Search Documents

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By Michel Grenier, Gopal Kunchur, Stephen Hardcastle

This paper presents the findings of a dust study in a typical fluorspar processing plant. The primary purpose of this study was to identify employees and occupational groups exposed to high dust levels and determine compliance with personnel regulations for regular and extended work shifts. The range of airborne concentration of respirable silica and fluoride compounds in specific areas and on personnel was determined. State of the art dust monitoring equipment and tracer gas techniques were used to measure dust concentration, pinpoint dust sources and map major airflow trends in the mill. Results of the survey indicated silica dust concentrations in excess of permissible limits being produced mainly by crushers at the south end of the building. Tracer gas releases and gas chromatographic analysis further showed that prevailing south to north air currents tended to carry and spread dust produced by the crushing operations throughout the process plant. Airborne concentrations of fluoride compounds measured during the study were always well below the prescribed threshold limit value (TLV) for the contaminant. Recommendations, including a mechanical exhaust ventilation system on crushers and transfer points, scheduled preventive maintenance on existing bar sprays and wearing of personal protective equipment were made which significantly improved the work environment. Further testing conducted after Installation of the dust extraction system revealed significant improvements in most areas of the mill.

Jan 1, 1991

By Jair Carlos Koppe, João Felipe C. L. Costa, Luis Eduardo de Souza

United Nations (UN) has been leading an international committee to define the guidelines in reporting resources and reserves. The system proposed by UN is very similar to the guidelines currently in use in Australia known as JORC guidelines (Joint Organisation Reserves Committee). The JORC guidelines show major differences in relation to the Brazilian system current in practice. The important aspects differing JORC from the current Brazilian guidelines for reporting reserves is the required sampling spacing. The JORC system requires the points of observation to be closer spaced than the Brazilian system for any class of resources. All classification systems share some common aspects in terms of defining the classes of resources based on distance separating samples and on the degree of confidence or accuracy associated with the results reported. Despite of being very clear in terms of stating sample distances, all the systems of classification do not provide clear definitions on how confidence limits should be calculated. This paper proposes a geostatistical framework to measure the uncertainty associated with the reported tonnages and grades. Results demonstrate that the error associated with an estimate can be approximated using multiple simulated deposits to define confidence limits. The methodology is illustrated in a large Brazilian coal deposit and proved to be appropriate to address the issue of quantifying the uncertainty necessary to be incorporated in the systems of reserves classification.

Jan 1, 2002

By Terry S. Maley

Federally owned mineral deposits generally fall into one of three categories: (1) minerals locatable under the General Mining Law of 1872; (2) minerals leasable under the Mineral Leasing kt of 1920; and (3) minerals salable under the Materials Act of 1947. Unlike valuable deposits of gold, silver, copper, iron, lead, etc., which may be locatable, industrial minerals are acquired through a variety of methods depending on use, composition, and date of acquisition. Table 1 may be used to establish the method of acquisition for most industrial minerals.

Jan 1, 1987

By D. C. Willett

INTRODUCTION The Symposium on the Development of Underground Space, held in Seattle, Washington, from October 1 through 3, 1980, was organized by the "Deep Space" subcommittee of the ASCE's Underground Research Technology Council. The primary objective of the symposium was the exploration of the interfaces between the investigation, design and construction of large underground facilities in "deep space" which, for the purposes of the committee, has been defined as starting at 100m below ground surface. The meeting focussed primarily on tunnels, caverns and shafts in hard rock; the meeting format comprised a number of brief presentations concerned with the technical aspects of investigation, design and construction, followed by an open discussion, and concluded with the assembly of recommendations regarding the interface problem by the symposium participants. The principal considerations brought out during the symposium, and a general review of the conclusions, are briefly presented in the following paragraphs. INVESTIGATION The sessions dealing with "Investigation" were chaired by Dr. H. Pratt. Presentations were made by Dr. D.C. Banks, Dr. W.A. Hustrulid and Dr. Pratt. The extent of the interface of the investigation phase with the other (design and construction) phases of an underground facility will depend in large measure upon the nature of the facility; at one end of the spectrum, the investigation must be in continuous and closely coupled relationship with the design of a radwaste facility. At the other end of the spectrum, for (say) a small mining operation, the interface is largely associated with the initial development, with only minor on-going involvement.

Jan 1, 1981

By J. J. K. Daemen, C. Fairhurst

Two aspects of tunnel support design are considered, and for both particular attention is paid to the influence of rock failure around the tunnel on the loads developed on the supports. 1) In general it has not been possible to extend analytical methods for the study of rock failure around tunnels to three dimensions. As a consequence it was not possible to calculate either the influence of the face or the actual sequence of support loading as the face advanced. The finite element method made this extension possible. A simplified analysis of the influence of the face and of the sequence of support installation has been made. The influence of the original stress field and of the rock behaviour on the length of tunnel which can be left unsupported (related to the stand-up time) is shown. The degree to which a 2-dimensional analysis can be used to approximate the final support load is shown to be dependent upon the post-failure behaviour of the rock. 2) Tunnel support design requires a knowledge of the forces and of the -rock displacements which cause stressing and deformation of the support system. A 2-dimensional model incorporating a detailed representation of several support systems, of the rock behaviour in the broken zone and of the interaction between rock and support is given. The model allows the calculation of the stress distribution in the support. The significance of the relative stiffness of support and rock on the stresses developed in the support is shown.

Jan 1, 1997

By John W. Rushton

THE PLANNED MAINTENANCE PROGRAM All concentrators should start with a planned maintenance program from day one. Every- body thinks they have a program in place before start-up, but in reality, most have only a fraction of what is needed to avoid the "Post Start-up Disaster" (PSD) - two years for start-up is not that uncommon. An effective program has all of the following: (1) Good people. (2) Area Maintenance. (3) Good PM Checklists. (4) Daily Work Schedules. (5) Written Work Orders. (6) Equipment Histories. (7) Backlog Control. The installation of a workable program takes hard work, talent, and commitment. You have to know what you are doing (hard work will not replace talent). Good People Good people are available in any location if you make the effort. Always check references carefully (both superiors, peers and subordinates). Was the last concentrator they worked at successful? Was it clean? Find out! Success or failure follows people around. I know people who are experts on PSD because they have lived through it three or four times. You need some college trained people with hands-on experience. There are no secrets, you have to make the effort. If you make a mistake in hiring (and you probably will), make the tough decision necessary to rectify it quickly. Area Maintenance Area maintenance refers to organization of supervision such that one person is uniquely accountable for every inch of ground and piece of equipment. Avoid overlapping authority if at all possible. You must have a planner as a staff position. A foreman cannot effectively plan and

Jan 1, 1986

By Robert D. Talvensaari

It is indeed an honor for White Pine, as a member of the copper mining industry, to participate in this Rapid Excavation Conference. Although our presentation, as the title indicates, is not a success story, we foresee, through our experience, future application of boring machines and rapid excavation equipment in the hard rock mining industry. One might ask what a copper mining company would be doing with boring machines and why the gamble on a high-cost, capital investment for a relatively untried application. Perhaps a little background on the White Pine mine and its geology will explain our daring and speculative motives. THE WHITE PINE MINE The White Pine Copper Company, a wholly-owned subsidiary of Copper Range Company, operates a mine, mill and smelter at White Pine, Michigan in the western Upper Peninsula approximately 6 miles due south of Lake Superior. We employ approximately 3,000 people from the surrounding area and mine approximately 25,500 tons of low grade (1%) copper ore per day. The orebody is contained within several distinct sedimentary horizons that comprise the lower 20 feet of a Precambrian formation known as the Nonesuch Shale. Numerous articles and reports have described many aspects of the White Pine operation and the geology. I will brief you only on that criteria which precipitated our interest in rapid excavation equipment and techniques, specifically, boring machines. Mineralogical and optical studies have demonstrated that the siltstones, sandstone and shale beds all contain relatively barren and discrete particles of quartz (25%), feldspar and mica, bonded with

Jan 1, 1974

By A. L. Mular

Optimization has been defined as the procedure of locating the best of something or the best way of doing something (Mular, 1971). Several texts (Himmelblau, 1972; Ray and Szekeley, 1973; Box and Draper, 1969; and Lee, Adams, and Gaines, 1968) on the subject are available. Such techniques have been placed in two categories, namely, off-line optimization and on-line optimization. For the former, an optimization model is employed; for the latter, a black box approach is involved. The essence of an optimization problem becomes obvious, when a response surface is considered. Suppose that a response (in this case, a criterion of improvement such as profit per day; grade of concentrate per day) denoted by Y, depends only on two variables, X1 and X2, which can be manipulated and controlled. The relationship between Y, X1 and X2 may be represented graphically as shown in Fig. 1. The diagram is called a response surface and its height, Y, is determined by X1 and X2. Points associated with equal responses constitute response contours. The shape is that of a hill, and optimization is the procedure of ascending the hill to reach the top (maximum). In practice, a response surface is subject to disturbances which distort its shape and shift its location from time to time, so that the exact location of a maximum is imprecise. Generally, constraints (restrictions of some sort) on responses and manipulable variables serve to define a region of permissible operation.

Jan 1, 1979

By M. Misra, I. Anazia

The effects of the enzyme, peroxidase, on the sedimentation and consolidation characteristics of Florida phosphate slimes were investigated. Results indicate that pretreatment with the enzyme was beneficial for slime dewatering and consolidation. Biological activity, resulting from slime pretreatment with the enzyme, induced higher mechanical binding between slime particles.

Jan 1, 1990

By William A. Dupree, Mark J. Schultz, William J. Francart

Maintaining intake escapeways clear of contaminants from mine fires has been an issue for many years. Removing fire sources from these entries reduces the risk of contamination greatly. In recent years, concerns have been raised related to contamination of the intake escapeways by leakage when fires occur in adjacent airways. This paper discusses measured leakage rates for multiple stoppings at various pressure drops across stopping lines in a number of actual coal mines. Also addressed are methods for reducing the contamination risks for the intake escapeways, considering the ventilation system employed. The Effects of Air Leakage The effects of air leakage through ventilation controls has been well documented. While normal leakage is expected through stoppings, overcasts and other structures, abnormally high leakage results in an inefficient ventilation system and can increase operational costs for a mine. In addition, excessive leakage results in less control over mine ventilation airsplits. This may compromise the isolation of mine escapeways, and allow adjacent entries to be rapidly contaminated by products of combustion in the event of a mine fire. A study was conducted at ten mines in which air pressure and quantity measurements were taken near the active sections. The method used to construct the ventilation controls to separate airways was also noted. Stopping Construction Table 1 shows the type of stopping construction commonly used in the 10 mines included in this study. Main entry stoppings were normally built with mortared joints (wet stacked) with sealant applied to the high pressure side of the stopping. In most cases the entire face of the stoppings were sealed. In one case only the joints between blocks were sealed but the perimeters were sealed in all cases. Some mines also sealed the low pressure side of the stopping. Solid blocks were normally used for main entry construction and hollow blocks were sometimes used for longwall panel development. [ ]

Jan 1, 1993

By B. T. Stanley

The basic geological data, derived from boreholes, exploratory test pits, drivages, and mine development, include information on parameters such as ore thicknesses, grades, depths below surface, structural attitudes of beds, rock types, and lithology of beds overlying and underlying the deposit. These data are usually supplemented by analytical information obtained from more detailed chemical, physical, and structural investigations of the various horizons. Even then, the relatively small number of sample points in the ore body and the sparsity of the sample volume make it necessary that the available information be interpolated between sample points and extrapolated into areas beyond the limits of the sample points. Such interpolation and extrapolation are usually done by making suitable assumptions about the parameter's continuity in the ore body and by building a suitable mathematical model. The mathematical model provides the values for chosen parameters at the nodes of superimposed conceptual grids of any desired dimensions such as a grid cell equal to the size of a mining block or any other criterion. This network of values, for any parameter, can then be used for mine planning, designing, and controlling functions. Additionally, these data can also be used to calculate ore reserve and quality in total and/or for any required block. Figs. 1 and 2 broadly illustrate the scope of work that may be involved in a geological ore-body modeling study for a coal deposit. Figs. 3 through 6 describe the scope of a commercially avail- able computerized system (MEDSYSTEM of MINTEC, Inc.) for creating drill-hole data base, mineral inventories, and for planning coal and uranium projects. The application of MEDSYSTEM to calculate reserves and to long-range planning in steeply pitching coal deposits is described in subsection 3.4, Chapter 4.

Jan 1, 1979

By Steven J. Schatzel, Mark M. Mazzella, Robert A. Kimutis, VASU GANGRADE, James D. Addis, Marcia L. Harris, Mayley Guitard

Researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated the impact of potential shale gas well breaches and subsequent gas inflow on selected mine ventilation systems of operating longwall panels using a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) and Sulfur hexafluoride (SF6) as a tracer gas. A series of tests were performed at 340, 400, and 500 cfm inflow levels utilizing different mine ventilation scenarios. Results suggest that the breached gas can be diluted to meet statutory levels when the longwall panel is adequately ventilated. The results enhance the understanding of the gas inflow and mine ventilation system interaction and provide critical information to the industry and regulatory agencies for improving miners’ safety.

Feb 1, 2024

By William J. Miles, Raymond E. Blair

The oil and gas drilling industry is the largest user of "functional" industrial minerals for well drilling and completion. (Functional industrial minerals can be defined as those used for performance characteristics rather than composition.) This industry's use of industrial minerals involves complex mining, processing, and distribution of products. The cost of these products at the well site reflects the complexity of distribution to typically remote locations and the cost of service. Table 1 illustrates the use of functional industrial minerals by the drilling industry. The total tonnage shown is almost 2 1/2 times larger than the 3.3 Mt (3.6 million st) of kaolin used by the paper industry for filling and coating, another major use for functional industrial minerals. Drilling fluids are an indispensible part of a drilling operation. These fluids perform several functions simultaneously. They cool and lubricate the drill bit, remove formation cuttings, increase the specific gravity of the fluid to counteract formation fluid pressures, provide a filter cake on the wall of the drill hole to prevent drilling fluid loss to the formation, protect the porosity of producing zones, and prevent reaction of the formation or formation fluids with the drilling mud. When porosity of a formation exceeds the ability of the drilling fluid to form a wall cake, it is referred to as lost circulation. Because these fluids are being constantly formulated for changing formation conditions, they require a skilled technician or drilling mud engineer on the site at all times. Drilling fluids are composed of oil or water as the liquid phase, and industrial mineral products and chemicals to control chemical and physical properties. The basic function of viscosity and suspension result from the use of gelling clays and chemical and mineral dispersants; specific gravity of the mud is adjusted with mineral weighting agents; filtration control is maintained by clays and various natural and synthetic polymers; platey minerals and scrap products are used for controlling lost circulation in porous or fractured zones; salts are added to the mud to inhibit shale and clay swelling; chemicals are added for pH adjustment, prevention of corrosion, and as scavengers for formation fluid components. Because of the clay component, drilling muds have rheological properties different from conventional fluids, behaving as Bingham plastic fluids as opposed to the Newtonian behavior of water and oil. Newtonian fluids will begin to flow with the application of any force, however small. Bingham plastic fluids require a finite force or shear stress (yield value) before flow begins. Thixotropy is another property of clay-based drilling fluids. At rest they form a gel structure that suspends the weighting agents and rock cuttings. These gels break down when a finite force is applied and circulation is restored. At the bit where shear rates are the greatest, the viscosity or resistance to flow decreases, so hydraulic pressures and pumping costs are minimized. A drilling rig provides a means of rotating a hollow pipe attached to a cutting bit. A mud pit or tank is used for mixing the drilling mud and its components. A centrifugal pump delivers this fluid to the drill ripe and down to the bit

Jan 10, 1983

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By S. Subramanian, K. A. Natarajan, D. N. Sathyanarayana

FTIR spectroscopy is used to study the ad¬sorption of an oxidized starch on hematite, corundum, and quart: substrates. The difference spectrum of the adsorbed starch on hematite indicates surface reactions involving -CH2OH and -COH groups and shows striking similarities with that of the ferric-starch system, suggesting chemical interaction between the iron of hematite and the starch adsorbate. The IR spectra of starch adsorbed on corundum and quart: show no evidence of chemical interaction, although hydrogen bonding is apparent. The extent of adsorption of starch on hematite. corundum, and quartz decreases along the series. The evidence for chemical interaction of starch with hematite is further obtained by the X-ray photoelectron spectra of starch adsorbed on hematite, showing noticeable decrease in peak positions of O(Is) and C(Is) of free starch. The Mössbauer spectrum of hematite with stanch adsorbed on it complements these findings.

Jan 1, 1990

By Ch. Arvanitidis

This paper presents the design solution for an actual case of settlement tanks, for a wastewater treatment plant under construction, actually founded on swelling clay (the nature of which had not been appreciated beforehand) and suffering considerable damage as a result. Two points of interest prompted the use of a numerical model as an alternative approach to the traditional method of analysis: First, the desire to compare the in situ measured deformation and displacement of the tanks with the figures calculated by the numerical model. Second the need to check the validity of the suggested solution as a remedy, i.e. the replacement of a certain thickness of clay by graded material.

Jan 1, 2005

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1998

By K. G. Sutterer, P. T. Wang, R. Sweigard

One possible alternative for the disposal of flue gas desulfurization (FGD) by-products is to use it as backfilling support material in highwall mine adits. The finite element method was used to analyze the variation in stresses and displacements within and around a highwall adit backfilled with FGD materials. The engineering properties of the rock material and the optimum mix of the FGD materials were obtained from laboratory tests. Finite element analyses show that, for the case in question, the roof displacement would decrease about 48% and the peak stress could be decreased by about 58%. The study indicates that fairly weak FGD materials can eventually lead to the stability of backfilled highwall adits.

Jan 1, 1998

By V. D. Ayurov, N. O. Kaledina

The coal mines monitoring should be based on the usage of simple and evident models, letting in the total unity to reflect a structure of organization of mine, system ability of its construction and specific character of its functioning. Such models are offered to create on the basis of extracted hierarchies of objects of mine. All objects of mine are broken on levels of technological hierarchy. For objects of each level of hierarchy there are made balanced models of entering and leaving material flows. Then these balanced models are coordinated among themselves by the help of the inter hierarchical relations. So the structured-qualitative characteristic of the object of monitoring, reflecting in a kind of the table structure of formation of material flows on mine, their intensity and measure of transformation is formed under transition from one level of hierarchy of mine to another. An example of real us- age of hierarchical balanced models on mine is given. The mathematical models of coal mine monitoring should reflect objective laws of their structural organization and functioning. Therefore under the constructing of mathematical models it is important such a way to reflect a structure of the mine organization, that in totality the models has been reproduction of system ability of its construction. The knowledge of the separate parties of functioning of mine, reflected in particular mathematical models, should "to be packed" in combined unity. Or else, they should be connected in system, convenient for recognition by the person. Considering the mine, the expert allocates multi-dimensionality of the objects of making its elements. He always has the knowledge of laws of development of mining work that is connected with pithy stratification of researched object. In dependence of sparial-temporary level of abstracting there are allocated the horizon, wing of a mine field, layer, panel, extracting face, longwall in coal mine. The human thinking on each of these levels operates with a set of concepts peculiar to him, characteristics, definitions.

Jan 1, 1996