Search Documents

By L. Dison

There are many potential uses in gold mining for an initially stiff element of backfill that will yield at a predetermined load and maintain that load to beyond a compression of 30%. Such elements could be used as yielding rib pillars, as replacements for more conventional supporting packs, as con- fining bulkheads for mass backfill, as supports to provide lateral constraint, and load-carrying augmentation to overloaded rock pillars. The paper describes a system of reinforced cemented backfill that can be used to provide the above requirements. The necessary characteristics of the reinforcing and the cemented tailings are described together with the method of design to obtain a predetermined stiffness and yield load. The load-compression characteristics of the reinforced tailings elements are described and the effect of changing various of the design parameters is demonstrated.

Jan 1, 1988

By H. Vuthaluru, O. Kavianipour, C. -Z. Li, N. Suresh, D. Sahu

The paper describes a CFD model developed for 76mm Dense Medium Cyclone (DMC) using Ansys Fluent Software to gain insights into the separation of particles according to their size and density. The simulation used in this paper includes the Reynolds stress model to predict the turbulence inside the cyclone body. An Eulerian-Eulerian multiphase CFD model was applied to model a number of physical aspects such as the separation of coal particles and the segregation of magnetite media solids. The experimental results generated in a laboratory scale DMC were used for the validation purpose and the predicted results of CFD have been validated for the flow splits of water, magnetite and coal. The simulation results obtained from the Eulerian-Eulerian multiphase model revealed that the prediction agreed with experimental results, and matched reasonably well in terms of the mass flow rates of water, magnetite and coal. Furthermore, the partition curve of the DMC when mapped for the separation of - 3.0+0.50 mm size also showed to be in agreement with the experimentally obtained curves. The gravity of cut (SG50), also predicted by the Eulerian-Eulerain multiphase CFD model, was found to be in the vicinity of observed experimental value of SG50. Keywords: Dense medium cyclone, Eulerian-Eulerain multi-phase modelling, computational fluid dynamics, cut gravity (SG50)

Jan 1, 2020

By P. T. Slatter

The role of viscometers for rheological characterization in the hydraulic transport of solids is discussed, and rheological models and phenomena pertinent to the hydraulic transport of backfill material are reviewed. The two main branches of viscometry (rotational and tube) for the measurement of mining slimes rheology are compared. The effects of solids concentration, particle size and chemical additives and the practical application of rheology in backfill system design are presented.

Jan 1, 1988

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

By Peter N. Calder, Alan Bauer

The complexity of modem open pit load-haul-dump systems is described, and the need for realistic working models is pointed out. Both standard and probabilistic simulation procedures are discussed, probabilistic simulation being indicated as the more powerful and practical technique. Acquisition of the necessary pit operating data required for simulator construction and general modelling procedures are described. Finally, results from a typical open pit simulator are used to indicate the scope of the technique.

Jan 1, 2014

By B. Sergeant

Any study of the contentious subject of nationalization can ultimately be reduced to a sombre analysis of the simultaneous, and very different, interests of capital, labour, and government. Each of these interests attempts to maximize its objectives, subject to checks and balances provided, in an ideal system, by a country's executive government, legislature, and judiciary. Where even one of the three interests goes out of control, the consequences can be disastrous. The case histories show that when this occurs, the most common culprit is government, or its proxy, such as a dictator. At the other extreme, the case studies indicate that the optimum outcome occurs when capital, labour, and government are 'ring fenced' from each other: each enjoys its rights, but is also subject to duties. 'Conflicts of interest' between the three entities are ideally avoided to the maximum possible extent. The case studies include several salient instances from both the DRC (Gécamines, La Générale des Carrières et des Mines) and Zambia, along with Ghana and Chile. Further instances are examined in South Africa (gold), India (Coal of India), Brazil (Petrobras), Venezuela (Petróleos de Venezuela), Sweden (Luossavaara-Kiirunavaara Aktiebolag), Mauritania (Société Nationale Industrielle et Minière), Norway (Norsk Hydro), Botswana (Debswana), and Namibia (Namdeb). The article concludes broadly that South Africa's minerals sector is not ready for nationalization.

Jan 1, 2013

By R. Gurung, S. Asokan, Ch. V. G. K. Murty, R. Upadhyay

Tata Steel Limited which is Asia?s first and India?s largest integrated private sector steel company, as part of its vision to grow in related industries is also undertaking the Titania project. The project will involve mining, separation of ilmenite and other valuable minerals from the inland heavy mineral sands deposit in the Indian state of Tamil Nadu. The raw material will be beneficiated to synthetic rutile, titanium dioxide pigment and ultimately to titanium metal. The recently concluded feasibility study revealed that the deposit under consideration has 10.4%of total heavy mineral content and 15.2% slimes of the size below 63 µm, over an average sand thickness of 6.9 metres. The presence of about 15% slimes in ROM sand coupled with scarcity of water at the project site complicates the slimes handling/disposal system, requiring the development of an innovative, efficient and effective system for disposal of slimes. Mineral characteristics of slimes revealed the presence of kaolinite clay, which poses its own challenges in thickening/dewatering of slimes. This paper outlines the detailed studies conducted, including slime characterization, settling and thickening characteristics, and ge-technical studies to arrive at an efficient and effective slime handling/disposal system, with a view to plant saplings on the mined-out reclaimed land with species typically suitable to that environment.

Jan 1, 2007

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By N. Boegman

The meteorological conditions in South Africa are not conducive to the effective dispersion of air pollutants. In the light of this, and because of the magnitude, concentration, and future growth potential of the metallurgical industry, control of air pollution is essential. Methods of abatement are discussed for each branch of the metallurgical Industry, as well as for open-cast mining and bulk ore storage. Some recommendations are made regarding potentially rewarding research and development.

Jan 1, 1978

Book reviews Jones, M. J. (editor). Process engineering of pyrometallurgy. Proceedings of a joint meeting of the Institution of Mining and Metallurgy and the Institution of Chemical Engineers. London, Institution of Mining and Metallurgy, 1974. 105 pp. £6,50. Nim reports Report No. 1656 The analysis of geological samples for trace elements by direct-reading emission spectrometry. Report No. 1669 An assessment of the carbon-rod atomizer for the determination of silver.

Jan 12, 1974

By R. C. O’Ferrall, W. G. Goulding

This paper describes the performance of a Robbins 52R Boxhole Borer from its introduction into the mine in July 1975 until late in 1977. As indicated by the costs involved, the performance has increased considerably and is expected to be even better once further envisaged modifications have been made. The average cost for the first half of 1977 was R275 per metre bored as against an average of R628 for 1975.

Jan 1, 1978

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By K. Andres

This paper presents the vibrating mill technology and summarizes the grinding principle of ultra fine grinding. In addition, a variety of operations is described and the benefits of these different operating modes? product size and efficiency are specified. A case study of an industrial application is presented to show the integration of vibrating mills into grinding circuits. The primary focus is the overall process scheme of this technology, the installation and operating costs, as well as the design parameters required for best performance. The vibrating mill can be used in a wide range of applications for process engineering duties. For a wide range of applications, from soft to extremely hard products, which require ultra fine grinding, surface activation or homogenization, the vibrating mill is well proven. Due to its easy operation, versatility and operation efficiency, the PALLA? vibrating mill gains in importance in the mineral processing industry. Keywords: Coal, comminution, grinding, mineral processing

Jan 1, 2010

By J. A. L. Napier, J. S. Kuijpers

SYNOPSIS This paper demonstrates that the horizontal stresses induced by the creation of a tabular scope in a single mining step are always tensile at the centre of the stope span, but that compressive stresses are actively generated in hangingwalls and footwalls during sequential mining. A stress-distribution mechanism is introduced, and is used to explain the results for elastic behaviour, and for inelastic behaviour both during a single mining step and during multiple mining steps.

Jan 1, 1991

By J. H. Viljoen, J. F. Morrison, C. H. Wyndham

SYNOPSIS Heart rates, oral temperatures, shovels/min and number of 3/4 ton cars/hour trammed over distances of up to 350 ft were measured in samples of 6-10 miners, engaged in tram-shovelling, at 76°, 84°, 86°, and 89°F wet bulb temperatures in stopes in a mine. From the results it has been concluded that a man with an 'average' maximum oxygen intake capacity of about 2. 8 litres/min should be able to work: at 6 shovels/min, or 30 cars/shift per two men, at 76°-84°F; at 5 shovels/min, or 27 cars/shift per two men, at 86°F; and at 4 shovels/min, or 24 cars/shift per two men, at 89°F wet bulb air temperatures. INTRODUCTION A number of gold mines in South Africa still use tram-shovelling extensively. In this method of rock removal from the face of the stope, Bantu mine workers load rock into cars and tram the cars to a centre gulley where they are emptied. Previous studies from this Laboratory3 have shown that tram-shovelling is one of the most arduous tasks underground. The rate of energy expenditure is relatively high, being an oxygen consumption of about 1.4 litres/min over a period of some hours. In cool air conditions the upper limit to the rate of production of the well-motivated men employed on tram-shovelling has been shown1 to depend upon their capacities for physical work of an endurance nature (as measured by their maximum oxygen intakes). However, in hot conditions the factors which set the upper limit to the rate of production are different. They are primarily the ability of the body to maintain a heat balance between the rate of heat production, due to physical work, and the hot atmosphere, so that the men do not develop excessively high body temperatures8. In order to give mine managers guidance on the 'optimum' rate of production of Bantu mine workers engaged upon tram-shovelling under different temperature conditions underground a study was carried out in a mine. The number of shovels per minute and cars per hour were recorded and heart rates and oral temperatures were measured throughout the duration of the shift on samples of 6-10 Bantu mine workers in different air conditions. The results of the study are recorded in this paper and conclusions are drawn as to the number of shovels per minute and cars per hour which Bantu mine workers of 'average' maximum oxygen intake capacity should be able to produce at wet bulb air temperatures of between 76° and 89°F without either excessive fatigue or danger of heat illness.

By M. Ndabeni, J. H. van Vreden, M. Le Roux, Q. P. Campbell

It is not uncommon for gold slurry ponds or screen oversize dumps to contain several different types of carbon-rich contaminants. These contaminants act as robbers of dissolved gold which has a detrimental effect during the downstream carbon-in-leach (CIL) or carbon-in-pulp (CIP) processes. With a renewed interest in the reprocessing of contaminated gold waste ponds and dumps, preconcentration of the feed to either the CIL or CIP process becomes important to maximise profits from these resources. An added advantage in removing these resources, which were once thought of as being uneconomical, is the availability of land that can further be rehabilitated for community development projects. For gravity separation, an example of suitable technology is the Reflux Classifier (RC), which can be used for the separation of materials of different densities and can be used as a pre-concentration step. In this project, a laboratory-scale Reflux Classifier was used to pre-concentrate a gold-bearing sample obtained from a waste dump situated to the east of Johannesburg, South Africa. The material had an average gold grade of 1.9 g/ton and a carbon content of 10%. This material was first fed to a semi-batch Reflux Classifier that was used to fractionate it into several different density intervals by varying the fluidisation water feed rate, followed by continuous runs at fixed water flow rates. The results showed that a cumulative gold recovery of 60%, carbon recovery of 85%, and mass pull of 41% was possible for a fluidisation water feed rate of 15 L/min, while a rate of 20 L/min resulted in a gold recovery, carbon recovery and mass pull of 83%, 92% and 79% respectively, which translated into a concentrate gold grade above the set target of 3 g/ton. Continuous operation at 20 L/min yielded an underflow stream with 84% gold recovery at a grade of 5.4 g/ton. Keywords: Reflux Classification, gold recovery

Jan 1, 2020

By J. Kitagawa

The principal objectives of a metallurgical test programme for a 'grass roots' mining project are twofold. The first requirement is to establish the metallurgical viability of the project by demonstrating that acceptable results can be obtained by processing of the ore. The second goal is to obtain essential supporting data to determine whether the project is economically feasible. This involves several functions, which include the establishment of a workable flowsheet, the obtaining of design criteria for the commercial plant, and the collection of the evidence necessary to convince management, and often a third-party expert, that the metallurgy predicted for the ore can be achieved in a full-scale operation. The latter task is facilitated if a coherent overall picture is presented considering the geology of the orebody, the mining plan, and the mineralogy and metallurgy of the ore. The purpose of this paper is to provide guidance in the establishment of a test programme to meet the above objectives.

Jan 1, 1978