Search Documents

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By A Weber, L MacNamara, H Schreiber

Design and development of the world?s largest flotation cell was completed in 2002. This was the first 257 m3 flotation cell installed in the mineral industry and represents a major development in the design of larger flotation cells. This cell has a 50% increase in volume over the widely installed 160 m3 WEMCO® Smartcell? flotation machine. In the next few years it is anticipated that 257 m3 flotation cells will be incorporated into rougher-scavenger flotation circuits in many more world class copper sulphide concentrators. The prototype 257 m3 cell, No.250 Smartcell? flotation machine was installed at Minera Los Pelambres in the front of Row 1 in the existing rougher flotation circuit. This cell is followed by nine No. 130 Smartcell? flotation cells. After the successful development phase, this unit has been incorporated as part of a row of No. 250 Smartcell? flotation machines at Minera Los Pelambres. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No. 250 flotation cell, and present a case study of the in-plant equipment testing. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulphide concentrator.

Jan 1, 2007

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

By L. Jurca, C. Gligor

After 1990, a great process of re-organisation and economic reform has occurred in the Romanian mining sector and especially in the pitcoal mining in the Jiu Valley. This process has included both legislation and the main aspects for getting an economic efficiency in the environment issues and for dealing the problems with social impact. Accordingly, starting with the year 1993 a new mining method has been introduced to turn efficient the pitcoal mining, and we speak about mining with caved in bed. This method has two variants: - with transverse strips and caved in bed; - with long face and caved in bed. Each of the above-mentioned variants has in turn several subdivisions, depending on how the longwall is prepared and on other characteristics. By using this method, the output has increased compared to other mining methods. The main safety aspects concerning caved in mining refer to: - great emissions of methane; - technical aspects (a mining method system, supports, discharging process); - pressure driving (analysed for the case of mining with long face, with transverse strips as well for the case of transverse strips when mining a subsequent sublevel).

Jan 1, 2003

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By A. K. Das, S. Pathak, C. Bhanu, P. K. Tripathy

Ferroalloys are integral part of steel melting process. The purpose of using ferroalloys is three fold e.g. killing of steel, modifying the slag composition and steel alloying. Amount of ferroalloys used for alloying is subject to requirements of steel properties e.g. yield strength, ductility, formability etc. Variety of ferroalloys (some-times pure metal) is used by steel industries depending upon their techno-economic feasibility. Size, chemistry and modes of addition of ferroalloys are suitably engineered to bring in operational consistency and cost benefits. Of late, Tata Steel has tried out a few ferroalloys for the first time with interesting results to meet the specific requirements of high strength interstitial free (IF) and micro-alloyed steels. Some of these ferroalloys have been put into regular use with complete or partial replacement of ferroalloys used earlier. Size of one of the ferroalloys has also been modified without any other adverse effects. This paper summarizes requirements of ferroalloys for the steel industry with special emphasis on recent trials.

Jan 1, 2007

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Immediate Past President J.R. Dixon Junior S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2000

By C. Musingwini, A. S. Nhleko

"Since the Global Financial Crisis (GFC) in mid-2008, capital has been more difficult to access. Mining projects must contend with projects from other industries for scarce capital. A decision to invest available capital in mineral projects requires that valuation be conducted to assess the expected return on the projects. The discounted cash flow (DCF) analysis is generally applied for the valuation of mining projects, whereby future cash flows are discounted to present value using an appropriate discount rate. The discount rate significantly affects the outcome of a valuation. Economic and finance theory provides tools to calculate discount rates. The discount rate must account for factors such as the risk and stage of development of the mineral project; hence the appropriate discount rate to utilize in a project is often a subject of debate.The discount rate is the weighted sum of the cost of debt and equity. There are several methods for determining the cost of equity. This study considers the commonly applied Capital Asset Pricing Model (CAPM) and Gordon’s Wealth Growth Model because of their simplicity and availability of parameters required to estimate the cost of equity. This study explores how differences in the cost of equity obtained by these two methods can be explained for a mining environment. Data for empirical analysis were collected from the I-Net Bridge, McGregor BFA, and Bloomberg databases. It was found that Gordon’s Wealth Growth Model provides better estimates of the cost of equity compared to the CAPM under depressed market conditions. Therefore, this research recommends that Gordon’s Wealth Growth Model be used to estimate the discount rates for mining projects during periods of depressed market conditions."

Jan 1, 2016

By A. du Plessis

The study summarized in this paper focused on expanding existing South African mine closure cost calculation models to provide a new model that incorporates risks, which could have an effect on the closure costs during the life cycle of the mine. This research is important because currently there are a number of mines that do not have sufficient financial provision to close and rehabilitate the mines. The magnitude of the lack of funds could be reduced or eliminated if the closure cost calculation is done in a more risk-orientated manner. The model consists of an expansion of existing closure cost calculation models, by applying the Monte Carlo risk simulation technique to model influences of external and internal changes affecting closure costs. It is shown that the proposed risk-based model provides a way to understand better the implications of uncertainty on the closure costs.

Jan 1, 2006

By N M. Vegter, C B. Kohler, E H. O Meyer

Zincor operates four Lurgi fluidised-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Based on its condition, Roaster 3 was the first to be rebuilt in 2006. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled due to the combined effects of too-high operating temperatures and corrosion caused by the following two main factors: ? Thicker external insulation was installed during a previous maintenance shut which resulted in and increased steel shell temperature and exacerbated the normal metal fatigue; ? SO2/SO3 containing gas that had permeated through the brick lining, passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but upon dismantling more damage was found and the roaster was rebuilt from the tuyeres upwards. During the rebuild, the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d&apos;images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l&apos;eau dans la roche. Une nouvelle technique expérimentale, se servant d&apos;un identificateur principalement constitué d&apos;iodure de potassium (KI), est proposée avec la méthode de l&apos;analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

The processes by which particles and bubbles interact capture many of the central concepts of colloid science and hydrodynamics. This area of research embraces hydrodynamics, interfacial(including capillary) forces, particle and bubble behaviour and solution chemistry. In this review, we discuss collision, attachment and stability efficiencies. We deal with the identification of a flotation ?domain?, the deformation of a bubble surface upon interaction with a solid surface, the kinetics of three phase contact line expansion and the determination of attachment efficiencies through to the direct measurement of bubble-particle interaction forces. We have recently carried out a test of collision theory where the latter embraces both inertial and centrifugal forces. The real challenge is now to quantitatively describe the behaviour of real systems and to incorporate a reliable description of the behaviour of particles in flotation froths. The approach described is very robust when applied to flotation, both from qualitative and quantitative points of view, providing an intellectual foundation for understanding this complex process in separation science and technology.

Jan 1, 1999

By A. Swanson

The Australian coal industry has been subdued in recent years and only a few new plants have been constructed, but the drive for greater efficiency has seen continued technological developments. The paper lists the new plants and major upgrades, plus summarizes technical developments in the areas of dense medium processing, fine coal treatment, froth flotation, dewatering and on-line analysers.

Jan 1, 2001

By S. R. Sankaranarayanan, T. Sowmya

Slags and fluxes used in metallurgical processes are typically made up of oxides (especially silicates), with additions of fluoride and carbonaceous matter. Despite the efforts made towards understanding the role of slags in various processes, little information is available on the structure of these slags. Tools such as X-ray diffraction, spectroscopy, and electron microscopy could be used for this purpose. This paper is based on an ongoing spectroscopic and structural investigation of slags and related materials. Spectroscopic studies of various commercial slags (predominantly ferrous), ores, glass and related materials, covering a wide range of compositions, have been carried out to understand the structure. The infrared spectra were recorded, predominantly, using FTIR spectrometer (Bruker IFS 66U) spanning 4000 to 100 cm-1using the KBr pellet method. The resolution was typically 4 cm-1. The spectral outputs have been compiled in terms of bands present (corresponding to different bonds) and then compared with the typical bands expected for such bonds. Efforts are in progress to identify the trends with respect to the chemical composition?for example, the effects of SiO2, Al2O3, and non-bridging oxygens. Data obtained so far indicate some trends such as (i) a shift in the Si-O band (969 to 1099 cm-1) towards a higher wave number with increasing silica content (almost 2 to 92 weight percentage) and (ii) further strong shifts as a function of the alumina content. These are being further investigated structurally and in terms of chemical composition/parameters. Keywords: slags, silicates, structure, spectroscopic analysis, shifting of bands

Jan 1, 2004

By R. L. Gibson

Manpower competencies in the mining, minerals processing and energy industries in South Africa into the next century will, to a large extent, derive from the nature and quality of the teaching which pupils receive at school. This paper provides an overview of the current developments towards a new National Curriculum in South African Schools and highlights areas in which the Minerals Industry might provide input into this process.

Jan 1, 1997