and as such one of the dominant characteristics is their foliation. Zones of sheared or faulted rock are common in the Canadian Shield, particularly in association with foliation. These zones may be created during the late stages of the metamorphic process, leaving shear zones as an integral feature of foliated rock. As foliation is a preferred direction of weakness, deformation and rupture during subsequent tectonism may also create parallel shear zones. These "foliation shear zones", as described by Deere (1973), are an adverse feature of the otherwise durable rocks of the Canadian Shield. The zones may range from faults of major proportions to seams only a fraction of an inch thick. If fault gouge or alteration products exist in the zone the strength of the rock mass may be great1y reduced. As foliation is usually continuous, large unstable wedges of rock may be created if the opening is subparallel to the foliation. The effect on the construction of underground openings in terms of excavations, support and scheduling can be significant.

Jan 1, 1974

By Henry Antwi

The decade of the 1990s promises to be one of increasing internationalization for domestic minerals producers as they scramble to enhance relative positions in highly competitive, international minerals markets. This "international mining rush" is fueled by developing countries seeking international investment capital to explore for, develop and exploit sizable mineral endowments in an attempt to support the increasingly popular, but expensive, wave of democracy and selfdetermination sweeping the world. This "fuel" typically takes the form of revised mining codes and, often, lucrative investment incentives. These incentives include favorable tax rates, royalty provisions, relaxation of import/ export constraints, depreciation schedules, profit repatriation and other variables that can positively impact mineral investment decision making. Concomitantly, in their attempts to address real and perceived short- and long-term woes associated with enhancing competitive positions internationally, many domestic explorers and producers are attracted to the prospect of finding high-grade deposits in relatively virgin areas. Combined with the investment incentives provided by foreign governments, these high-grade deposits promise lucrative potential returns from projects having short payback periods. Classic examples of this mutual desire to intensify international mining efforts by domestic producers are illustrated by activity levels in countries like Chile, Bolivia and Venezuela in Latin America and, more recently, in Eastern Europe and select locations in the former Soviet Union. As US corporations scurry to send fact-finding, technical, evaluation and financial teams to these presently popular locations, one area of the world has received little attention - Subsaharan Africa. Specifically, the country of Ghana (formerly the Gold Coast) deserves more attention than it appears to be receiving from North American mining companies.

Jan 1, 1992

By Etienne Simode

When a fire breaks out in a mine access road, the hot smoke, due to heat transfer with the surrounding strata, progressively cools as it moves forward. Depending upon the resulting temperature distribution, the density of the fluid changes. This change will bring about: Firstly, a variation in the resistance of the roads, a static factor which will affect ventilation flow rates; Secondly, the appearance of extensive aerodynamic driving loads in the vertical and angled roads, a dynamic factor which can have an extensive impact on ventilation. Because of the appearance of combustion and distillation products, the vaporization of water, which wets the timbering and strata, and the expansion of gases, fluid rates can at times be increased tenfold in the area of the fire. These disturbances may cause explosions and ventilation inversions, which fill other working areas with smoke toxic to workers, and which can come up upon rescue teams from behind. Due to the progressive heating of the surrounding rocks, which will slow down heat transfer, these dangerous conditions change over time. At the Lorraine Basin Coal Mines, programs have been set up and employed for the computer simulation of these phenomena over time. They serve to anticipate or to understand such phenomena, the input data being the characteristic parameters of the mine ventilation network, the operating curve of the main fans, and measurements or estimates of some temperatures. Two programs, employed together, have been developed for these studies: One program, called RESO, calculates the distribution of flow rates and pressures throughout the entire network; The other, called FEUMIN, determines smoke temperatures over their entire path.

Jan 1, 1980

By Joe Komadina

DOUG HALBE: Our next topic is one that I would think everyone might want to contribute to. I'm sure everyone here has had some experience in this area. If you haven't, I'd suspect you've never really run a mill. This is what we call "Horrible Spill Areas We Had When We Started Up the Plant and How We Fixed Them." Our next speaker has had a really great operating career. He had many years with Newmont in the Carlin area, and now he's executive vice president and chief operating officer of Independence Mining Company: Jim Komadina. I don't have to be nice to the speakers anymore, do I? [laughter] You may wonder why we picked Jim Komadina to give this talk. I was involved many years ago in the start-up of Newmont7s Gold Quarry plant. Jim held quite a responsible position there. I'm not going to say anymore, but I have in the back of my mind this picture of the pump floor and a rowboat and a guy rowing around on the pump floor. [laughter] Jim, was that you? [laughter] JIM KOMADINA: Probably. I wasn't responsible for the design. [laughter] Actually it's amazing. I've seen a lot of these plants and actually had the opportunity to walk around them, so when I say this, "Horrible spills I have seen and done," it's because I've been responsible for more than my fair share of them. But having seen a lot of spills, I will present a little bit of wisdom about how to prevent them.

Jan 1, 1998

By P. Malozemoff

Discussion by P. Malozemoff I have no objection to using mathematics in the value appraisal of properties. The factor that is not emphasized in the paper is that very few important properties have a lifetime that reflects the initial ore reserves of the property divided by the rate of production adopted. In the majority of cases, major properties mine out several times the initial reserves. How much more will be mined out is not known, and only exceptionally gifted geologists can predict that additional reserves will be found. There is the further factor of metals price, which, over the long term, is not predictable. Another factor vitiating making calculations on initially established ore reserves is the speculative nature of exploration success. In my judgment, the life of a property, in addition to an established ore reserve, should include ample time for exploration to find additional reserves. The likelihood of additional reserves is based on the geological promise of the general area where the mine is established. This is especially important because of various risk factors associated with small orebodies, the economic life of which is about five to seven years. In underground mines, it is not economic to develop reserves beyond a certain depth, so the life of initially established reserves must be limited. In these cases, it is especially important to have a good geological understanding of the orebody and its continuity. To accommodate these concepts and present proof of economic soundness for a mining enterprise, a mathematical analysis should yield a life long enough to allow exploration and the development of additional reserves that would ensure a longer mine life and a more profitable result.

Jan 1, 1994

By Larry Snyder, Levent Ozdemir, Charles Fishman, Fun-Den Wang

Tunnel Boring Machine Instrumentation A 9.17 m. diameter tunnel boring machine presently in operation in Chicago, Illinois, has been instrumented to continuously monitor and record machine thrust, torque and penetration rate during boring. A micro-processor-based data logger capable of monitoring up to 60 channels of data digitizes and converts into appropriate engineering units the signals from various transducers mounted on the machine. The output from the data logger is sent to a teleprinter, providing a permanent record of measured data. The program control enables the data logger to scan all data channels at desired time intervals. Data obtained to date have been analyzed to determine the interrelationships of the parameters measured. Penetration rate was found to increase linearly with machine thrust with a unit increase in thrust causing more than a unit increase in penetration rate. For low thrust levels corresponding to the initial stages of a boring cycle, the penetration rate was observed to behave erratically until the thrust pressure was sufficiently high for the cutters to establish full contact with the tunnel face. Torque showed a curvilinear increase with machine thrust, reaching the design rating at about 70% of maximum available thrust. No-load torque was approximately 20% of the machine's rated torque capacity. Overall, the trends observed in measured machine parameters correlated closely with those predicted from experimental and theoretical boreability studies. In summary, the instrumentation system has mett two basic goals. First, it provided extensive and accurate boring data and secondly, it has proven that an automatic data acquisition system can be installed on a TBM and can function under adverse environment.

Jan 1, 1979

By S. D. Morrison, J. L. Watson

It is well known that the density and viscosity of a mill pulp have optimum levels for grinding efficiency, and sophisticated control loops are employed to control pulp density in industry. However, these control loops rely on a number of plant measurements, and often the input data will not permit effective determination and control of the mill pulp density. The use of a single remote pulp density measurement has obvious advantages, and it is suggested and demonstrated for laboratory batch grinding that mill noise measurements can indicate the effective density of the mill pulp. In addition, the mill noise is shown to indicate the actual effective pulp viscosity in the mill and hence permit the identification of the dynamic rheological regime existing in the mill. It is demonstrated that mill noise increases with grind time and, at any given grind time, with increasing pulp density in the pseudoplastic range. This increase in mill noise level with pulp density is interpreted as indicating a decreasing pulp viscosity. The results show that the transition from dilatant to pseudoplastic conditions within the mill, with increasing pulp density, can be identified by this increase in mill noise. When the pseudoplastic pulp started to exhibit yield characteris- tics, the mill noise fell dramatically. The technique of mill noise analysis is then used to investigate the effect of a grinding additive on the batch grinding of two ores. With a magnetite ore, the additive was shown to increase the mill noise, and hence decrease the pulp viscosity, in the pseudoplastic region and to increase the effective grinding. The molybdenite ore, however, did not show significant noise level changes and did not show improved grinding efficiency.

Jan 1, 1987

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By N. B. Aughenbaugh

A study was made to determine those petrographic parameters that are correlative with carbonate-aggregate quality as indicated by the Los Angeles abrasion and absorption tests. Samples collected at 28 sites in northern and eastern Indiana were analyzed petrographically, chiefly for void content, grain size, grain-size variation, grain shape, and grain interlock. Most of the sampled sites are in the belt of Silurian rocks of east-central and north- western Indiana. Though a few sites lie outside this belt, most of these have only a thin Devonian section above the Silurian. Three sites are non-Silurian and are included for comparison. Most of the samples studied are from Middle and Upper Silurian units. Both biohermal and nonbiohermal facies are included. The biohermal rocks are typically dense but vugular, finely crystalline granular dolomite. Nonbiohermal facies are porous, medium to coarsely crystalline, granular dolomite with dolomite rhombs The Los Angeles abrasion losses ranged from 20 to 46 per cent, the rocks in the eastern part of the state showing the higher values. Absorption tests indicate the same general quality trend. Comparison of petrographic studies with Los Angeles abrasion- and absorption-test results indicate the following correlations. (1) As per, cent of voids increases, quality decreases. (2) As average grain size increases, quality decreases. (3) Variations from mean grain size appear to have no effect on the quality. (4) As angularity and roughness of the grains increase, quality increases. (5) As grain-to-grain interlock increases, quality increases. Variations in the calcium-magnesium ratio have no apparent effect on aggregate quality, except as they affect the texture.

Jan 1, 1966

By Leonard G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups: that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mm) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh (< 0.60 mm); in fluidized bed uses, the coal is typically < 8, in. (< 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1 to 2% in. (25 to 63 mm). Coal preparation plants typically work with a coarse size fraction of 6X 1/14 in. (150X32 mm). The past decades has shown a steady increase in the tonnage of coal cleaned, 1 but it seems probable that the next decades will produce much wider applica- tion of deep coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is intimately connected with the size of coal, a systems design engineer will need as much information as possible concerning the size distributions produced by different types of machines and how these can be modified by different ways of operating the machines. In general, the following questions will be of concern: 1.What type of crusher or grinder is best, or most satisfactory, for reducing a given feed size and type of coal to a desired product size? Frequently, the desired product is smaller than some nominal size, but with as few fines as possible, or the fraction in some size range has to be as high as possible. 2. How big does the machine have to be for a given throughput rate? 3. How much electrical energy (or its equivalent) is required per ton of product? 4. How does the size distribution vary with change in throughput rate, and is a control scheme necessary or desirable? 5. Can the size distribution be readily varied if desired? 6. What is the optimum way to operate a machine in a given system? This section will emphasize certain general principles which guide us in answering these questions. PARTICLE SIZING Since particle size and size distribution are the raw information with which we work, it is worthwhile to review the terminology used. In this regard, see

Jan 1, 1991

By Jeffery Denit, Steve Hoffman, Van Housman

The Environmental Protection Agency (EPA) is in the early stages of developing a national mining waste program. Our goal is to develop a mining waste program that will be state implemented, multimedia in nature, flexible, utilize and enhance existing state programs, and protect the environment. The Agency appreciates the cooperation the mining industry is providing through its participation in the Policy Dialogue committee on Mining and by providing the Agency with technical data. The following is a discussion of what led to the development of a national mining waste program, the agenda initiative to evaluate Toxic Substances Control Act authority in phosphate manufacturing, and the important steps being taken through the Policy Dialogue process to frame and discuss issues. EXTRACTION AND BENEFICIATION OF ORES The Resource Conservation and Recovery Act of 1976 (RCRA) and subsequent amendments created a framework for the regulation of hazardous wastes under Subtitle C and nonhazardous waste under Subtitle D. In 1978, initial regulations were proposed for hazardous waste management units under RCRA. These identified a universe of special wastes that were large volume, low hazard and less amenable to Subtitle C control techniques. EPA noted that waste materials from the "extraction, beneficiation and processing of ores and minerals m fit these criteria. In October 1980, Section 3001 of RCRA was amended. This Bevill amendment excluded solid waste from the extraction, beneficiation and processing of ores and minerals from regulatory control under RCRA&apos;s hazardous waste Subtitle C. This was done pending a report to Congress and a regulatory determination regarding the Subtitle C status of these wastes. Thus in November 1980, EPA published an interim final amendment to the RCRA Subtitle C regulations to reflect the Bevill amendment. RCRA requires EPA to perform studies and make reports to Congress regarding the management methods and potential hazards of managing waste. RCRA also calls for a regulatory determination regarding whether Subtitle C (hazardous) or D (non- hazardous) controls are warranted for these wastes. In December 1985, EPA submitted a report to congress entitled, “Wastes from the Extraction and Beneficiation of Metallic Ores, Phosphate Rock, Asbestos, Overburden from Uranium Mining and Oil Shale." In that report, EPA found that some mining wastes exhibit hazardous characteristics, that the range of risk from mining waste is broad, and that waste management practices have caused environmental damage. In July 1986, EPA published a regulatory determination based on information gathered in the 1985 report to Congress and comments from interested parties. In the report, EPA concluded that RCRA Subtitle C regulation of extraction and beneficiation wastes was unwarranted because mining wastes tend to be disposed of in arid climates, waste volumes are high, and facilities and wastes are located in sparsely

Jan 1, 1992

By Otis M. Clarke

The 34th Forum on the Geology of Industrial Minerals gave members a chance to see the geology of various stone and ore deposits displayed graphically in quarry walls and also provided an opportunity to hear and see first-rate papers and posters on the geology of industrial minerals. Also, some field trips passed through areas of spectacular scenery. As a bonus, participants saw scenic mines, some of which are "pretty as a picture." Watercolor paintings prove it. At the Oklahoma Forum, the writer displayed a number of paintings of mines and other landscapes seen during previous Forum trips. These paintings and this brief article are part of a crusade to prove that some mines and geologic vistas are scenic wonders and belong in our visual heritage. It is a plea to save some of our best geologic exposures for future geologists, tourists, and artists.

Jan 1, 1999

By D. J. Simbi, T. R. C. Fernandes, M. Nyamhunga

The recovery of P2O5 from a 90-95% minus 45 microns phosphate slimes sample was carried out in a 5.08-cm internal diameter and 549-cm high flotation column cell. The influence of the feed rate, feed percent (%) solids, and frother dosage on the recovery was investigated following a truncated cubic 3 level by 3 variables experimental design. Two three-variable interactions of feed rate (-l)/feed percent solids (+l)/frother dosage (-1) and feed rate (-l)/feed percent solids (-1)/ frother dosage (+I) gave the region of optimum column performance: recovery (52.60-74.50%), mass yield (15.68-18.80%), and concentrate grade (22.87-31.2196). The collector dosage also showed a significant influence on the column performance. The high reagent consumption relative to the current plant levels points to the need for the removal of ultrafine particles (<10 µm).

Jan 1, 1999

By Luís Tavares Ribeiro

Nowadays there is a greater need for detailed reservoir modelling in the oil industry. It is generally recognized that nearly all reservoirs are heterogeneous and idealization of rock characteristics in flow calculations is unrealistic regarding actual physical and textural conditions encountered in geologic formations. The heterogeneity of oil reservoirs considerably influences the distribution of fluids, as well as their displacement. It would be advantageous if a reservoir petroleum engineer was able to construct a precise mathematical model of the detailed reservoir rock variability characterizing the degree of reservoir heterogeneity in an unambiguous way. This paper presents a geomathematical model describing the spatial behaviour and distribution of the principal reservoir properties. The model is based on the Theory of Regionalised Variables and the Kriging technique. The model is performed by a set of computing programs and is tested on an Abu Dhabi oil reservoir in United Arab Emirates.

Jan 1, 1986

By Pat Gochnour, Jim V. Rouse

Advances in the design and construction of heap­leach pads and process plants have greatly reduced. the potential for accidental releases of process olut1on. While workers in the field, and regulatory agencies such as the EPA have long recognized that the potential effects of any spills would be short term in nature due to cyanide attenuation and degradation (Engineering-Science, September, 1986, Pyrih, 1990, Rouse and Pyrih, 198, Rouse and Pyrih, 1991 ), unfortunately the general pubhc has held a perception that such a spill would be an environmental catastrophe. Few factual data on actual accidental releases have been available to dispel such a concept. Such data now exist and shoul? be disseminated to show that prompt response, using a combination of chemical oxidation, natural attenuation, and enhanced biodegradation of cyanide, can limit the effects of such rare releases, in both time and space.

Jan 1, 1992

By Shahzad Moosa, John M. Pitt

Statistical variability in rock strength can be evaluated by rapid, inexpensive ultrasonic pulse velocity measurements, an important consideration since rational probabilistic design in rock is often hampered by the cost of obtaining sufficient strength data. Experimental ultrasonic pulse velocity measurements on a set of 96 limestone specimens showed two distinct statistical populations. Both populations followed Weibull distributions, with flexural strength distributions paralleling pulse velocity distributions. Thus, experimental results suggest that strength variability may be predicted from a few rationally selected strength measurements and several ultrasonic tests. The correspondence between strength and velocity may then be used to develop an experimental transformation function, allowing the development of a statistical distribution function for strength based on the known statistics of velocity. Comparison of experimental groups with full sets of corresponding strength1 velocity data showed the technique offers a fairly accurate description of the statistics of strength.

Jan 1, 1986

By Donald L. Bott

A computer model called the Quality Compliance Model was developed to optimize the mine planning and sequencing in area coal mining with respect to the limit on pounds of sulfur dioxide per million BTU imposed by regulations. The objective of the model is to maximize the amount of high sulfur coal mined from various benches while meeting the specified compl&apos;ance standards. Given multiple seams and multiple benching operations, the mining sequence from each pit is simulated. The rate of mining is controlled such that the in-pit blending will maximize the usage of high sulfur coal and meet compliance standards. The compliant coal can be stockpiled for usage at a later date, or it can be disassociated. This calculation can be based on any given rate of production, i.e., from as small a unit as a unit train to as large as monthly or yearly production.

Jan 1, 1982

By Frank K. Mattson

The Minerals Processing Section of Surface Combustion is currently engineering and erecting a plant designed to produce 400,000 LTPY of 95% metalized pellets from raw magnetite concentrate, This venture is the first domestic commercial facility that will manufacture pre-reduced pellets as an integral part of a process to produce steel. Surface Combustion has developed the methods that will be used. Midrex, a division of Surface Combustion&apos;s parent company, Midland-Ross, will own and operate this plant. The site is adjacent to the City of Portland, Oregon on a 15 acre hydraulically-filled area on the east bank of the Willamette River. Either filter cake or concentrates in slurry form will be purchased from Marcona in Peru, delivered to the dock facility by ocean vessels and distributed to a pond for wet storage. Reclamation from the pond will be with a conventional dredge delivering concentrate to a thickener.

Jan 1, 1968

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004