Search Documents

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By John W. Lane

Climax Molybdenum Company, a Division of American Metals Climax, Inc., operated a hydrometallurgical plant* at Climax, Colorado from August 1966 through August 1968 to recover molybdenum from a mixed oxide and sulfide ore. The ore treated for this addition to the existing plant contained sufficient Molybdenite values to be mined for Molybdenite recovery alone, so that the oxidized molybdenum recovery could be regarded as a byproduct operation. Climax is located at an elevation of 11,300 feet. All process equipment, except thickeners, was enclosed in buildings. Annual snowfall is approximately 250 inches per year. Paved highways and rail service to the plant are maintained and kept open all year. Most of the employees live in the town of Leadville, which is approximately twelve miles from the plant site. The sulfide flotation plant handles 40,000 to 45,000 tons per day of ore. The mine is one of the world's largest underground mines.

Jan 1, 1971

By Richard L. Ash

Less than optimum production in mining always results when poorly blasted material is provided at loading points. More often than not the cause is due to blasting founds that fail to fully control and utilize explosive energy. In many cases the problem exists because too few blasters understand how blastholes actually break rock and recognize that blasting is a three-dimensional process in designing their blasts. To better understand how blasts can be more effectively designed the two major rock breakage processes are described. In addition, the respective contributions of the borehole and detonation pressures are defined as are the specific roles of the several important blasting design variables. The concept of stiffness as an engineering principle and its significance in blasting design is introduced for explaining the breakup of rock. Basic guidelines for affecting control over fragmentation and side effects like over-break are offered.

Jan 1, 1975

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and surficial evaporite brine. Those advantageously located now supply world markets. Materials of similar grades and magnitude, but less favorably located, will come into production as present sources are depleted and markets expand. Some of these potential supplies have been explored, and are reserves in the sense of known availability and quality. Reserves herein are of two classes, those proved by close drilling and assaying, and those of only probable status because their scale and grade are unsystematically indicated. Possible resources include similar materials whose bulk can only be inferred on indirect evidence. All figures apply to total materials in the ground. No allowance is made for losses in mining, evaporation, beneficiation, or chemical processing.

Jan 1, 1977

By M. U. Khan

"Underground mine diesel equipment generally offers more flexibility as compared to electric powered systems. Diesel exhaust is an adverse agent which affects the health of underground miners. The National Institute of Occupational Safety and Health (NIOSH) regard diesel exhaust as carcinogenic. The NIOSH 5040 method is an established technique for measuring Diesel Particulate Matter (DPM). This process inherently involve a lag time before an accurate exposure determination can be made during which miners are potentially overexposed to DPM. This issue can be addressed by using realtime DPM monitors. This paper presents underground mine shift average based and realtime monitored DPM values monitored in US mines. A FLIR Airtec instrument has been used for realtime measurement whereas shift average based DPM has been determined by the use of NIOSH 5040 method. A log of diesel equipment movement was kept. DPM concentrations versus time were plotted and analyzed. High DPM sources were identified and the FLIR Airtec was demonstrated to be satisfactory for realtime DPM measurements. INTRODUCTION The use of diesel equipment in mines is an attractive option due to its ability to convert a large fraction of available energy into useable work. Diesel engines are rugged, dependable and fuel efficient. It is very common for diesel engines in heavy duty trucks to have a life of 1,600,000 km [Anon, 1999]. Generally in underground mines compared to electric powered equipment, diesel equipment provides more maneuverability. It can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment keeping in mind the recent developments in other energy alternatives [Anon, 2001a]. A harmful aspect to the use of diesel as a fuel is its resultant emission as an adverse environmental exposure agent. Generally diesel particles are approximately one order of magnitude smaller than respirable dust aerosols in underground mines (typically less than one micron in size) [Kittelson, 1998]. Force of gravity has less effect on DPM due to its small particle size. The phenomenon of less gravitational attraction increases the settling and residence time of DPM in the mine atmosphere. High residence time of DPM as compared to other mechanically generated particles increases the chances of diesel particles deposition in the human respiratory tract. The small sized diesel aerosols penetrate deeply into regions of the human lung [Morawska. et al. 2005], which increase the health risks associated with long term exposure to diesel aerosols. Published studies documented the adverse health effects of DPM exposure [Walsh M.P., 1999]. Continuous and long term DPM exposure can result in respiratory disease, lung cancer, reduced lung capacity, and heart disease. NIOSH has declared that the reductions in DPM exposure would reduce cancer risks. In underground mines DPM determination is a challenging task and it is becoming a matter of serious concern due to the harmful health effects associated with the exposure of DPM. The current study involves the determination of realtime and shift averaged based DPM in underground mines of United States of America (USA). Realtime DPM was measured using FLIR Airtec monitors and shift averaged based measurement was performed by the MSHA approved NIOSH 5040 method. FLIR Airtec uses laser scattering approach to measures the Elemental Carbon (EC) component of the DPM. The results from the FLIR Airtec were compared with the results of NIOSH 5040 method and its performance was found satisfactory."

Jan 1, 2015

By Johan Bosch, Wout Broere, Minh Ngan Vu

"INTRODUCTION Shield tunnelling is often used in constructing underground infrastructure in cities due to the ability to limit settlements and damage to existing buildings. However, in an urban environment with soft overburden and buildings on pile foundations such as the North-South Line project in Amsterdam, there is a tendency to design the tunnel well below the surface and below the pile tip level in order to reduce interaction between tunnelling process and piles. This results in deep tunnels and deep station boxes. When the tunnels are located close to the surface and above the pile tip level, this would reduce the required depth of the station boxes and the construction cost. Moreover, other benefits of shallow tunnels are the low operational cost in the long-term and shorter traveling time from the surface to the platforms. Still, the tunnels should be constructed in such a manner that existing buildings are not structurally damaged, which results in a minimum required distance between tunnelling process and existing buildings. In this paper, the extent of the area that is influenced by tunnelling will be investigated in order to determine the limit distance from tunnelling to existing foundations without inducing too large building deformation. From analysing empirical data of many shield tunnels, Peck (1969) firstly presented the settlement trough on the surface induced by tunnelling in soft soil as a Gaussian distribution. This is also confirmed by other authors (Cording and Hansmire, 1975; Mair et al., 1993; Ahmed and Iskander, 2010). In this study, the Gaussian curve is used to investigate the ground movement when tunnelling in order to find the effects on existing structures. Based on the results from centrifuge test and empirical data, Mair et al. (1993) showed that the subsurface settlement profile distributes as the Gaussian curve also. The width of settlement trough at the depth z depends on the depth of the tunnel z0 and a coefficient K depending on depth. Other studies by Moh et al. (1996), Grant and Taylor (2000) and Jacobsz (2003) based on Mair et al. (1993) proposed a limited change of K in various kinds of soil."

Jan 1, 2016

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By Henry H. Rubin

Rubber and its contributions to the economic solutions of environmental problems in the minerals industry. The intelligent applications of "Rubber" to systems of noise abatement, vibration isolation, dust containment, weak and corrosion resistance has proven economically beneficial. Intelligent application requires a thorough understanding of the nature of the material, knowledge of the process wherein it is going to be applied, and consideration of the environmental conditions in which it will serve, for these determine the proper amount, type, compound and configuration for an economically successful application.

Jan 1, 1979

By Silvia Misk, Cristina Araújo, João Felipe Costa, Roberto Rolo

Linear estimation methods are widely used for resource evaluation. Among the existing linear estimation methods, ordinary Kriging (OK) was accepted as the best estimator to determine the average ore grade of each block. However, OK is inadequate for modeling small blocks in relation to data spacing, resulting in over-smoothed models. In this study, the results of the recoverable resource from the short-term model are compared to estimated models generated by the traditional method, i.e., OK, and non-linear methods. The conclusion is that non-linear methods improve the accuracy and precision of the long-term model when compared to the model generated by OK.

Jun 25, 2023

By G. France

The Blair Athol Coal Mine (BAC) is a large open cut operation in the Bowen Basin of Queensland, Australia. Current mine capacity is about 11 million tonnes per annum (Mtpa) of export coal. On-line analysis at BAC consists of two Coalscan 9500s installed directly on the output of the crusher plant and immediately before the product stockpiles, while a third Coalscan 9500 is installed on the transfer conveyor feeding the train loading bin. The two product Coals cans have a dual purpose. The first is to provide real time coal quality data directly back to the mining operations. The second is that of modeling the product stockpile with accurate on-line information. This modeling enables both production and coal quality personnel to accurately examine the coal quality of each stockpile with a degree of resolution which previously had never been achieved.

Jan 1, 1999

By C. S. Boland

The Copper Range Company's mining properties are located in the Upper Penisula of Michigan. (Fig.). Early work indicated the presence of copper ore in a bedded deposit, confined to the base of the Upper Keweenawan Nonesuch shale, and exploitation of this deposit on a portion of the Company's property was undertaken by White Pine Copper Company. Diamond drilling of the White Pine orebody indicated that a major fault pattern terminated the values to the South-west. Further drilling Southwest of the fault zone proved a downward displacement of the ore bearing horizon some 1,500 feet and a lateral displacement of approximately 4,000 feet; and in this area an ore deposit was outlined in a large asymmetrical syncline locally plunging to the South-west. (Figs. 2 and 3)

Jan 1, 1962

By S. E. Knalafalla

The availability of a fluid whose gross behavior sharply changes in a magnetic field without affecting its rheologic characteristics has been recently demonstrated. A colloidal solution of a ferrimagnetic material, such as magnetite, in a liquid that is immiscible with and lighter than water is projected for use in selective separation of particles according to their density spectrum in a continuous fashion. Magnetic levitation forces were created as an antigravity field when the fluid was properly placed in an inhomogeneous magnetic field. Five spherical non¬magnetic objects with densities ranging from 2.70 to 11.35 gram cm ' were made to float or submerge at will in a 0.96-gram cm-3 density fluid placed at vertical magnetic field gradients ranging from 0.2 to I kilooersted cm-1. The magnetic levitation farce in dyne cm-3 was found to vary linearly as a function of the object-fluid density mismatch with a slope equal to one g, the acceleration due to gravity.

Jan 1, 1972

By Ben H. Daud

The systems optimization approach to mine planning has led to the adoption of a number of mathematical and computer models for short, medium and long range planning of mining operations. In the realm of open pit mine planning, the most common uses of such an approach have been in the areas of optimal pit design and planning of materials handling operations. Since a truck-shovel combination is the most widely used method of materials handling in open pit mines, a number of models have been presented in the past to analyze and optimize such systems. Broadly, these models can be divided into two categories. The simulation model, which is primarily used as an aid in analyzing the performance of either an operating or a proposed haulage system under the influence of externally alterable parameters, and the linear or integer model which is used as a tool for short or medium term optimization of the system under the operating constraints. In the first part of this paper, a brief discussion is presented of the linear/integer optimization models presented in the past, and in the second part a new model is described which is actually a combination of the simulation and the integer programming models. In its bare essentials, the model consists of an integer optimization algorithm, but the constraints are regularly and dynamically updated by incorporating the conclusions drawn from a stochastic simulation model of the mine haulage system. Since the successive optimization is performed by the mine operator who manipulates the constraints to guide the model towards the optimum, the mystical black box approach is minimized and should help in adoption of the model by the mine personnel. Also, by combining the stochastic simulation model and the deterministic integer model, some of the advantages of each are acquired.

Jan 1, 1976

By R. R. Young

Prior to 1903, the world's supply of sulphur was primarily from surface deposits in Sicily. The discovery of the first salt dome sulphur deposit in 1867 and successful development of the Frasch process for recovering the sulphur resulted in a large part of this essential element being supplied from these mines since 1920. Although the basic process is the same today, engineering and technological developments have evolved to allow its application under many adverse conditions. These and other challenges for the industry in today's environment will be discussed in the paper.

Jan 1, 1979

The role of ZnSO4 in activation of sphalerite (ZnS) and deactivation of lead-activated sphalerite has been investigated. Adsorption of metallic ions at the solid-solution interface, electrokinetic results for sphalerite under different chemical conditions, and thermodynamic calculations were used to elucidate the mechanisms involved. It is shown that flotation response of sphalerite in absence of activators is rather weak and that adsorption of ethyl xanthate on the mineral mainly electrostatic in nature. Zinc sulfate is found to activate the mineral but only in a narrow acidic pH range. This is attributed to the increase of zeta potential as well as the possible increase in amount of negatively charged bulk precipitated zinc xanthate. Lead ions activate sphalerite in a wide pH range and the lead activated mineral assumes a flotation behavior similar to that of galena (PbS). However, addition of ZnSO4 depresses the lead-activated sphalerite by replacing lead ions at the mineral/solution interface.

Jan 1, 1999

By Robert Turner

Gold and silver processing techniques are some of the oldest in the mining industry. Gold mining of high grade veins and deposits has existed for centuries. However, only with the higher gold prices in recent years and heap leaching techniques have the low grade gold and silver deposits become feasible to mine and process economically. By mining and hauling 3,600,000 tons of ore per year at an average grade of 0.03 ounces/ton gold and 0.385 ounces/ton silver, the Zortman- Landusky operations became profitable in 1982. To maintain profitably, a stripping ratio of less than one ton of waste to one ton of ore, and mine run ore placed on the leach pads which will yield approximately seventy percent go1 d recovery.

Jan 1, 1984

By E. W. Geist

This paper is presented from the viewpoint of the mill operator and maintenance supervisor. Its purpose is to highlight the things that have been accomplished by the mill designers to lighten the load for the maintenance superintendent and to reduce the overall costs for the plant operator. The complexity of plant design, the civil and structural engineering problems encountered when the satisfactory maintenance layout is accomplished are appreciated, and the writer is fully aware of the complexities of these problems. However, it is not the purpose of this particular paper to dwell upon these problems, nor to emphasize or de-emphasize the problems of the civil, mechanical and electrical engineers. It is simply that the paper will attempt to review what these people have accomplished in spite of the many technical problems. This paper then is prepared with the operator and maintenance people?s viewpoint. What is their definition of design for maintenance? It is the writer's interpretation that the various design concepts which mean improved maintenance are such items as (I) maintenance areas, (2) laydown space for maintenance materials in specific maintenance jobs, (3) the inclusion of bridge cranes in the plant and specific design of the craneways to accomplish flexibilities for the cranes, and (4) the location of the piece of equipment to allow maintenance people to work around the equipment - - - this specifically includes the orientation of the particular piece of equipment.

Jan 1, 1967

By Bo Arvidson

SALA MAGNETICS, INC. is now operating a 15 tph continuous high gradient magnetic separator, the SALA-HGMS® Mark III Carousel, as part of a complete mineral processing pilot plant installed at Sala's Cambridge headquarters. The Mark III can generate a maximum magnetic field of 18 kG making it possible to process even weakly magnetic, finely ground ores and ore tailings on a continuous basis at the performance level achieved in Sala's cyclic high gradient magnetic separators. Test results on iron ores, clay, and decoppering of molybdenum concentrate will be discussed. Bench scale tests have been performed on all of these materials using the SALA-HGMS® Model 10-15-20 Cyclic Magnetic Separator. A direct correlation may be made between cyclic and carousel results. Sala's Mark III Carousel high gradient magnetic separator is designed to permit scale-up to machines capable of processing two hundred (200) tons of ore per hour and more.

Jan 1, 1976

By Victor Phillips

The Humphrey Preparation Plant of Christopher Coal Company, located in Monongalia County, West Virginia, was built to process the combined production of the Pursglove No. 15 and the Humphrey No. 7 Mines. Both Mines operate in the Pittsburgh Seam, primarily producing Metallurgical Fuel destined for by-product ovens in the Pittsburgh District. The results of an extensive core-drilling program have established sufficient reserves of low-sulfur coal to justify a 20,000 ton-per-day preparation plant, This is the story of the preparation phase of this combined operation. Christopher Coal Company operated the Pursglove No. 15 Mine to produce steam coal, which was prepared in a conven-

Jan 1, 1958

By Jon J. Kellar

The adsorption of oleate at the surface of a fluorite single-crystal internal reflection element has been investigated using Fourier transform infra-red/internal reflection spectroscopy (FTIR/IRS). The application of this innovative experimental technique has added a new dimension to the investigation and understanding of collector adsorption phenomena. It is now possible, for the first time, to measure in-situ and in real time the adsorption density and bonding nature of collector species adsorbed at mineral surfaces. In this regard, oleate adsorption densities were calculated from spectral data, and the equilibrium adsorption isotherms were found to agree quite well with other adsorption isotherms reported in the literature. At low equilibrium oleate concentrations(<10-5 M), monolayer-type cover-age was observed in the chemisorbed region. It was found that in this region the adsorption density increases with an increase in temperature, which sup-ports experimental results from previous ex-situ FTIR studies and thermochemical studies in which it was shown that the chemisorption reaction was endothermic. At higher equilibrium oleate concentrations (>10-5 M), the adsorption density increases dramatically at the point of surface precipitation. The oleate adsorbed in the chemisorbed region has a distinctly different spectrum than the oleate adsorbed in the surface precipitation region of the adsorption isotherm. In the chemisorbed region, the oleate appears to be mono-coordinated at the fluorite surface.

Jan 1, 1989