Search Documents

By M. K. Gangal, E. D. Dainty

CANMET/MRL has been contributing to an industry/government program to assess the quality of air in mines, and improve the working environment for Canadian miners. The ultimate aim of this program is to recommend a sampling methodology and appropriate concentration limits for both the soot (diesel particulate matter - DPM) generated by diesel equipment, and respirable combustible dust (RCD) as measured underground. The program was conceived by the Canadian Adhoc Diesel Committee, which consists of representatives from seven major Canadian mining companies, three provincial inspectorates, one union representative, two manufacturers of diesel equipment, and CANMET, a Federal Canadian research agency. This paper describes the modification and laboratory confirmation of an existing methodology for the sampling and analysis of DPM/RCD, including: sampling problems, filter selection, filter efficiency, DPM size distribution, the approximate performance of fractionating devices, and it reports the results of current ambient measurements of exposure levels in Canadian underground mines. Because of the concern about the health impact of DPM/RCD on mine workers, North American agencies are in the process of establishing limits for these aerosols. So far, the Province of British Columbia is the only jurisdiction in North America to legislate the maximum exposure level of RCD in its underground mines, i.e. 1.5 mg/m3 interim level recommended by the Adhoc Diesel Committee. It has also recommended the use of the CANMET/ADHOC RCD sampling protocol.

Jan 1, 1993

By Carl R. Peterson, John Herrick

INTRODUCTION The need for substantial advances in underground excavation technology has produced considerable research activity on a wide variety of concepts under a variety of Government funded programs. One goal of this "Rapid Excavation" effort has been the development of a means to apply the well-known virtues, both technical and economic, of the drill and blast method in a continuous process. The spiral blast concept, aimed at this specific goal, has been funded for initial studies (1) by the ARPA Rapid Excavation Program and, for the experimental work reported herein, by the Department of Transportation (2). The economy enjoyed by the drill and blast method stems from two factors: explosive energy is relatively cheap; and this energy is released so as to cause rock fragmentation largely through tensile failures. The relative ease and efficiency of tensile rock failures have long been recognized. The drill and blast process of course cannot be truly continuous since drilling and blasting (and other necessary functions) simply are separate, distinct operations. Although some surface explosive work has been done to avoid the need for drilled blast holes (3) it does appear that the high performance associated with explosive excavation requires placement of the explosive beneath the rock surface. This paper describes studies of blasting pattern which, in simplest terms, replaces the occasional heavy blast of conventional practice with frequent, much smaller blasts. The objective, of course, is to reduce the size of individual blasts

Jan 1, 1974

By D. A. Bulled

• "What does it look like?" - describes the appearance. • "How does it work?" - outlines the operation. e "Why does it work?"- explains the principles. • "What about controls?" - indicates possible automatic systems. • "How is it sized?" - discusses the necessary testwork and evaluation. • "What are the results?" - demonstrates test and operating results. • "What's the benefit?" - concludes with gains for the user.

Jan 1, 1999

By William L. Hodgson

HOARDS was written to fill the needs of an active minerals explorer. It permits retrievals using a number of spatial functions as well as direct relational logic, and enables statistical analysis within the system. Specified for use by non-EDP oriented staff, HOARDS also offers functions to subset, transform points to polygons of influence, and to calculate polygon overlap, enabling ready and efficient conversion of databases containing point oriented sample data to area/volume mine planning format. Both the design and implementation to date, and proposed enhancements are discussed.

Jan 1, 1979

By Carolyn S. Watkins, Thomas E. Ward, Debby F. Bruhn, Vern Winston, Mary Lou Rowland, Deborah K. Bulmer

The genetic characteristics of members of the genus Acidiphilium are poorly understood. As part of our study of the genetics of these bacteria, a search was made for an endogenous bacteriophage. Such a bacteriophage has been discovered. Several properties of the phage have been investigated. The phage has a lambdoid morphology and is somewhat larger than lambda. A variety of factors which affect phage stability have been investigated. The bacteriophage infects several of the strains that have been tested. Study of this bacteriophage should greatly increase our understanding of genetic mechanisms in Acidiphilium.

Jan 1, 1989

By M. R. Bowie, J. M. Barker, J. S. Hingtgen

Techniques of testing perlite require a combination of art and science. The modifications made to the perlite Corp. vertical laboratory furnace include addition of instrumentation, flowmeters, vibrators, automatic feeders, and regulators. The basic testing sequence consists of expanded density, furnace yield, compacted density, percent sinkers, and compaction resistance. These tests are modified versions of those specified by the Perlite Institute. This sequence is designed as a preliminary evaluation of a material's suitability for horticultural-aggregate end uses rather than a detailed measure of filtration capability.

Jan 1, 1988

By R. D. Williams

INTRODUCTION In a very real sense, Butte, Montana is where the copper came from that won two world wars. The price for that unrestricted mining and smelting of copper came due in 1983 when Butte was declared a Superfund site. One of the most complex remnants of this mining history is the Parrot Tailings site. The Parrot Smelter operated from 1881 to 1910 moving Upper Silver Bow Creek to the south and depositing approximately 370,000 cubic yards of waste material adjacent to Upper Silver Bow Creek. Additional mixed waste from other processing sites deposited below the Parrot Tailings at the Northside Tailings, Diggings East and Blacktail Creek Berm total approximately 224,000 cubic yards of contaminated material. As part of the Superfund remedy, EPA proposed leaving all these wastes in place. This proposal prompted a detailed criticism by several geoscientists familiar with the site. The EPA’s 2006 Record of Decision (ROD) did in fact leave these wastes in place which set the stage for a series of studies which continue to refine how best to protect extensive completed Superfund Remediation downstream of Upper Silver Bow Creek. HISTORY OF THE PARROTT MINE AND TAILINGS Placer gold was discovered in Silver Bow Creek, the headwaters of the Clark Fork River only a few miles from the Continental Divide in 1864. This discovery lead to a stampede of placer and lode claims. One of the first lode claims located was the “Parrot” lode, located in the fall of 1864. Progress for developing a mine at the Parrott was slow and it wasn’t until 1876 that one of the original locators encountered a rich vein of chalcocite. Butte had its first copper mine! The Parrott mine was patented in 1879 and by 1881 the Parrot, having lost a “t”, concentrator and smelter were built. The smelter and concentrator were an immediate success with a considerable market for processing the District’s rich copper ore. In 1885 the employees of the Parrot Smelter bought the Butte Reduction Works, another smelter. In 1885 dams were built on Silver Bow Creek to contain various tailings and related processing byproducts (Figure 1).

Jan 1, 2019

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By Y. Nakahiro, T. Wakamatsu, M. S. Elsalmawy

The flotation of quartz, feldspar and alumina was studied as a function of pH when using N-alkyldiamines as collectors. The lengths of alkyl chains of diamines were 8, 9, 10, and 12 carbon atoms. It was found that shorter hydrocarbon chain length of alkyldiamines has stronger tendency to float quartz while the feldspar responded poorly to flotation with these collectors at high pH values. The effect of addition of nonionic surfactant of Brij type, when using dodecadiamine as collector, was investigated. Flotation studies in the absence and in the presence of sodium dodecylsulfonate were carried out. These studies have indicated that sodium dodecylsulfonate, in the concentration studied, functions as strong depressant for feldspar.

Jan 1, 1995

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous because of their fatality records. However, statistical analysis of West Virginia safety and production data from 1993 indicated that, when considering the correlation between accident severity and tons mined per employee-hour worked, the most efficient mines were, with the exception of very small mines, not the safest operations. This paper presents the results of an extended analysis of West Virginia mine safety using 1993 and 1996 data and concludes with the method used to suggest current priorities for focusing interventions.

Jan 1, 2000

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By D. Craig Camp

Microtunneling has successfully completed both horizontal and vertical curves. This paper covers the historical development of curved microtunneling and a description of one microtunneling project. The completed microtunnel is used for electrical transmission in Japan. The crossing had several concerns including right of way, social disruption, obstructions, the cost of intermediate shafts, and political restrains. In order for this drive to meet all of the imposed restrictions, four horizontal curves and one vertical curve were planned and executed in accordance with the design. Iseki Poly-Tech of Tokyo, Japan designed and built the microtunneling machine to meet the project requirements. Curved microtunneling has been successfully used on fourteen projects in Japan. The reason for a curve has been that the project could not be rerouted, short straight drives could not be used to negotiate the curve, or the project’s social and environmental conditions required a curved tunnel. The following table (Table 1) includes summary information on 14 curved microtunnling projects that have been successfully completed in Japan. The first column is a reference number. Columns two through four include basic project information. The fifth column is the total project distance completed by microtunneling. The sixth column is the project’s microtunneling duration. The seventh column is the machine type and size. All of the machines listed are manufactured by Iseki Poly-Tech of Tokyo, Japan. The size is the internal concrete pipe diameter; all of the projects listed were completed with Japanese standard concrete pipe. The eighth column contains a general description of the soil. The soil type and blow counts are approximately equal to ASTM D 2487 standards. The ninth column lists the radius of the curve and the span distance or the distance microtunneled that included the curve. The radius of a vertical curve is denoted with a “VR”, a span with both a left and right hand curve is denoted with a “S”. Other significant first events are also noted in this column. The first curved microtunneling project was completed in 1982 using a conventional microtunneling machine with standard Japanese concrete pipe and a very long radius curve while maintaining grade for the gravity sewer. The second curved microtunneling project included multiple radii curves, all in the same direction, on a single drive. In 1989, on the fifth curved microtunneling project, a “S” curve was successfully negotiated. On the seventh curved microtunneling project, completed in1995, a tight radius curve was negotiated. In 1996, the eighth project included a vertical curve. The thirteenth curved microtunneling project, completed in 1997, was the first project to utilize a microtunneling machine specifically designed to negotiate curves. The fourteenth curved microtunneling project was the accumulation of all

Jan 1, 2001

By Edward Burris, Terry Gorsuch, Joseph M. Hans

INTRODUCTION In any large earth-moving operation, good planning and management are necessary to complete the operational tasks promptly and successfully. When an earth moving operation is complicated by radioactive contaminants, normal earth moving techniques and procedures must be modified. Any planning and management, therefore, must include the radiological aspects of the operation. It was found that the radiological aspects dominated most of the planning and management activities and were extended to all facets of the decontamination work at the former Shiprock uranium millsite. These planning aspects are discussed and their use to develop a work plan is described. The management aspects are discussed and their use to establish a management structure are also presented. PLANNING Some method of procedure, formulated beforehand, was necessary to govern the decontamination work at the former Shiprock uranium millsite. This procedure was expressed in the form of a work plan which served several listed purposes. 1. It defined the work to be done and the sequence it would follow. 2. It was used as a yardstick to measure progress. 3. It was used to assign organizational responsibilities. Several factors were considered to aid in the development of the plan. These factors are discussed below: Goals It was established that radiation exposure was occurring to persons working at the millsite, and in an around the community of Shiprock, from airborne radioactive mill wastes and radon-222 exhaling from the tailings piles. The goal set for the decontamination work was to reduce on-site exposures to levels acceptable for the millsite occupants. The attainment of this goal would also have a substantial impact in reducing off-site exposures. The objectives necessary to achieve the goal were consolidation and containment of the wastes. The former objective implies decontamination of the millsite and environs, and the later implies stabilization of the wastes. In practice, a total and complete decontamination of the millsite and contaminated environs would be very difficult and costly. The costs for decontaminating them could be high enough that an alternative method might be more cost-effective for reducing human exposures (i.e, move the affected people away from the source). The interim guide "Radiological Criteria for the Decontamination of Inactive Uranium Millsites" was used for the decontamination criteria (EPA 74). Briefly, the criteria state that off-pile decontamination should be effective enough to reduce the net above ground exposure rate to less than 10 [u]R/hr for unrestricted use of the affected area. When decontamination cannot readily be achieved, the exposure rate levels could be relaxed to 40 [u]R/hr; however, the affected area has to be restricted. The second objective, waste containment, means isolating the wastes from the biosphere. Since no method of containment was available at the beginning of the millsite decontamination effort, temporary containment (interim stabilzation) became the objective. The tailings pile and decontamination wastes would be covered with clean fill. The interim stabilization should last from 5 to 10 years until the final disposition of the wastes will occur. The goal, therefore, would be achieved by decontaminating the off-pile areas to less than 10 uR/hr where practical. The decontamination wastes would be used to plate the surface of the tailings pile and would be covered with clean fill. Radiological Survey The radiologial survey is the key factor for planning a decontamination activity. The survey should delineate the spread and depth of the contaminants relative to the decontamination criteria. Surface wastes, in general, can be evaluated for spread and depth with reasonable radiation survey equipment. Subsurface wastes on the other hand can be missed entirely, as happened during the radiation survey at the Shiprock site, although numerous exploration holes were bored and dug. The survey results can be used to define areas that may not be amenable to decontamination because of complications or safety reasons. For example, no decontamination of the bluff base was to be attempted because of the possibility the bluff might collapse on the personnel and equipment. Contaminated bottoms of decant ponds on the flood plain were not removed because they would be slurried by ground water. Slurry removal was deemed inefficient because the contaminants would be scattered and no equipment was available for its transport. In summary, the radiological survey defines the boundaries of the decontamination work and provides

Jan 1, 1981

By Kent G. Homewood

The well-being of any company is directly related to the well-being of its employees and to the effectiveness with which the personnel resource is managed. In an era when personnel management has steadily become more complex, there is an increased awareness of employee information systems at all levels of management due to: (1) regulations enacted by federal, state, and local government agencies; (2) technological advances within the mining industry which have resulted in the requirement for highly skilled personnel; (3) increasing concern for the confidentiality of employee information; and (4) management's need for information for planning purposes to control costs and for early recognition of trends and potential problems. In the past it was sufficient to maintain records manually. Today computers are necessary to provide information on short notice and effectively manipulate large volumes of' data. This discussion will describe the following aspects of employee information systems: (1) collection and maintenance of information, and (2) applications which include employee health, salary administration, management re- sources, and labor negotiations.

Jan 1, 1979

By R. V. Ramani, S. Tan

In this paper, several commonly used computer truck-dispatching criteria are evaluated. A computer-oriented truck-dispatching and production simulator was developed to provide data for comprehensive cross comparison among the dispatching criteria. The definitions, primary considerations, characteristics and performances of these dispatching criteria were investigated. From the simulation results, it was concluded that, in general, no one criterion can dominate all others. However, several dispatching criteria that have good potential to increase performance can be identified. All basic dispatching criteria, including minimizing truck waiting time, waiting shovel with minimum waiting time, minimizing truck saturation, maximizing truck momentary productivity or optimization of truck routes, provide local optimal solutions. To obtain a direct global optimization solution for this complex stochastic process does not appear to be likely Therefore, the search for an optimal dispatching criterion that will fit all conditions may not be realistic. It may be necessary to search for a hybrid combination of the several truck dispatching criteria that have good potential for a given situation. An approach to selecting such a hybrid dispatching criterion is presented.

Jan 1, 1993

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By Vernon R. Degner

The past two decades has seen the application of the mechanical flotation machine, originally developed primarily for metal1iferous ore beneficiation, increasingly applied to cleaning coal in the 28x0 T. Mesh size range. Internal cell hydrodynamic studies of mechanical flotation machines of all sizes, as well as computer aided modeling studies of flotation kinetics has, within the last five years, established a basis for optimizing coal flotation circuit design and machine operation, and has a1 so pointed a way toward improvements in mechanical flotation machine design for the future. Consideration of the trend toward increased fines produced by current mining techniques, as well as the environmental need for a progressively cleaner product, lends support to basing the design of the mechanical coal flotation machine of the future on finer feed; below 100 microns in size. Future types of mechanical flotation machines, which may satisfy the fine coal cleaning requirements for a significant improvement in product grade while maintaining the combustible recovery levels of current technology, are discussed.

Jan 1, 1988

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By Zhu Mingshan, Wu Jiang, Xu Yingqin

A mathematical model to simulate spontaneous combustion of coal in goaf was developed. Under the condition of two-dimensional flaw of air through a bed of uniform mixture of coal, gob, stone etc., the model simulates the temperature rise in the air-and-particle system associated with Arrhenius particle surface reaction. The model is developed as a set of coupled non-linear partial differential equations, which include (1)mass conservation equation for oxygen, (2)energy conservation equation for gas, (3)energy conservation for solid, and (4)velocity equation for gas, that are solved numerically. An elaborate parametric analysis is made of effect of leakage air flux and position of source and sink, parameters relating to the coal accumulating character and the kinetic properties of coal on the tendency to spontaneously combust. In addition, the dynamic process of temperature rise within goaf under several conditions is displayed with picture drawn by computer.

Jan 1, 1991