Search Documents

By Mark S. Stagg, Virgil J. Stachura, John W. Kopp, David E. Siskind

The Bureau of Mines studied airblast from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Research results obtained from direct measurements of airblast-produced structure responses, damage, and analysis of instrument characteristics were combined with studies of sonic booms and human response to transient overpressures. Safe levels of airblast were found to be 134 dBL (0.1 Hz), 133 dBL (2 Hz), 129 dBL (6 Hz), and 105 dB C-slow. These four air- blast levels and measurement methods are equivalent in terms of structure response, and any one could be used as a safe-level criterion. Of the four methods, only the 0.1-Hz high-pass linear method accurately measures the total airblast energy present; however, the other three were found to adequately quantify the structure response and also represent techniques that are readily available to industry. Where a single airblast measuring system must be used, the 2-Hz linear peak response is the best overall compromise. The human response and annoyance problem from airblast is probably caused primarily by wall rattling and the resulting secondary noises. Although these will not entirely be precluded by the recommended levels, they are low enough to pre- clude damage to residential structures and any possible human injury over the long term.

Jan 1, 1965

By Charles Vaught, Michael J. Brnich, Henry P. Cole, John V. Haley, William J. Wiehagen

Forty-eight workers who bad escaped large underground coal-mine fires were interviewed using an open-ended protocol. This information, and the actual experiences of one eight-person mine-section crew who escaped from a Fire, were used to construct an 18-frame (page) table-top simulation exercise, which was then field tested with 134 miners. The exercise is a research toot that measures miners' proficiency in the information-gathering and decision-making skills related to escaping from a mine fire. It also helps miners to learn and practice these cognitive skills. The exercise was found to be valid and reliable. All miners reported that the exercise was authentic and would help them to remember important information. The exercise total score, and all but two item scores, significantly discriminated among miners with different levels of training. The two items that did not discriminate dealt with whether or not to abandon a helpless fellow miner. When the exercise total score data were pooled, only 13.6% of the miners achieved a desirable score of 90% mastery or greater. The simulation is important because it teaches and assesses critical judgment and derision-making skills that are rarely addressed in miner training. Index Terms- Coal mining, critical skills, decision making, emergency escape and evacuation, escape from fire judgment training, mining, safety training, simulation training, under-ground mine fires.

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

Continuously separate mixture of non-magnetic materials (such as scrap, precious metals, or certain ores) at a reasonable cost. Approach Nonmagnetic materials of different densities are rapidly float/sink separated by an augmented lifting force produced In a magnetic fluid (liquid) by the effect of an external magnetic field. The magnetic fluid is a colloidal suspension of magnetite In kerosene, prepared by a low-cost process. How It Works Separation is accomplished in an open trough filled with magnetic fluid. A magnetic field is established in the fluid, by energizing an electromagnet having poles on each side of the trough. Due to the design of the magnet poles and air gaps, the magnetic field is strongest at the bottom, about 10,000 oersteds, and uniformly decreases in strength to about 2,000 oersteds at the top of the fluid. Therefore, the magnetic field gradient increases with depth. The magnetic force attracts the entire separation medium (magnetic fluid) creating a reaction force of equal magnitude and acting in the opposite direction. This reaction created within a magnetic fluid/magnetic field combination is called a magnetic levitation force. It increases with the field strength. In this case because the magnetic field is strongest at the bottom of the trough, the magnetic levitation force will quickly float lighter material while heavier material sinks.

Jan 1, 1980

By Travis Q. Lyday

Gold continued to dominate mineral production in the group of volcanic islands and atolls of Melanesia in the southern Pacific Ocean, which comprise the British Commonwealth nation of Fiji. The Fijian mineral sector, however, remained of minor importance in terms of export earnings, Government revenues, and employment to the economy of the country, which was primarily agrarian with sugar as its mainstay. The Vatukoula gold-silver mine on the north side of the main island of Viti Levu remained the largest and most important mining operation, as well as Fiji's only operating metalliferous mine. In October, Western Mining Corp. (Fiji) Ltd. (WMCF), a wholly owned subsidiary of Australian-registered Western Mining Corp. Holdings Ltd., increased its interest in the Vatukoula joint venture from 10% to 20% by exercising its option with Emperor Gold Mining Co. Ltd., also of Australia. The assumption of mine management operations at Vatukoula in 1983, with its attendant influx of additional capital and technological expertise, enabled WMCF to increase both efficiency and output at the mine during 1984. Higher output was obtained owing to an increase in underground ore production, which was partly offset by a reduction in opencut tonnage, as well as to modifications in the recovery circuit. Rate of recovery increased from about 15% to over 82% of the gold contained in the ore and from about 40% to 45% of the contained silver.

Jan 1, 1986

Provide the technology to remotely control a thin¬-seam continuous mining machine from a safe location hundreds of feet outby the working face in an underground room-and-pillar mine. Background and Approach Hard-wired or radio remote control of continuous mining machine has been commercially available since the early 1970's. This type of remote control, in low and high coal seams, situates the machine operator offboard, but within direct view of the underground coal face, Although positioned under supported roof, the operator can still be exposed to face area hazards that include roof-rib falls, dust, methane explosions, and equipment congestion. The U.S. Bureau of Mines approach has been to put the operator into a protected compartment at a location away from the working face. Since 1979, the Bureau has investigated innovative methods to better protect face area workers in under¬ground room-and-pillar mines. In 1989, the Bureau demonstrated an offboard, computer-based remote con¬trol system in a West Virginia highwall mining operation that stationed the operator hundreds of feet away from the working face. In late 1992, much of this technology, plus improvements, Was used to demonstrate, on the surface, how a thin-scam continuous mining machine could be remotely controlled 200 feet from the machine in a 36-inch working height.

Jan 1, 1992

By S. J. Page, J. A. Organiscak

Dust surveys were conducted around small truck-mounted rock drills operating at surface coal mines to assess their airborne respirable dust generation and in-service dust control methods. Of four out of seven drills sampled, respirable dust concentrations measured around the drill deck ranged from 8.68 to 95.15 mg/m with3concentrations ranging from 1.37 to 2.69 mg/m at distances 12.2 to 30.5 m downwind of these drills. The other3drills had noticeably lower respirable dust concentrations measured around the drill deck at or below 1.30 mg/m.3Rotoclone-type dry dust collectors were commonly used with dust being emitted from around the drill deck shroud, collector exhaust, and collector fines dumping. Wind speed and direction was also a factor in the dust concentrations measured on the bench. Dust control modifications were made to three rock drills to reduce their airborne dust emissions. Dust controls tested included water injection into the Rotoclone exhaust, Rotoclone exhaust extension, improved sealing of drilling deck shroud, shrouding the Rotoclone hopper dump process, and wet drilling. These control techniques showed noticeable improvement in dust concentrations measured around the drills. Finally, repositioning the drill operator showed that operator dust exposure can be improved by avoiding the dust cloud around the drill.

Jan 1, 1995

By R. H. Sprute

The Federal Bureau of Mines performed laboratory tests using direct current to dewater and densify fine-grained coal sludge in order to alleviate disposal problems and lead to recovery of high energy value often present in this waste. The laboratory tests described in the main body of the report were performed on thickened underflow (no flucculant added) from a northern Appalachian coal preparation plant. Solids in this slurry was very fine with 65 percent of the particles less than 0.1 mm in diameter. A variety of application procedures tested is exemplified by a test in which a soupy slurry (55 percent dry-weight moisture content) was converted into a firm dense material with a 20-percent dry-weight moisture content. These results were achieved in 3 hours with current density of 3.7 amp/ft2 and a power expenditure of 35 kwhr/yd3. The treated material has an average heating value of 10,400 Btu/lb. Varying current density, electrode configuration, and placement depth makes application of the treatment flexible. Two other types of sludge were tested briefly--thickener underflow from a southern Appalachian coal preparation plant with flocculant added, and sludge from an acid mine drainage treatment plant. The underflow responded well to the treatment, but response of the sludge from the acid mine drainage treatment plant was poor.

Jan 1, 1976

By Lloyd A. Morley, Robert Stefanko

The most time-consuming research segment was assembling the ref¬erences. These are provided immediately after the conclusions but are divided into two categories. The first is directly applicable publi¬cations, correspondence and personnel communications. The second listing contains those publications that are not directly tied to the research but where a probable application exists. In both listings, all important USBM publications are provided. The reference numbers used in the report apply only to the first reference portion. Further¬more, it should be noted that all entries are not used but are retained to help anyone who wishes to look further into different or allied areas of this research topic. Explosion-proof enclosures have been researched since approxi¬mately 1906. Even so, little is understood about the mechanism by which they are effective. Due to the voluminous literature published, there is a good probability that the assembled list is still incomplete. The literature search took the following directions. Work was first directed to reviewing the several references assembled by the Department of Mineral Engineering - Mining Section prior to the present project year. As a result, some duplications and inapplicabilities were found and eliminated. The primary sources of the previous search were the commonly available and usually superb library listings, such as Engineering Abstracts. Because these sources have enormous content on all subjects, they were cross-checked in the first semiannual period several times by different individuals to make sure all normally avail¬able literature were uncovered.

Jan 1, 1974

By Martin H. Stanczyk

Two methods of recovering zinc from zinc ammonia complex solutions were investigated. One method studied was distillation of the ammonia from the solutions to recover a basic zinc sulfate, which after calcining to zinc oxide was reduced to metallic zinc using hydrogen at 900° C. The second method tested was electrolysis. The tests were made of synthetic and leach solutions analyzing about 80, 100, and 115 gpl (grams per liter) of Zn, NH3, and SO4, respectively. The leach solutions were prepared by oxidation leaching of a sphalerite flotation concentrate, assaying 55 pct zinc at elevated temperature and pressure. The distillation method recovered about 98 pct of the zinc in a product analyzing 97 pct zinc. Ammonia losses incurred during the leaching and distillation operations were about 0.1 lb per lb (pound per pound) of metallic zinc produced. Electrolysis of the solutions at a cathode current density of 25 amp per sq ft (ampere per square foot) yielded zinc deposits assaying in excess of 99.9 pct zinc. About 1.5 kwhr (kilowatt-hour) of power were consumed per pound of zinc deposited; the current efficiency was 72 pct. Other electrodeposition tests revealed that small amounts of ferric iron in the cell liquor were deleterious to electrolysis unless about 5 lb of glue per ton of zinc were present in the electrolyte. The use of glue and vigorous agitation of the electrolyte gave smooth zinc deposits from solutions containing as much as 0.1 gpl iron.

Jan 1, 1962

By J. F. Barkley

 This paper describes the method used and results obtained in testing a hand-fired down-draft furnace at a plant in Washington, D. C., in order to determine the method of firing that would give the best results with a minimu of smoke. The smoke regulations of the District of Columbia are very rigid, and are well enforced, A paragraph of the ordinance relating to furnaces other than household, reads, "The emission of dense or thick black or gray smoke or cinders from any smokestack or chimney 113ed in connection with any stationary engine, steam boiler, or furnace of any description within the District of Columbia shall be deemed, and is hereby declared, to be a public nuisance". This ordinance, if literally enforced, would eliminate all ordinary hand-fired grates and furnace combinations where coal other then anthracite is used. However, in several Gov- ernment plants where hand-firing of coal is still necessary conditions have been satisfactorily met by installing the down-draft type of furnace. In these plants, as at all hand-fired plants, considerable difference in operating details and methods is found. The firemen are paid day laborer's wages and are often inexperienced. The instructions of the furnace makers fre- quently do not appeal to the firemen, and are not closely followed, This is partly due to the necessity of running the boilers continuously at much higher ratings than were intended by the manufacturer. Tests were made on a Hawley furnace of this type to improve the methods of firing, particularly at the higher ratings.

May 1, 1924

By J. W. Montoya

The chemical, mineralogical, and physical properties of berylliferous tuff from Spor Mountain, Utah, were determined in laboratory research conducted by the Bureau of Mines. Two beryllium-bearing minerals--a hydrated form of bertrandite and a berylliferous saponite--were found to be present in the tuff. Each of the beryllium mineral forms predominated in samples from certain areas of the district. The possibility of practicably separating the beryllium minerals from the tuff by physical methods appears remote because of the complexity and nature of the mineral associations. Beryllium mineralization in the region occurs in a rhyolitic tuff usually overlaid by unaltered rhyolite. The beryllium is distributed erratically throughout the tuff in individual mineralized bodies. Many samples of mineralized tuff were examined and found to contain from 0.2 to 1.8 percent BeO. All samples contained a hydrated form of bertrandite that was nearly cryptocrystalline, whereas samples from one area also contained a berylliferous saponite of variable beryllium content. Neither mineral has been previously reported, although related bertrandite-like minerals have been found in the U.S.S.R. and berylliferous minerals of the montmorillonite group have been synthesized. Most of the minerals of the tuff are finely crystalline, intergrown, and have similar densities. The complexity and intimacy of the mineral associations, the difficulty of achieving effective mineral liberation, and the highly friable nature are characteristics that lead to the conviction that tuff of the type examined cannot be effectively concentrated by gravity, magnetic, electrostatic, attrition, washing, sizing, or flotation methods.

Jan 1, 1962

By Douglas D. Reynolds, Tarek Deeb, Qunli Liu

Landmines are a great threat to military vehicles and their occupants. Mine blasts can completely destroy vehicles and kill all the occupants or disable the vehicle and leave the occupants severely injured. Injuries sustained during a landmine blast come from fragmentation that enters the vehicle through a hull breach, hot gasses expanding through the vehicle, or shock created from the extreme pressure of the blast (Lafrance, L.P. 1998). Mitigating the high acceleration experienced by the occupants during survivable mine blasts is the focus of the research being addressed in this paper. Method The objective of the project reported in this paper was to prove the feasibility that pneumatic seat technologies that employ light-weight, foam-filled, inflatable air bladder seats and seat backs can be used to protect the crews of lightweight combat vehicles against the detrimental and injurious effects of mine blasts. This protection includes reducing the shock energy experienced by seated vehicle crews during mine blast initiation and at vehicle slam-down to below potentially injurious levels. Figure 1 shows a schematic representation of the proposed lightweight, foam-filled, inflatable mine blast attenuating seat. It will consist of specially designed interconnected seat and seat back lightweight, foam-filed, air bladders that are supported by a rigid frame. [ ] Results Air gun tests and finite element analyses were conducted to determine the effectiveness of a light-weight, foam-filled, inflatable air bladder seat shock isolation system in isolating a vehicle occupant from the injurious effects of a mine blast. Figures 2 through 5 show analytical and experimental results associated with a 65.8 kg mass resting on an inflatable air bladder that is exposed to a shock input.

Jan 6, 2006

By James D. Sisler

Location and Age The main bituminous coal field of Pennsylvania lies in approximately twenty counties west of the mountain area which extends in a northeast southwest direction through the central part of the Commonwealth. The coal fields lie in a dissected peneplain, still in the youthful stage of erosion There are numerous V shaped valleys in the bituminous fields and the tributaries of the larger streams have rather steep gradients The main streams flow in rather narrow valleys with comparatively small flood plains. The coal beds of Pennsylvania are of Carboniferous age, and are confined to two systems, the Permain and the Pennsylvanian The latter system is divided into an upper or Pittsburgh series and a lower of Pottsville series The Peimain system is divided into an upper and lower series The Pottsville series of the Pennsylvanian is represented in western Pennsylvania by the Upper Pottsville only The upper or Pittsburgh series of the Pennsylvanian is represented by the Monongahela, Couemaugh, and Allegheny groups Geologic Structure. The rocks of the bituminous coal fields are folded into many anti clines and synclines extending in a general northeast direction across the western part of Pennsylvania The intensity of this folding in creases toward the mountain region West of Chestnut Ridge, which is in Fayette, Westmoreland, and Indiana counties, the folding is minor, and the coal beds have low dips East of Chestnut Ridge, v here folding is stronger, the basins are wider and the coal beds rise steeply on the flanks of the anticlines Geology. The bituminous coals of Pennsylvania are associated with shale, sandstone, clay, and limestone Each group has different proportions of these deposits, and the proportions vary at different localities within the same group.

Jan 1, 1928

By J. F. Barkley

"In trying various coals at one of the Government power plants, comparison was made of the ash softening temperature of each coal, with the clinkering tendencies of the coal when burned in the furnace. The proximate analyses, ash softening temperature and plant reports as to clinkering were tabulated. It was desired to bring out any correlation that might appear between the ash softening temperature found in the laboratory, and the clinkering of the ash as found in the boiler furnace.Each coal used was sampled and analyzed, and the standard ash fusion test made. The clinkerring of the coal in the furnace was observed by the furnace operator. The furnace equipment consisted of the ""V"" or Murphy type of stoker with the ordinary fire-brick arch roof. With such arrangement very high furnace temperatures are apt to be produced at the ratings carried at this plant.The softening temperature of ash is defined as the temperature at which small cone of the ash, as tested in the laboratory furnace, has fused down to a spherical lump, The softening interval is the difference between the softening temperature and the temperature at which the first rounding, or bending, of the apex of the cone takes piece. The flowing interval is the difference between the softening temperature and the temperature at which the ash has reached a fluid condition as shown by spreading out over the base in a flat layer.While the analyses of the different samples of the some coal did not vary appreciably, the ash softening temperatures were not always so consistent. It will be noted from the following examples that the ash softening temperatures of different samples of the same coal differ as much as 290° F, Hence, in order to judge this property of a coal, many samples ore desirable, taken from many different shipment."

Aug 1, 1924

By A. C. Fieldner

It is estimated that 6,202,235,000 gallons .of- gasoline was produced during the year 1922. The crude light oil- output Burin- the same year is estimated at 111,000,000 gallons, or 1.8 per cent of the gasoline production. In fact, if all the coal mined were coked in by-product ovens, and the light oil recovered therefrom, this product would amount to only 15 to 20 per cent of the quantity of the petroleum gasoline now produced annually. It is obvious therefore, from these figures that the light oils by present coking processes can not assume great importance as a gasoline substitute in a national sense. However, the use of light oil as a motor fuel is of real importance in districts adjacent to by-product coking operations from which a reasonable proportion of the local motor fuel supply may be derived. The certainty of diminution of petroleum resources in the relatively near future demands the utmost utilization of gasoline substitutes from the distillation of coal as well as other sources. Motor benzol is a by-product from the destructive distillation of coal. From 11/2 to 3 gallons of refined motor benzol is obtained per ton of coal carbonized. The light oil vapors are extracted from the by-product coke-oven gas by passing it upward through a series of towers in which these vapors are absorbed in a descending current of "wash" oil (petroleum distillate). The light, oil is recovered from this wash oil by distillation with live steam, the resulting crude light oil consisting of a mixture of benzol, toluol, xylol, solvent naphtha, and a small amount of other substances (unsaturated hydro-carbons, carbon disulphide, and other sulphur compounds, phenols and pyridines) is then transferred to an intermittent still and fractionated into crude motor benzol, which includes the toluol and a part of the xylol or light solvent naphtha. The crude, motor benzol is yellow in color, contains sulphur compounds which corrode copper and brass, and also contains unsaturated bodies which oxidize and polymerize on standing, producing sediment and forming gummy deposits highly objectionable when the benzol is used in motors. These objectionable

Jan 1, 1923

[ ]

Jan 1, 2012

[ ]

Jan 1, 2012

By Julian Vigil

Mountain bumps have been a problem in the coal-mining industry since the 1920's. The problem became severe in the late 40's and early 50's with the introduction of mechanized mining. Fatalities and serious injuries resulted from mountain bumps during this period. Mountain bumps again caused fatalities in the 80 's. Interviews were conducted mostly with retired coal miners having experience in bump conditions with five different coal companies. These men held positions as president, general manager, roof-control specialist, mining engineer, inspector, superintendent, mine foreman, shift foreman, section foreman, miner operator, electrician, and general laborer. Together, their comments give a good idea of the things tried to mitigate mountain bumps in the Appalachian Coal Fields.

Jan 1, 1991

By John B. Goodman

This report presents a study of a modification of the precision laboratory carbonization-assay apparatus that renders the unit capable of performance at low-, medium-, and high-temperature assay levels and permits, under controlled conditions, evaluation of the relationship between carbonization temperature and the yield of pyrolysis products. Second, the interest and value derived from the temperature study data directly apply to the particular semiplant carbonization processes and techniques currently being investigated in this laboratory. Data obtained with the assay apparatus enables the fuel technologist to predict the probable yields of carbonization products from pilot-plant operations under various carbonizing conditions. Data obtained with the assay apparatus has been used to predict the product yields of industrial carbonization plants at Kemmerer, Wyo., and Rockdale, Tex. The assay provides a useful tool in detecting, from the carbonized plant product, the degree of effectiveness of pilot-plant operation. Third, the residual volatile matter in some industrial carbons has broad significance. Evaluation of the volatile material remaining with or in the carbon may be assessed through the high-temperature-assay technique. The low-temperature carbonization assay devised by the writers has proved to be a versatile tool in predicting the probable product yields from pilot-scale carbonization processes. The apparatus described in previous publications has been modified to extend the range of testing above 500° C. without impairing the accuracy and reproducibility obtained in the low-temperature range. Results presented here include product yields from a typical Texas lignite and Wyoming subbituminous-B-rank coal over the temperature range 150° to 1,000° C.

Jan 1, 1958